LA MESSA IN FUNZIONE E LA MANUTENZIONE DELL’APPARECCHIATURA DEVE ESSERE EFFETTUATA DA PERSONALE
QUALIFICATO.
RISPETTARE LE PRESCRIZIONI RIPORTATE NEL SEGUENTE MANUALE E LE NORME APPLICABILI ALLA COSTRUZIONE
ELETTRICA, IN MODO DA GARANTIRE IL CORRETTO FUNZIONAMENTO DELL’ APPARECCHIATURA E LA SICUREZZA
DELLE PERSONE E DELL’AMBIENTE.
IL PRODOTTO MODIFICATO O MANOMESSO PERDE LA GARANZIA DEL COSTRUTTORE E LA CERTIFICAZIONE
PRESENTARE PROBLEMI DI SICUREZZA PER LE PERSONE E PER L’AMBIENTE.
USING AND SERVICING THE DIMMER PACK IS RESTRICTED TO QUALIFIED PERSONNEL.
FOLLOW THE INSTRUCTIONS IN THIS M ANUAL AND ALL THE RELEVANT ELECTRICAL CODES. THIS WILL ENSURE THE DE VICE’S
PROPER OPERATION AND THE SAFETY OF PEOPLE AND THE ENVIRONMENT.
TAMPERING WITH THE DEVICE WILL VOID THE MANUFACTURER’S WARRANTY AND THE
SAFET Y ISSUES FOR PEOPLE AND THE ENVIRONMENT.
CERTIFICATION, AND MAY LEAD TO
, E PUÒ
Page 2
Page 3
STRIP LE D 12V - REV001B
IT
INDICE
Pag. 4 INS TAL L AZIONE:
Pag. 5 INS TAL L AZIONE:
Pag. 6 SCHEMA DI COLLEGAMENTO / CARATTERISTICHE
Pag. 7 ESEMPI APPLICATIVI
EN
INDEX
Pag. 8 INS TAL L ATI ON :
Pag. 9 INS TAL L ATI ON :
Pag. 10 WIRING DIAGRAM / CHARACTERISTICS
Pag. 11 APPLICATION-ORIENTED EXAMPLES
istruzioni per il taglio
cappuccio alimentazione, cappuccio finale, driver
cut instructions
power cap - ending cap - driver
QUICK SPA
3
Page 4
IT
L19
20
L18R6L19
CARATTERISTICHE / INSTALLAZIONE
STRIP LE D 12V - REV001B
LEGGERE ATTENTAMENTE PRIMA DI COLLEGARE LA STRIP LED
La STRIP LED 12V Quick® viene fornita già pronta per sistemi a batteria 12V.
Quick S.p.A. non si assume alcuna responsabilità in caso di errato collegamento e/o errato utilizzo di questo
apparecchio.
PRIMA DI UTILIZZARE LA STRIP LED, LEGGERE ATTENTAMENTE IL PRESENTE MANUALE D'USO.
IN CASO DI DUBBI CONTATTARE IL RIVENDITORE O IL SERVIZIO CLIENTI QUICK®.
LA CONFEZIONE CONTIENE: Strip Led - condizioni di garanzia - manuale d’uso e manutenzione.
IMPORTANTE
F
RISPETTARE LA POLARITA’ COME INDICATO NELL’ETICHETTA DEL PRODOTTO:
CAVO ROSSO COLLEGATO AL POSITIVO DELLA BATTERIA E CAVO NERO COLLEGATO AL NEGATIVO.
La STRIP LED 12V Quick
vedono ogni tre LED.
FIG. 1
Particolare di una STRIP LED 12V Quick
®
può essere tagliata ogni 5 centimetri circa, in corrispondenza delle piazzole rosse di rame, che si
6789
L10
Il taglio va effettuato esattamente tra le due coppie di piazzole rosse di rame, lungo la linea che le divide, perpendicolare
alla lunghezza del prodotto.
FIG. 2
Taglio corretto per la STRIP LED 12V Quick
L12
IMPORTANTE
F
La lunghezza massima di Strip LED alimentabile a 12V è 5 metri con un unico DRIVER STRIP LED.
Se il prodotto viene fornito in bobina da 10 metri ed è intenzione fare una linea di luce continua, occorre tagliare la Strip LED
a metà ed ogni pezzo da 5 metri risultante andrà alimentato separatamente.
Vedere gli esempi applicativi riportati a pag. 7.
L11L12R4L13
L13L17
111213141516171819
10
L14L15R5L16L17L18R6
L14L15R5L16
4
QUICK SPA
Page 5
STRIP LE D 12V - REV001B
L14L15R5
INSTALLAZIONE
IT
Una volta tagliata una misura di Strip LED, inserire i due cavetti del DRIVER STRIP LED nel CAPPUCCIO ALIMENTAZIONE.
Saldare i due cavetti alle piazzole rosse di rame, in corrispondenza del taglio della Strip LED.
ATTENZIONE: la parte con i cavi più corti va collegata alla STRIP LED, la parte con i cavi più lunghi va collegata all’ali-
mentazione (vedi figura a pag.6)
IMPORTANTE - NELLA FASE DI SALDATURA RISPETTARE LA POLARITÀ:
F
IL CAVO ROSSO DEL DRIVER STRIP LED ALLA PIAZZOLA ROSSA DI RAME CON IL SIMBOLO + ED IL CAVO NERO DEL DRIVER
STRIP LED ALLA PIAZZOLA ROSSA DI RAME CON IL SIMBOLO
-
.
Per collegare il DRIVER STRIP LED seguire le istruzioni a pag. 6.
Per la chiusura con il CAPPUCCIO DI ALIMENTAZIO-NE si deve utilizzare un silicone neutro (non acetico).
Riempire il cappuccio con il silicone, successivamente
inserire il cappuccio nella Strip LED.
L13
CAPPUCCIO
ALIMENTAZIONE
L10
L11L12R4
STRIP LEDDRIVER
All’altra estremità occorre chiudere con un CAPPUCCIO FINALE.
Per la chiusura con il CAPPUCCIO FINALE si deve utilizzare un silicone neutro (non acetico).
Riempire il cappuccio con il silicone, successivamente
inserire il cappuccio nella Strip LED.
Il CAPPUCCIO di
ALIMENTAZIONE e il
CAPPUCCIO FINALE
garantiscono
L11L12R4
L10
L11L12R4
STRIP LED
Eventuali DRIVER STRIP LED e CAPPUCCI DI CHIUSURA necessari alla personalizzazione della STRIP LED 12V non sono inclusi
nella confezione. Contattare Quick
SCHEMA DI COLLEGAMENTO STRIP LED 12V con DRIVER STRIP LED
DRIVER
STRIP LED
nero NEG
rosso POS
RISPETTARE LE POLARITÀ.
ATTENZIONE: la parte con i cavi più corti va collegata alla STRIP LED, la parte con i cavi più lunghi va collegata
all’alimentazione.
ALIMENTAZIONE
12/24
VDC
STRIP LED
CARATTERISTICHE
Sistema
Sorgente
Voltaggio10 - 15 Vdc
Potenza consumo
Consumo Ampère0,4 A/m @ 12V - 0,6 A /m @ 15V
Protezione LedPicchi di voltagg io ± 500 V
PolaritàSì
ProtezioneIP 65
MaterialeGuaina in silicone resistente UV
Certificazioni
DRIVER STRIP LED
12 V
LED
4,8 W/m @ 12 V
GARANZIA
Il non rispetto delle prescrizioni del presente documento fanno decadere la garanzia.
In caso di discordanze o eventuali errori tra il testo tradotto e quello originario in italiano, fare riferimento al testo
italiano.
F
Quick® si riserva il diritto di apportare modifiche alle caratteristiche tecniche dell’apparecchio e al contenuto di questo manuale senza alcun preavviso.
F
6
QUICK SPA
Page 7
STRIP LE D 12V - REV001B
ESEMPI APPLICATIVI
IT
ESEMPIO 1
Ad un DRIVER STRIP LED sono collegati 5 pezzi di STRIP LED 12V da 1 metro in parallelo, raggiungendo la portata massima.
DRIVER
STRIP LED
nero NEG
rosso POS
12 VDC
ESEMPIO 2
Ad un DRIVER STRIP LED sono collegati 2 pezzi da 2,5 metri di STRIP LED 12V in serie, raggiungendo la portata massima.
DRIVER
STRIP LED
nero NEG
rosso POS
12 VDC
ESEMPIO 3
La necessità di collegare più di 5 metri di STRIP LED 12V, in questo esempio 15 metri, rende necessario l’impiego di altri 2
DRIVER STRIP LED. Viene collegato un pezzo da 5 metri di STRIP LED 12V ad un DRIVER STRIP LED, 2 pezzi da 2,5 metri ad un
secondo DRIVER STRIP LED e 5 pezzi da 1 metro al terzo DRIVER STRIP LED
DRIVER
QUICK SPA
STRIP LED
7
nero NEG
rosso POS
12 VDC
Page 8
EN
L19
20
L18R6L19
CHARACTERISTICS / INSTALLATION
STRIP LE D 12V - REV001B
READ CAREFULLY BEFORE CONNECTING THE STRIP LED
Quick® STRIP LED 12V is readily supplied for 12V battery systems.
Quick S.p.A. will not be responsible in case of wrong connection and misuse of this instrument.
READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THE STRIP LED.
IN CASE OF DOUBT, CONTACT YOUR DEALER OR QUICK® CUSTOMER SERVICE.
THE PACKAGE CONTAINS: Strip LED - conditions of warranty - the manual of installation and use.
IMPORTANT
F
ALWAYS RESPECT POLARITY AS SHOWN IN THE PRODUCT LABEL:
RED WIRE CONNECTED TO POSITIVE POLE AND BL ACK WIRE CONNECTED TO THE NEGATIVE POLE.
®
Quick
STRIP LED 12V can be cut approximately every 5 centimeters between the two pairs of copper dots that occur
after every three LEDs.
FIG. 1
Piece of a Quick STRIP LED 12V
6789
L10
The Strip shall be cut exactly between the two pairs of red copper plates, along the line separating them, perpendicular to
the length of the product.
FIG. 2
Performing the correct cut for the Quick STRIP LED 12V
L12
IMPORTANT
F
The maximum length of STRIP LED which can be supplied with 12V power is 5 meters with one STRIP LED DRIVER.
if the product is purchased in a 10 meter reel, and the customer plans to have a continuous light line, the STRIP LED should
be cut in two halves, and every 5 meters piece should be supplied separately.
See the application-oriented drawings at the pag.11.
L11L12R4L13
L13L17
111213141516171819
10
L14L15R5L16L17L18R6
L14L15R5L16
8
QUICK SPA
Page 9
STRIP LE D 12V - REV001B
L14L15R5
INSTALLATION
EN
Once a piece of STRIP LED has been cut, insert the two DRIVER STRIP LED wires in the POWER CAP. Solder the two wires
to the red copper plates, in correspondence of the cut of the STRIP LED.
ATTENTION: the side with shorter wires goes to Strip LED, the side with longer wires goes to Power Supply (see
picture to the pag. 10).
IMPORTANT - RESPECT POLARITY WHILE SOLDERING:
F
THE STRIP LED DRIVER’S RED WIRE SHALL BE CONNECTED TO THE RED COPPER PLATE WITH THE “+” SYMBOL, AND THE STRIP
LED DRIVER’S BLACK WIRE TO THE RED COPPER PLATE WITH THE “-“ SYMBOL.
To connect the DRIVER STRIP LED please follow the instructions at the pag. 10.
In order to close the POWERCAP, a neutral (non-acetic) silicone should be used.
The cap should be filled with silicone, and then inserted into the STRIP LED.
L13
POWER CAP
L10
L11L12R4
STRIP LEDDRIVER
The other end should be closed by means of the silicone ENDING CAP.
In order to close the ENDING CAP, a neutral (non-ace-
tic) silicone should be used.
The cap should be filled with silicone, and then inserted into the STRIP LED.
THE POWER CAP
and the ENDING
CAP guarantee the
L11L12R4
L10
L11L12R4
STRIP LED
Any additional STRIP LED DRIVER and CAPS needed to personalize the installation of STRIP LED 12V are not included in the
packaging. Contact Quick
L13
ENDING CAP
®
making reference to the following part numbers:
RATING
DRIVER STRIP LEDKCAD20SLSUP0
POWER CAPPCCSLPWR0000
ENDING CAPPCCSLEND0000
QUICK SPA
9
Page 10
EN
WIRING DIAGRAM / CHARACTERISTICS
WIRING DIAGRAM STRIP LED 12V with DRIVER STRIP LED
DRIVER
STRIP LED
black NEG
red POS
RESPECT POLARITY.
ATTENTION: the side with shorter wires goes to Strip LED, the side with longer wires goes to Power Supply.
POWER
STRIP LE D 12V - REV001B
12 VDC
STRIP LED
CHARACTERISTICS
Voltage system
Light source
Operating voltage10 - 15 Vdc
Power consumption
Ampère consumption0,4 A/m @ 12V - 0,6 A /m @ 15V
Led protectionSpike protected ± 500 V
PolarityYes
ProtectionIP 65
MaterialSheath in UV-resistant silicone
Certifications
DRIVER STRIP LED
4,8 W/m @ 12 V
12 V
LED
Conversion from decimal
to fractional inches
5 cm =1” 31/32 in
1 m =39” 3/8 in
2,5 m =98” 7/16 in
5 m =196“ 27/32 in
10 m =393” 45/64 in
15 m =590” 35/64 in
WARRANTY
Failure to comply with the prescriptions listed on this document will void the Warranty.
In case of discordance or errors in translation between the translated version and the original text in the Italian
language, reference will be made to the Italian text.
F
Quick® reserves the right to modify the technical characteristics of the equipment and the contents of this manual
without prior notice.
F
10
QUICK SPA
Page 11
STRIP LE D 12V - REV001B
APPLICATION-ORIENTED EXAMPLES
EN
EXAMPLE 1
Five pieces of one-meter STRIP LED 12V are connected in parallel to a STRIP LED DRIVER, reaching the maximum capacity.
DRIVER
STRIP LED
black NEG
red POS
12 VDC
EXAMPLE 2
Two pieces of 2.5 meters STRIP LED 12V are connected in series to a STRIP LED DRIVER, reaching the maximum capacity.
DRIVER
STRIP LED
black NEG
red POS
12 VDC
EXAMPLE 3
The need to connect more than 5 meters of STRIP LED 12V, in this example of 15 meters, makes the use of two more STRIP
LED DRIVERS necessary. They are connected by the 5 meters of STRIP LED 12V and a STRIP LED DRIVER, two 2.5 meter pieces
to the second STRIP LED DRIVER and five 1 meter pieces to the third STRIP LED DRIVER.