Quest Technical Sales and QTSHPWETH Users manual
HIGH POWER WIRELESS LINK KIT
®
FOR INTELLICENTER™, INTELLITOUCH
AND EASYTOUCH®
CONTROL SYSTEMS
INSTALLATION GUIDE
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
2
3
Technical Support
Phone: (800) 831-7133 - www.pentair.com
FCC Regulatory Safety Notice ...........................................................................3
High Power Wireless Link Kit Overview .............................................................4
High Power Wireless Link Kit Contents ..............................................................4
High Power Wireless Link Indoor Transceiver LEDs and Connectors ................5
High Power Wireless Link For ScreenLogic Interface Systems ..................6
Mounting Indoor Transceiver ..........................................................................6
Mounting Outdoor Transceiver .......................................................................8
Connect Transceiver Cable to the RS-485 COM Port .....................................8
IntelliCenter Control System
(Replacing Existing Wireless Antenna with HPW Link) .......................13-14
IntelliCenter Control System
(Without an Existing Transceiver) ...........................................................13-16
Contents
P/N 523445 Rev. A 1/2019
High Power Wireless Link Kit Installation Guide
FCC Regulatory Safety Notice
FCC non-modification statement:
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
FCC RF Exposure requirements:
Notice for High Power Wireless Link (FCC ID: 2AHWAQTSHPWETH -
HVIN/MODEL: HPW-WETHLINK: In order to comply with FCC/ISED RF Exposure
requirements, a minimum separation distance of 8 in (20 cm) must be maintained between the
equipment and all persons during normal operation.
Exigences de la FCC en matière d’exposition aux fréquences radio:
Remarquer: pour lien sans fil haute puissance (FCC ID: 2AHWAQTSHPWETH -
HVIN/MODEL: HPW-WETHLINK: Afin de respecter les exigences d’exposition RF de la FCC
/ ISED, une distance minimale de 20 cm doit être respectée entre l’appareil et toutes les
personnes en fonctionnement normal.
Canada - Innovation, Science and Economic Development (ISED)
(ISED: 21176-QTSHPWETH): The Control System and the High Power Wireless (HPW)
Link complies with RSS210 of ISED Canada (2019). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Innovation, Science and Economic Development
(ISED) Exempt RSSs. Operation is subject to the following: (1) This device may not cause
interference; and (2) This device must accept interference that may cause undesired operation
of the device.
Le dispositif est conforme à la licence Innovation, Science and Economic Development
(ISED) Canada. Le fonctionnement est soumis à la suivante. (1) Ce ne doit pas provoquer
d’interférences ; et (2) Cet appareil doit accepter les interférences qui peuvent causer un
mauvais fonctionnement de l’appareil.
Cet appareil numérique de classe B est conforme à la norme canadienne ISDE (RSP-100,
section 2.1) et Terminal Equipment Registrations (DC-01, Section 3.). Cet appareil numérique
de la classe B est conforme à la norme NMB-003 du Canada. Le terme «ISED» précédant
le numéro de certification / d’enregistrement signifie uniquement que les spécifications
techniques relatives à l’innovation, à la science et au développement économique ont été
respectées.
™
Instruction to user: The IntelliCenter
, EasyTouch® and IntelliTouch® Control System
High Power Wireless (HPW) Link has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. The
IntelliCenter, EasyTouch and IntelliTouch Control System High Power Wireless (HPW) Link
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this device does cause harmful interference to radio or television reception, which can be
determined by switching the device off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Note: The user is cautioned that changes and modifications made to the IntelliCenter,
EasyTouch and IntelliTouch
Control System without the approval of the manufacturer could
void the user’s authority to operate this equipment.
High Power Wireless Link Kit Installation Guide
4
Mounting hardware
(screws)
Outdoor
Transceiver
enclosure
Indoor transceiver
and base
Outdoor Cable
(white - 15 ft.)
NOTE (*): ID numbers
on Indoor and Outdoor
transceiver board must
match
Power Over Ethernet Module
(Outdoor hardware)
Cable (for connection to
ScreenLogic
®
Interface
Protocol Adapter
(purchased separately)
Ethernet Cable
(15 ft.)
Manual
Outdoor Transceiver
(Cable Restrainer)
AC Power Adapter
5
High Power Wireless Link Kit Overview
The High Power Wireless Link consists of an indoor and outdoor
902-928 MHz wireless transceiver. Note: The wireless transceivers ship
from the factory as a matched pair. The ID numbers on each transceiver
must be the same number to function correctly. If needed, the transceivers
must be replaced as a matched pair. For more information, call Customer
Support 800.831.7133.
Automation Control System: The High Power Wireless Link indoor and
outdoor transceiver provide a wireless connection between the Internet
and the IntelliCenter™, IntelliTouch
Center (or Power Center) located at the equipment pad which eliminates
hard wire connection from inside your home to the equipment pad.
Installation Guide
This Installation Guide provides installation instructions for the High Power
Wireless Link kit. For information about ScreenLogic Interface operation, refer
to the ScreenLogic Interface User’s Guide (P/N 520493).
High Power Wireless Link Kit Contents
The following items show are included in the kit:
Note:
ScreenLogic Interface Protocol Adapter and Cable (purchased separately)
®
or EasyTouch® Control System Load
High Power Wireless
Link PoE/Ethernet Cable
Bundle (P/N 544425)
High Power Wireless Link Kit
High Power Wireless Link Kit Installation Guide
High Power Wireless Link Indoor Transceiver LEDs and Connectors
1.75 in
Keep this side
clear of ALL
metal objects for
2 ft. (61 cm)
Model: HPW-WETHLINK
HVIN: HPW-WETHLINK
FCC ID: 2AHWAQTSHPWETH
ISED: 21176-QTSHPWETH
HIGH POWER
WIRELESS LINK
High Power Wireless
Indoor Transceiver LEDs
PWR: Green LED on: Power is on to the unit.
RX: Yellow LED indicates the unit is receiving data.
TX: Green LED indicates the unit is transmitting data.
Ethernet Port
IMPORTANT NOTICE: Be sure the
yellow ID label (8-digit ID number
XXXXXXXX) located on the front side
of the Indoor transceiver and the ID
number on the outdoor transceiver
circuit board are the same.
RS-485 Connector
(to Protocol Adapter,
ScreenLogic only)
Power Plug
socket
RS-485 Connector
(to Protocol Adapter,
ScreenLogic only)
High Power
Wireless Indoor
Transceiver and
base
ID number
(Outdoor transceiver)
High Power Wireless Link Kit Installation Guide
Loading...