Quick Cable Battery Rack User Manual

Optional Seismic Kit Installation

The purpose of the seismic kit is to secure batteries tightly in place on the
battery rack so that they cannot slide around or move independently during a
seismic event.

The seismic kit contains:

• 10 seismic spacers (long tubes threaded in both ends)

• 10 6” long 3/8 x 16” threaded bolts

• 10 2-1/2” long 3/8 x 16” threaded bolts

• 20 flat washers

• 20 lock washers

Installing the seismic kit

1. Unbolt and remove the front retaining bars from the upper and lower level
battery racks. Disconnect and remove any installed batteries. (Depending on
the original installation you may or may not need to improve the floor bolts.)

Stationary Battery Rack

Assembly Instructions

Rack de baterías estacionarias

Instrucciones de montaje

Rack de batterie stationnaire

Instructions de montage

2. Ins

tall the seismic spacers by placing them with the flat end against the
back battery rack rail. Use the predrilled holes in the rack bars to locate the
spacers and bolt them to the back rack with the 2-1/2” long bolts, using a
washer and lock washer at each location.

3. Reinstall the front retaining bar by turning it around so the tabs are on the
inside of the vertical end pieces. The idea is that this bar is going to compress
against the front of the batteries once they are reinstalled. Use the 6” threaded
bolts, washers and lock washers as shown to assemble

the front bar loosely.

4. Tighten the bolts as necessary to securely fit the front retaining bar against
the battery bank.

Copyright© Quick Cable Corporation

3700 Quick Drive • Franksville, Wisconsin, 53126-0509 U.S.A.

Quick Cable Corporation

Phone: [phone] • Fax: [phone]

Email: [e-mail]

X-890697A

Quick Cable Canada Limited

6395 Kestrel Road • Mississauga, Ontario, L5T 1Z5 Canada
Phone: [phone] • 800-728-1742 • Fax: [phone]

Email: [e-mail]

Part Number / Número de pieza / Numéro de pièce

990211-001

Before beginning assembly, check the contents of your kit against the parts list.

If any of the parts listed are missing, contact your dealer immediately for replacement.

Antes de comenzar el montaje, comprobar el contenido de su equipo en contra de la lista de piezas.
Si alguna de las partes de la lista faltan, póngase en contacto con su distribuidor inmediatamente para su reemplazo.

Avant le montage début, vérifiez le contenu de votre trousse de la liste des pièces. Si aucune

des parties est manquant, contactez immédiatement votre revendeur pour le remplacement.

Removable Bars (2)

4

Attach upper and lower front bar with 2 self-tapping
screws each.

Adjuntar superior e inferior barra delantera con 2
autorroscante tornillos cada uno.

Fixez supérieur et inférieur barre frontale avec 2
autotaraudeuse vis chacune.

Holes for external

accessories (8 places)

Battery Rack

QUICK

1

Attach to floor in compliance with local building codes.
(fasteners not included).

Adjuntar al pavimento en conformidad con los códigos
locales de construcción. (tornillos no incluidos).

Fixez au sol en conformité avec les codes de
construction locaux. (fixations non comprises).

Battery Rack

QUICK

Mounting Holes (4 places)

Lay shelf liner on wire shelves if desired

2

(liner not provided).

Lay liner estante en estantes de alambre,
si se desea (liner no incluidos).

Lay doublure étagère étagères fil si vous
le souhaitez (revêtement non fourni).

Load batteries.

3

Cargue las baterías.

Batteries de charge.

Parts list / Lista de piezas / Liste des pièces

One piece welded rack
Una pieza soldada estante
Une pièce soudée crémaillère

Battery Rack

QUICK

= x 4 - self tapping screws
= x 4 - tornillos autorroscantes
= x 4 - vis autotaraudeuses

= x 2 - front bars
= x 2 - bares frente
= x 2 - barres avant