Scannen Sie den QR-Code oder besuchen Sie den URL-Link,
um die vollständige Ausgabe des Online-Handbuchs zu sehen.
Outdoor Router
Außen-Router
AC-PLUG
FOR UK / EU
US / AU
PoE Injector
PoE-Injektor 48Volt
Note: The PoE injector has either UK/EU/US/AU plug according to the destination.
Please contact us immediately if any components are missing.
2x 4G and 2x WiFi
Omni Antennas
Rundum-Antennen
L-Bracket & T-Wrench
Halterung & Schlüssel
10-Meter LAN Cable
LAN-Kabel 32,8-Fuß
Mounting Kit
Montagesatz für außen
Page 2
4G
2.4G
INTERFACE OVERVIEW
PORTS & SCHNITTSTELLEN
4G ANTENNA
STEP
1.2
OPEN THE ENCLOSURE
Use hexagon head on the
T-wrench to lose bolts in
anti-clockwise direction
CROSS
5MM HEX
T-WRENCH
5MM HEX
2.4G ANTENNA
BREATHER VALVE
13
MAIN
4
5
GLAND
PORTS 1~6 ARE EMBOSSED
NUMBERS ON THE ENCLOSURE
4G ANTENNA
HEXAGON BOLT
LOCKHOLE
CLOSE THE ENCLOSURE
Close the lid & press by hand.
Ensure no gap after closing.
Use T-wrench to tighten all
bolts in clockwise direction.
2.4G ANTENNA
6
INSERT SIM CARD & CONNECT PoE
SIM-KARTE EINLEGEN & PoE ANSCHLIESSEN
LANPoE & WANRESETDC 9~48V
SYSTEM
Ensure it has a strong mobile signal.
The modem sensitivity is -101dBm,
Firstly, take off the Cap
anti-clockwise from gland.
Push from inside of Barrel
to take out the Stopper.
PoE & LAN
BARREL
STOPPER
Smaller
( UP TO DOWN )
SIM1*
SIM2
WI-FI
PINHOLE
PIN
FOR NANO-SIM (0.5” x 0.3”)
approx 2-bar on the phone.
SIM1
SIM2
SIM-CARD TRAY
STEP
1.3
INSTALL ANTENNAS
ANTENNEN INSTALLIEREN
You can install the antennas after finishing
the below step 2 or step 3.
The 4G-LTE antennas are marked 4G
and Wi-Fi antennas are engraved 2.4G.
LOCATE ANTENNA SOCKETS
Locate embossed numbers
1~6 on the top & bottom sides
1 &3 are for 4G antennas
4 & 6 are for WIFI 2.4G antennas
Put antennas aligned at corresponding
sockets, turn the milled part on the
antenna head in the clockwise
direction to tighten them.
All of the base sockets are N-female.
Ensure alternative antennas are
UPGRADEABLE
with N-Male connectors.
STEP
2.2
PoE
Take one end of the LAN
cable through the Cap.
Put the LAN cable through
Barrel, plug in PoE & LAN port.
Clamp the Stopper on the LAN
cable & settle it in the Barrel.
Turn the Cap clockwise to
tighten it on Barrel.
Connect another end of LAN cable
to the PoE port on the PoE injector.
CAP
SIM CARD
Please turn off the power while
LAN CABLE
inserting or taking out a SIM card.
Use the PIN to push the PINHOLE,
and the SIM-Card Tray pops out.
Insert a SIM card in the SIM1 Slot.
Reposition the SIM-Card Tray
in the slot and push it back.
2.1
STEP
INDICATORS
LAN
The indicators turn on green color
when a related function is activated.
They flash when having data flow.
WI-FI
SYSTEM
MOBILE
POWER
ETHERNET
Connect a computer to the LAN port
on the PoE injector to get the Ethernet.
To use another router, connect its WAN
port to the LAN port on the injector.
ALTERNATIVE POWER
You can replace PoE injector with an
IEEE802.3af/at standard PoE switch and
the DC socket takes 9~48Volt power.
Page 3
BRACKET & MOUNTING
POLE IS EXCLUDED
HALTERUNG UND BEFESTIGUNG
FIRMWARE CONFIGURATION
FIRMWARE KONFIGURATION
STEP
3.1
SIGNAL COVERAGE
The cellular signal quality is crucial to mobile internet speed and stability. Ensure there
is fair signal coverage. The router should install in a suitable location, such as elevated,
near a window, and away from obstructions and other RF equipment.
Suggest using a smartphone and walking around to check the signal bars.
To measure the signal quality accurately, please check tutorial at
https://www.outdoorrouter.com/signal/.
STEP
3.2
INSTALL ON A POLE
Find a pole with Ø35~50mm diameter. The typical installation is on a vertical pole.
Turn the bracket to be parallel with pole when install it horizontally.
Use the cross end on T-wrench and M6 cross-head screws to install the
L-shape bracket on the backside of the enclosure.
U-BOLT
HOLDER
WASHER
SPRING WASHER
HEX NUT
STEP
4.1
CONNECT BY WIFI OR LAN
After turning on power, use a phone or computer to join the open Wi-Fi hotspot
Outdoor-WiFi-xxxx or connect the computer to the LAN port on the PoE injector.
Open a web browser, enter the router IP http://192.168.30.1 on the address bar.
Click the Login button to access the admin panel.
http://192.168.30.1
AUTHORIZATION REQUIRED
Please enter your router password!
Password
Default has no password!
STEP
4.2
SET ADMIN PASSWORDS
* If unable to access the login page,
change a web browser and recheck
the Wi-Fi or LAN connection.
Login
After accessing the router, navigate to System > System from the top menu.
Under the General Settings tab, click the Sync with browser button to sync the time.
Go to System > Administration, input new custom router password twice, then
click the Save and Apply button to save settings.
* Keep the password in a safe place.
STEP
4.3
SET WIFI HOTSPOTS
Go to Network > Wireless, there are two WiFi hotspots on the wireless overview.
Click the Disable (Enable) buttons to turn off (on) the WiFi hotspots.
Associated Stations are the active WiFi connections and their working status.
Click the Edit buttons on each SSID row to enter their configuration pages.
On the General Setup tab, you can monitor the hotspot's working status.
Suggest using default settings of Mode, Channel, Width, and Transmit Power.
U-BOLT HOLDER
SPRING WASHER
WASHER
HEX NUT
Firstly, clasp the pole with U-bolts and holders,
then attach the L-shape bracket to the holders.
On another side of the bracket, put washers,
spring washers, and hex nuts on U-bolts.
Tighten the hex nuts with an M10 spanner.
POWER ON ROUTER
Connect the AC plug on the PoE injector to the
110~240 Volt electrical outlet, and the router
will boot up automatically.
WIFI SSID & PASSWORD
Scroll down to Interface Configuration, and change WiFi SSID on the ESSID field.
Click the tab of Wireless Security, and choose WPA , WPA2, or mixed mode on
the Encryption option. Input the WiFi password in the Key field.
Click the Save & Apply button on the bottom right corner. The WiFi hotspot
takes 2~3 minutes to reboot. Then re-connect to the new hotspot.
WIFI COVERAGE
For better outdoor WiFi coverage, suggest installing the router in an open space
with the fewest barriers nearby.
To cover indoor spaces, you can install the router near the windows or doors.
You can also use an indoor router and link to the LAN port on the PoE injector.
Page 4
STEP
4.4
SETUP LTE-MODEM
The default mobile modem settings can adapt to most operators. You can find the
mobile modem Device information on the front page.
If the Mobile interface fails to connect, verify the mobile signal quality and check
with the operator if the SIM card is enabled and has data allowance.
Click the Edit button to configure the
advanced Mobile parameters.
Protocol
Active SIM
Auto Switch
SIM Card
APN
PIN
Authentication
IP Type
STEP
Turn on DHCP mode on the phone or computer to obtain a local IP address from
the router. To use a static IP address, please comply with the below format.
Computer IP
Subnet mask
Gateway
STEP
Reboot
Soft
Reset
Hard
Reset
Use QMI or PPP protocol for traditional networks and virtual operators.
* Check the tutorial at https://www.outdoorrouter.com/protocol/
Choose the SIM card slot that inserts a SIM card.
Enable it when inserting two SIM cards on both SIM1/2 slots.
It switches to another slot when Active SIM Card is offline.
Primary SIM1 / Secondary SIM2
Refer to operator's instructions to set APN, username, and password.
* Refer to the tutorial at https://www.outdoorrouter.com/apn/
Leave it blank when using the default SIM card PIN code.
Usually use PAP or PAP/CHAP authentication.
Please choose IPv4 only or both IPv4/IPv6.
4.5
LAN NETWORK
192.168.30.100~249 ( pick one IP from 100~249 )
255.255.255.0 ( 24 on Windows )
192.168.30.1
4.6
RECOVERY
Rebooting the router could solve glitches after a long period of work.
Go to System > Reboot or replug the PoE injector to reboot it.
If the router works unstable after changing settings, go to System > Backup / Flash Firmware. Click the Perform Reset button to reset it.
To run a hard reset, tap and hold the Reset button for 5 seconds when
the router is powered on. Release it and wait 5 minutes until boots up.
IMPORTANT!
DO NOT TURN OFF POWER WHILE RESETTING THE ROUTER!
OutdoorRouter
www.outdoorrouter.com
Feel free to contact us if you need any further assistance.
Bei fragen wenden sie sich bitte an nus.
CALL US
United Kingdom
United States
Australia
+44 020 3575 1156
+1 323 521 4621
+61 02 8205 3116
Thanks for reading! If you have questions while using the router,
please check the online manual at
Please feel free to contact us if you need any further assistance.
EZR33T.Router.Works
E-MAIL
sales@outdoorrouter.com
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.