Quick 3202 Operation Manual

QUICK 3202

Lead Free Soldering Station

OPERATION MANUAL

Thank you for purchasing the unit. It is designed for lead free soldering.

Please read this manual carefully before use and keep it for future

reference.

Ⅺ. TIPS

200-2.4D

200-1.6D

200-1.2D

200-3.2D

200-4.2D

200-SB

200-B

0.5

0.5

3

.

5

4

5

°

15

2

5

°

4

5

°

2

10

1.5

10

4

R

0

.

5

9

2

R

0

.

5

200-2C

7

.

5

2

12

3

4

5

°

1

.

2

3

.

5

200-H

10

3.7

200-1C

12

3.5

2

200-0.8C

4
5

°

12

200-K

1.5

200-SK

R

0

.

2

12

4

5

°

12

4
5

°

1.5

12

4
5

°

200-2B

200-3C

R

1

R

0

.

2

200-I

2

12

3

2.5

12

2

200-4C

2

12

200-J

12

3

2

4

5

°

12

12

2

3

12

1

0.8

0.8

Table of Contents

Ⅰ. Safety Instruction……………………………………………………………1
Ⅱ. Specification…………………………………………………………………3

Ⅲ. Characteristic…………………………………………………………………4
Ⅳ. Connection & Operation the Soldering Iron………………………………4

4.1 Iron Holder………………………………………………………………4

4.2 Connection……………………………………………………………5

4.3 Operation of the Soldering Station…………………………………6

4.3.1 Favorite Temperature Setting…………………………………6

4.3.2 Temperature Setting……………………………………………7

4.3.3 Turn On / Turn Off the Sound…………………………………7

4.3.4 Sleeping and Resume…………………………………………8

Ⅴ. Parameter Setting……………………………………………………………8

5.1 Input Right Password…………………………………………………9

5.1.1 Into the Parameter Setting……………………………………9

5.1.2 Input the Password……………………………………………9

5.2 Parameter Menu………………………………………………………10

5.3 Sleeping Time Set……………………………………………………10

5.4 Work Mode Set………………………………………………………11

5.5 Password Set…………………………………………………………12

Ⅵ. Temperature Calibration…………………………………………………12
Ⅶ. Select a Correct Tip………………………………………………………13
Ⅷ. Use and Maintenance of the Tip…………………………………………14

8.1 Use of the Tip…………………………………………………………14

8.2 Maintenance of the Tip………………………………………………14

Ⅸ. Error messages……………………………………………………………16
Ⅹ. Check and Replace the Soldering Iron…………………………………16

10.1 Check the Soldering Iron……………………………………………17

10.2 Disassembling the Iron Handle……………………………………17

10.3 Measure the Resistance before Replacing…………………………18

10.4 Measure the Resistance after Replacing…………………………18

Ⅺ. TIPS…………………………………………………………………………19

Page 19

Ⅰ. Safety Instruction

WARNING

In this instruction manual,“Warning ”“ Caution” and “Note ” are defined as

followings:

WARNING: Misuse may potentially cause death or serious injury to the

user.

CAUTION: Misuse may potentially cause injury to the user or physical

damage to the objects involved. For your own safety, be sure

to comply with these precautions.

CAUTION

When the power is on, the tip temperature is very high. Follow the

precautions strictly as mishandling may cause burn or fire:

 Do not use the unit for other applications.

 Do not touch the metallic parts near the tip.

 Do not use the product near flammable items.

 Inform other people in working area that the temperature of this unit

could be very high during the work. Power the unit off when the work is

finished to avoid danger.

 Power off the unit and wait till the temperature cools down to room

temperature when replace or install the parts.

To prevent damage to the unit and ensure a safe working environment,

be sure to comply with the following precautions:

 Only use this unit with rated voltage and frequency (refer to the

trademark back of equipment).

 If there’s any damage to the unit, stop using it.

1. Pull out the iron tip by the needle at the soldering handle holder. the iron tip

and the iron tip

encloser ①are in together.

2. Pull out the heating element③ towards the iron tip of the iron handle⑧.

3. Push the handle cord（ 12） lightly forwards and pull the PCB for line
connection⑥and handle cord out of the iron handle⑧ (towards the tip of the

handle).

NOTE:

Do not use metal tools such as pliers to remove tip or Tip encloser from

the iron handle.

10.3 Measure the Resistance before Replacing

NOTE:

Measure the resistance when the heating element is at room temperature.

1. Resistance value of heating element is ＜4Ω.

2.

If the resistance value is not normal, replace the heating element. Refer to the

instructions included with the replacement part.

10.4 Measure the Resistance after Replacing

After replacing the heating element:

1. Measure the resistance values “a” and “b” to confirm that the leads are not

twisted and that the grounding wire is properly connected.

2. The pins of the handle plug are as followings:

Pin1: Blue Pin2: Red

Pin3: Green Pin4: Metal layer of shielding cord

Pin5: White of shielding cord Pin6: White

Page 18 Page 1

10.1 Check the Soldering Iron

1. Pull out the plug and measure the resistance value between the pins of the

connecting plug when the heating element cooling down to the room

temperature.

2. If the value of ‘a’ is different from the values in the following table, replace

the heating element or cord assembly. Refer to the following steps.

3. If the value of ‘b’ is over the below value, remove lightly the oxidation in the

joint part of the tip and the heat element with sandpaper or steel wool.

a.

Between pins 4&5 (Heating
Element)

＜4Ω(Normal)

b. Between pins 3& Tip ＜2Ω

10.2 Disassembling the Iron Handle（for example

901A Iron hand

）

 This machine is equipped with a 3-wires grounding plug and must be

plugged into a 3-terminal grounded socket. Do not modify plug or use

an ungrounded power socket. If an extension cord is necessary, use

only a 3-wire extension cord that provides grounding.

 Do not use the unit for other applications except soldering.

 Do not rap soldering iron against the workbench to shake off residual

solder, otherwise the iron will be damaged by shocks.

 Do not modify the unit.

 Only use the original replacement parts.

 Keep the unit dry. Don’t use or disconnect the unit with wet hands.

 The soldering process will produce smoke, so make sure the area is

well ventilated.

 While using the unit, don’t do anything which may cause bodily harm or

physical damage.

 Children don’t know the danger of electrical appliances. Keep it away

from children.

Page 2 Page 17