Questyle Audio Technology T2 User Manual
Table of Content
Introduction……………………………………………………......…………………........…………02
Check list…………………………………………………….….....…………………........…………02
Front view …………………………………………………….….....…………….……........……….03
Rear view …………………………………………………….….....……………..……........……….03
CAS system …………………………………………………….….....…………..………........……04
Install the Dedicated Driver on PC ........................................................................................05
Core Audio Stream Introduction...............................................................................................07
WASAPI Setting.......................................................................................................................08
Setting on Mac OS...................................................................................................................10
Specification ............................................................................................................................10
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment
Note:This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection again
st harmful interference in a residential installation.This equipment generates, uses and can radiate ra dio
frequency energy and, if not installed and used in accordance with the instructions, may cause h armful
inerference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipme
nt does cause harmful interference to radio or television reception, which can be determined by turning t
he equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, Human proximity to
the antenna shall not be less than 20cm (8 inches) during normal operation.
1
Introduction
Thank you for selecting Questyle Audio T2 Transmitter of 5GHz Hi-end Wireless Audio
System.
The worldwide first Hi-end 5G wireless audio system was born in Questyle Audio. It provides
Hi-end sound performance with easiest wireless operation. The system is made up of wireless
Transmitter and Wireless Receiver (built-in DAC and Amplifier).
The current 2.4GHz wireless HiFi system set people free from the hateful cable decoration ,
brings an innovation on audio field. But the shortage is that it’s always be interferenced,
interrupted or delayed. Questyle 5GHz Wireless Series transmit signal in 5.8GHz frequency,
totally get rid of the 2.4GHz frequency interference, achieve more stable transmission.
T2 Transmitter support digit al input with USB, Coaxial and optical. It can also receive analogue
signal through RCA input, with built-in ADC to convert to digital signal for transmission. It’s
easy operate, can work automatically after power on. It can wireless transmit signal in
24bit/48KHz, with the FIFO and digital PLL technology, reduce Jitter to undetectable level.
Check List
T2 Transmitter 1pc
Remote Control 1pc
AC Adopter 1pc
CD-Rom 1pc
User Manual 1pc
Warranty Card 1pc
Specification
Digital Input Optical, Coaxial, PCM 44.1K-192K/16-24bit
USB input USB type B,3X Clock USB Asynchronous transmission,
support Win and Mac OS
Analogue Input RCA, max 2Vrms
Power Cord
Volume Electric volume, 0.5dB stepping, PW cut memory
Input Switch Switch button,PW cut memory
Transmitting Frequency 5.8GHz switchable
DC 5V 6.5mm，Max Current 1A
Bit depth 24 bit without compression
Max delay 10mS
Max support Receivers 8 pcs
Dimension 160*120*25MM
Front View
2
1) USB input indicator
2) SPDIF input indicator
3) Toslink input indicator
4) Analog input indicator
5) Input select button
6) Volume down
7) Volume up
Rear View
1) DC power input
2) Right channel Analog input
3) Left channel Analog input
4) SPDIF input
5) TOSLINK input
6) USB input, type B
3
Remote Control
Quick setup
1. Power on T2 Transmitter and R100/R20 0 Wir eless Amplifier
1) T2: Use its adapter to link its DC port with AV power supply.
2) R100/R200: Plug its power cord, and turn on the switch.
3) Pair T2 with R100 or R200.
2. Pairing T2 Transmitter with R100/R200 Wireles s Amplifier
1) T2: Long press the “INPUT” button (on front panel) for over 3 seconds, until 4 LED
indicators starts flashing (flash lasts for 60 seconds). It means T2 is ready for pairing.
Then release the “INPUT” button.
2) R100/R200: There is a “PAIRING” button at R100/R200 bottom chassis. When T2 is
ready for pairing, pin the “PARING” button until its front panel LED indicator stop flashing.
If it keeps flashing, it means not successfully paired, please pin the button again.
3) When T2 is in “Paring” status, user can continuously pair it with m ore Receivers.
4) A T2 Transmitter max pair 8pcs Receive rs (R100 /R200 can be mixed, total 8pcs).
5) After pairing, T2 is ready to be linked to audio source.
3. T2 setup
1) T2 can be linked to PC by USB input, CD/DVD player by SPDIF or TOSLINK, Analog
signal by Analog input.
2) Press the front panel “INPUT” button, to select “USB”, “TOSLINK”, “SPDIF”, “ANALOG”
according to the real input mode.
3) Then the whole system i s successfully setup.
4
Loading...