Quest Technical Sales and QTS0000LINK User Manual

SCREENLOGIC® INTERFACE

WIRELESS CONNECTION KIT

FOR INTELLITOUCH® AND EASYTOUCH® CONTROL SYSTEMS

INSTALLATION GUIDE

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

SCREENLOGIC® INTERFACE Wireless Connection Kit Installation Guide

i

Tec hnical Support

Phone: [phone]
Web sites: visit www .pentairpool.com and www .staritepool.com

Contents

Overview ...........................................................................................................1

Wireless Connection Kit Contents ...................................................................... 1

Summary Installation Steps................................................................................2

ScreenLogic Interface Connection Diagram .......................................................3

Mount the Outdoor Wireless T r ansceiver and Connect to the

IntelliT ouch or EasyTouch Load Center .............................................................. 4

Connect the Indoor Wireless Transceiver to the ScreenLogic

Interface Protocol Adapter .................................................................................8

Connect the Indoor Wireless T ransceiv er to the ScreenLogic

Interface Protocol Adapter .................................................................................8

Cradle/Desk Mount the Indoor Wireless Transceiver ...........................................8

Wall Mount the Indoor Wireless Transceiver........................................................8

FCC Regulatory Safety Notice

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to pro vide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. Ho wev er , there is no guarantee that interf erence will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

• Modifications not expressly approved by the party responsible for FCC compliance
could void the user’s authority to operate the equipment.

Notice: In order to comply with FCC RF Exposure requirements, a minimum separation
distance of 8 in (20 cm) must be maintained between the equipment and all persons during
normal operation.

Industry Canada Statement

The device complies with industry Canada’s License Exempt RSSs. Operation is subject to the
following: (1) This device ma y not cause interference; and (2) This device must accept
interference that may cause undesired operation of the device.

Le dispositif est conforme à la licence d'Industrie Canada Exempt CNR. Le fonctionnement est
soumis à la suivante. (1) Ce ne doit pas provoquer d'interférences ; et (2) Cet appareil doit
accepter les interférences qui peuvent causer un mauvais fonctionnement de l'appareil.

This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la
classe B est conforme à la norme NMB-003 du Canada. The term “IC” before the certification /
registration number only signifies that the Industry Canada technical specifications were met.

SCREENLOGIC® INTERFACE Wireless Connection Kit Installation Guide

ScreenLogic® Interface Wireless Connection Kit Overview

r

The ScreenLogic® Interface Wireless Connection interf ace consists of an
indoor and outdoor wireless 902-928 MHz wireless transceiver .
Note: The wireless transceiv ers ship from the factory as a matched pair .
The ID numbers on each transceiver must be the same number to function
correctly . If needed, the tr ansceivers are replaced as a matched pair . F or
more information, call Customer Support [phone].

The indoor and outdoor transceivers provide a wireless connection
between the ScreenLogic Interface Protocol adapter and the IntelliTouch
or EasyT ouch® Control System Load Center located at the equipment pad.
This wireless connection eliminates the existing hard wire connection from
inside your home to the equipment pad.

In this Installation Guide

This Installation Guide provides installation instructions for the ScreenLogic
Interface Wireless Connection kit.

• For the ScreenLogic Interface system operating instructions, refer to the
ScreenLogic Interface User’ s Guide (P/N 520493)

Wireless Connection Kit Contents

The following items are included in the Wireless Connection kit:

•

One ScreenLogic Interface indoor wireless transceiver with AC power
adapter and 1 ft. long cable with attached plugs.

• One ScreenLogic Interface outdoor wireless transceiver with
10 ft. cable, enclosure and mounting hardware.

• ScreenLogic Interface Wireless Connection Installation Guide
(this manual).

NOTE (*): ID numbers
on Indoor and Outdoor
transceiver board must
match

Outdoor Cable
(white - 10 ft.)

Cable (for connection to
ScreenLogic
Protocol Adapter
(purchased separately)

®

Interface

SCREENLOGIC INTERFACE

ScreenLogic Interface
Protocol Adapter
(purchased separately)

1

®

®

®

Indoor transceiver and base

Indoor hardware

ScreenLogic Interface Wireless Connection Kit Contents

Outdoor
Transceive
enclosure

AC transformer

2X

2X

4X

4X

2X

Mounting hardware

SCREENLOGIC® INTERFACE Wireless Connection Kit Installation Guide

2

Summary Installation Steps

The ScreenLogic® Interface connection diagram on page 3 shows the
transceiver locations and connections. To install the ScreenLogic Interface
Wireless Connection kit:

• Mount the outdoor transceiv er antenna module near the IntelliT ouch
or EasyT ouch® Control System Load Center (see page 4 for
mounting instructions). Using the provided 10 ft. cable, connect the
transceiver to the COM port connector located in the IntelliT ouch or
EasyTouch Control System Load Center (see page 7).

• Connect the ScreenLogic Interface indoor wireless transceiver to the
ScreenLogic Interface Protocol adapter using the 12 in cable. Plug
the AC power adapter into an AC wall-outlet and into the wireless
transceiver unit to power up the unit (see page 8).

Note: ScreenLogic Interf ace Indoor Wireless Transceiver (Note: For optim um
performance, mount indoor transceiver upright in the cradle or on an indoor
wall).

Antenna location

®

Indoor Wireless T r ansceiver

LED Indicators Description:
PWR: Green LED on: P ower is on to the unit.

• PWR LED blinking: Not linked or lost link,
attempting to link or relink, no response.

• PWR LED b linking, TX and/or RX LED blinking:
not linked, attempting to link, getting responses.

• PWR LED on steady: Linked.

• PWR LED blinking: Lost link, Attempting to relink.
RX: Yellow LED indicates the unit is receiving data.

RS-485 Connector

(to Protocol Adapter)

TX: Green LED indicates the unit is transmitting data.

IMPORT ANT NOTICE: Be sure the
yellow ID label (9-digit ID number
XXXXXXXXX) located to the right of
the RS-485 connector on the front side
of the Indoor transceiver
enclosure and the ID number
on the ScreenLogic Interface Outdoor
Wireless transceiver are the same. See
page 1 for label location.

SCREENLOGIC® INTERFACE Wireless Connection Kit Installation Guide

ID number
(Outdoor transceiver)