Quest Engineering HPi110, HPi210 User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

User

Manual

Introduction ......................................1

CAUTION .................................................1

Safety Matters and Precautions ...................... 2

Simple Hanging Without Accessories .................. 3

SAFETY TIP ...............................................3

Kit Summary .....................................4

Table 1: Ready to use Rigging Kits .............................4

Kit QR1: Fixed Wall Mounting without Panning ........... 6

Mounting The Speaker & Rigging System .......................7

Setting The Angle Of The Cabinet .............................8

Kit QR2: Fixed Wall Mounting Tilt and Pan ..............9

Installation Spine ...........................................9

Installation of the Spine on the HPi110 .........................10

Setting the Angle of the Cabinet ...............................11

Kit QR3: Horizontal Two Speaker Array .................14

Mounting the Speaker & Rigging System. . . . . . . . . . . . . . . . . . . . . . . . 15

Kit – QR4: Horizontal Tri Speaker Array ................. 16

Mounting the Speaker & Rigging System. . . . . . . . . . . . . . . . . . . . . . . . 17

Kit – QR3X & QR4X: Extended Horizontal Arrays .......... 18

Controlling the Tilt of the Array ................................19

Attaching the Brackets to the Boxes ...........................21

Kit – QRUB: HPi110 U-Bracket. . . . . . . . . . . . . . . . . . . . . . . . 22

Horizontal Mounting of a Single Speaker ........................22

Mounting the Speaker & Rigging System. . . . . . . . . . . . . . . . . . . . . . . . 23

Configuring the Horn Flare Wave Guide for Horizontal Installation ...23

Summary of Separate Assemblies & Parts .............. 24

Separate Assemblies Table ...................................24

Spare Parts Table ..........................................25

Fasteners .................................................25

Contents

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

1

CAUTION

• Avoid locating the speaker box in high traffic areas where people may be injured on the

equipment and cords, or incur injury due to very high sound pressure level.

• Do not operate the unit for an extended period of time with the sound distorting. This is an

indication of a malfunction, which in turn can cause heat to generate within the speaker box and
possibly result in a fire.

• Have the rigging and installation fittings checked periodically by a competent technician or

rigging specialist. Failure to do so may result in corrosion or damage to the speaker system and
rigging leading to a life threatening situation.

• Check that all elevated work platforms or other height access devices (ladders etc) will safely

carry the weight of the products to be elevated and the weight of the installation personnel
before starting the job.

Introduction

The HPi110/210 speaker system is designed for live mobile and permanent installation using a
hardware system to cover every installation environment and array configuration. The QR (Quick
Rig) system has been developed so that the majority of the hardware rigging options are designed
to suit both the HPi110 and HPi210 models.

The HPi110/210 can be flown with weight rated high tensile eye bolts inserted into the many
box inserts but this can only be done following the standard rigging conventions understood by
licensed riggers.

Kits are available to facilitate simple and tidy installations while more sophisticated configurations
can be achieved by adding optional components to the basic kits.

Quest Engineering recommends that all available rigging and bracket options be reviewed for your
installation as a successful audio installation is greatly enhanced by correct speaker positioning.
The rigging options give a wide range of choices to direct the sound to where it is needed and
the prospect of very fine and accurate adjustments in all directivity planes. Numerous speaker
configurations for one, two or three speaker options are available with the HPi110/210 series and
flying an array of up to three boxes is possible with variable angles between the boxes.

The HPi110\210 QR system aims to be the most versatile rigging system in the world.

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

2

Safety Matters and Precautions

• Avoid installing the mounting hardware on unstable structures, such as on un reinforced walls or

ceiling members that are not intended for carrying extra weight.

• Refer all installation work to the dealer from whom the speaker was purchased. Installation for

flying speaker systems requires extensive technical knowledge and experience. The speaker
or rigging hardware may detach if not correctly installed, resulting in serious injury to anybody
below.

• Be sure to follow the flying instructions exactly as described. Do not take shortcuts during the

installation and flying process. Identify any possible risks or hazards before beginning the setup\
installation. Time and care should be taken so as not to expose yourself or other workers to
danger with unsafe practices.

• Check to confirm that suspension wires are strong enough, correctly terminated and sufficient to

carry the total load with at least a 4:1 safety rating.

• The connectors of the suspension wires and belts must be securely linked with those of the

speaker or rigging hardware.

• All parts and components (such as enclosures, metal pieces, and screws) must be free from any

damage, cracks and\or corrosion.

• Be sure to use screws supplied with the optional flying hardware when installing any mounting

hardware or the speaker itself.

• Install the unit only in a location that can structurally support the weight of the unit and the

mounting bracket.

• When hanging a rigged array, be sure that at least two persons are available to install the unit.

Failure to do so could result in personal injury.

• Do not use other methods than those specified to mount the speaker boxes.

• Use nuts and bolts that are appropriate for the ceilings or wall’s structure and composition.

• Tighten each nut and bolt securely. Ensure that the hardware has no loose accessories.

• Use only the specified mounting brackets. No warranty is provided due to damage resulting from

a failure of after-market accessories.

• Do not mount the unit in locations exposed to constant excessive vibration. Fittings on the

mounting bracket or fly-ware may become loose causing components to detach and cause injury
below.

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

3

Simple Hanging Without Accessories

The structure and construction of the HPi110/210 allow for a variety of hanging possibilities.

Both the HPi110 and HPi210 include 9 x M10 lifting points, and as well as a pole mount plate, to
bring maximum flexibility even without additional accessories.

All points are either straight on the metallic handle or connected to an internal metal brace.

When hanging the box with eye bolts, rigging conventions dictate that the box must be attached
by two independent fixation points and both points must be able to carry the weight of the flown
installation plus the mandated safety factor.

Each Side:
2 points on the
aluminium handle.

Top 2 points

SAFETY TIP

On both HPi110 and HPi210, the safest
place to hook a safety link is to the
aluminium handle; particularly the rods
that join the handle to the speaker (as
shown here).

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

4

Kit Summary

The QR System includes various mounting options and components for the HPi 110/210. Whether
your requirements are for touring or highly specific installations, there is a perfect solution readily
available. Several kit options have been designed which include everything required for most
applications.

Name &
Reference

Application In the Kit Kit Illustration

Kit QR1

Order Ref:
ACHPiQR1

• 1 Speaker

• Wall Mounting

• Tilt (0-30o)

• No Panning

• Wall-Mount

Assembly (fixed)

• i-Spine

• Quick pin 8x50

• Screws (2x M10)

Kit QR2

Order Ref:
ACHPiQR2

• 1 Speaker

• Wall Mounting

• Tilt (0-30o)

• Full Pan (-/+ 75o)

• Wall-Mount

Assembly
(swivelling)

• i-Spine

• Quick Pin 8 x 50

• Screws (2x M10)

Kit QR3

Order Ref:
ACHPiQR3

• 2 Speakers

• Hanging

• Variable Angle between

speakers

• Vertical Tilt (-10/+20˚)

• Hanging Plate 2

• Screws (4x M10)

Kit QR3X

Order Ref:
ACHPiQR3X

• 2 Speakers

• Hanging

• Variable angle between

speakers

• Extra vertical Tilt
(+25/+45˚)

• Hanging Plate 2

• Extension Arm

Assembly

• Screws (4x M10)

Kit QR4

Order Ref:
ACHPiQR4

• 3 speakers

• Hanging

• Variable angle between

Speakers

• Vertical Tilt (+15/+20˚

approx)

• Hanging Plate 3

• Screws (6x M10)

Table 1: Ready to use Rigging Kits

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

5

Table 1: Ready to use Rigging Kits (cont.d)

Name &
Reference

Application In the Kit Kit Illustration

Kit QR4X

Order Ref:
ACHPiQR4X

• 3 Speakers

• Hanging

• Variable angle between

speakers

• Extra vertical Tilt
(+25/+45˚ approx)

• Hanging Plate 3

• Extension arm

assembly (x2)

• Screws (6x M10)

Kit QR5

Order Ref:
ACHPiQR5

• 2 speakers

• Vertical array

• Hanging

• Variable tilt of both

speakers

• t-Spine assembly

(includes 1 quick pin +
2M10 screws)

• i-Spine (includes 1

quick pin + 2M10
screws)

• Vertical link bar

HPi110
bracket

Order Ref:
ACHPiWB110

• 1 speaker

• Horizontal bracket

• Mounting on walls/ truss

• Variable angulations (-15˚
to 90˚ in both directions)

• Bracket frame

• Bracket bottom plate

• M6 flat head (x1)

• M10 flat head (x2)

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

6

The QR1 kit

(standard for fixed

wall mounting

installations) comes

complete and

assembled, with the

right screws and

bolts to install a

single HPi110.

The installation Spine (i-Spine) offers

a more elegant solution for permanent

installations. The row of holes at the rear

of the spine allows for vertical tilt when

wall-mounted.

The i-Spine comes with an M8x50 custom

Quick Pin (Q-Pin) as well as a pair of long

M10 counter sunk screws.

Ordering reference:
ACHPiATS

Option Note for QR-1

(Available as a separate component)

The touring Spine (t-Spine) is
recommended for a precise and easy
hanging setup of the speaker when
used when flying a single speaker.

The holes, on each side, allow for a
5o stepped tilt of the cabinet [from

-15˚ to +45˚] Only one rated shackle

is necessary to use the Spine in
most applications (a quick-pin is also
included with the t-Spine).

The t-Spine can also be used as part
of a more complex rigging system.

Primary applications include:

• Wall Mount applications where tilt is

not needed

• Vertically Arraying 2 Speakers

Kit QR1: Fixed Wall Mounting without Panning

Name & Reference Application In the Kit

Kit QR1

Order Ref: ACHPiQR1

• 1 speaker

• Wall Mounting

• Tilt (0-30o)

• No panning

• Wall-Mount assembly (fixed)

• Installation Spine

• Quick pin 8x50

• Screws (2x M10)

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

7

Mounting The Speaker & Rigging System

Installation of the Spine on the HPi110

NOTE: The 2 x M10 bolts supplied with both the i-Spine and t-Spine should replace the previously
installed screws in the speaker. The M10 bolts are designed with a longer thread which provides
increased strength and security to the system.

Remove the 2 top
screws that are
installed in the speaker
then insert the lip of
the Spine to grab the
casing handle.

1

Swing it flat on the
top of the speaker.

2

Bolt in and secure
(using Loctite or similar
fastener securing
compound) the Spine
onto the speaker with
the 2 x M10 bolts
included.

3

Installing an HPi110 becomes incredibly easy
with the QR wall-mounting system.

Once the spine has been installed (as
described above) install the wall-mount as
follows:

1. Bolt the wall mount assembly (without
the speaker attached) onto the wall.

2. Lift the speaker (now installed with
Spine) and hook it onto the wall-mount.
The wall-mount is designed to safely
support the weight of the box from this
point.

3. Set the angle by sliding the quick-pin
into the right hole (see next section for
angles).

HPi110 with

i-Spine

Fixed hook

assembly

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

8

Setting The Angle Of The Cabinet

Once the speaker has been mounted correctly, the angle at which the speaker will be fixed can be
adjusted by fitting the Q-Pin into the correct hole. Four angles are available:

HPi110 with Kit QR1 Standard

HPi110 with Kit QR1 Long Side Plates

7.5 degrees 15 degrees 30 degrees0 degrees

The standard kit offers the possibility to hang

a speaker at 0˚ and 7.5˚.

If extra tilt (15˚ or 30˚) is needed, optional

extension plates can be purchased separately
and inserted in the wall-mount assembly.

Order Reference:
ACHPiEX2

Option Note for QR-1

(Available as a separate component)

• Take the medium side plates off the

assembly by removing the bolts.

• Use the same bolts, washers and

nuts for the long plates (all bolts,
washers and nuts should be re-used)

• Long side plates can be ordered

for adding ‘x’ of additional distance
from the wall. (sold separately)

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

9

QR2 Assembled Kit
(shown with the i-Spine)

HPi110 with the
QR2 Kit

Installation Spine

The installation Spine (i-Spine) offers a more elegant solution for permanent installations. The row
of holes at the rear of the spine allows for vertical tilt when wall-mounted.

The i-Spine comes with an M8x50 custom Quick Pin (Q-Pin) as well as a pair of long M10 counter
sunk screws.

The kit QR1 (standard kit for fixed wall mounting installations) comes complete and assembled,
with the right screws and bolts to install a single HPi110.

Kit QR2: Fixed Wall Mounting Tilt and Pan

Name & Reference Application In the Kit

Order Ref: ACHPiQR2

• 1 speaker

• Wall Mounting

• Tilt (0-30˚)

• Full Pan (-/+ 75˚)

• Wall-Mount assembly (swivelling)

• i-Spine

• Quick pin 8x50

• Screws (2x M10)

Ordering reference:
ACHPiEX2

Option Note for QR-2

(Available as a separate component)

• Take the medium side plates off the

assembly by removing the bolts.

• Use the same bolts, washers and

nuts for the long plates (all bolts,
washers and nuts should be re-used)

• Long side plates can be ordered

for adding ‘x’ of additional distance
from the wall. (sold separately)

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

10

Installation of the Spine on the HPi110

NOTE: The 2 x M10 bolts supplied with both the i-Spine and t-Spine should replace the
previously installed screws in the speaker. The M10 bolts are designed with a longer thread
which provides increased strength and security to the system.

Primary Applications Include:

• Wall Mount applications where tilt is

not needed

• Vertically Arraying 2 Speakers

The touring Spine (t-Spine) is
recommended for a precise and easy
hanging setup of the speaker when
used when flying a single speaker.

The holes, on each side, allow for a 5o
stepped tilt of the cabinet [from -15o

to +45o]

Only one rated shackle is necessary
to use the Spine in most applications.
(A quick-pin is also included with the
t-Spine)

The t-Spine can also be used as part of
a more complex rigging system.

Ordering reference:
ACHPiATS

Remove the 2 top
screws that are
installed in the speaker
then insert the lip of
the Spine to grab the
casing handle.

Swing it flat on the
top of the speaker.

Bolt in and secure
(using Loctite or similar
fastener securing
compound) the Spine
onto the speaker with
the 2 x M10 bolts
included.

1

2 3

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

11

Installing an HPi110 becomes easy with the
QR wall-mounting system.

Once the spine has been installed (as
described above) install the wall-mount as
follows:

1. Bolt the wall mount assembly (without
the speaker attached) onto the wall.

2. Lift the speaker (now installed with
Spine) and hook it onto the wall-mount.
The wall-mount is designed to safely
support the weight of the box from this
point.

3. Set the angle by sliding the quick-pin
into the right hole (see next section for
angles).

HPi110 with

i-Spine

Fixed hook

assembly

HPi110 with Kit QR2 Standard

HPi110 with Kit QR2 Long Side Plates

7.5 degrees 15 degrees 30 degrees0 degrees

Setting the Angle of the Cabinet

Once the speaker has been mounted correctly, the angle at which the speaker will be fixed can be
adjusted by fitting the Q-Pin into the correct hole. Four angles are available:

The standard kit offers the possibility to hang

a speaker at 0˚ and 7.5˚.

If extra tilt (15˚ or 30˚) is needed, optional

extension plates can be purchased separately
and inserted in the wall-mount assembly.

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

12

Adjusting and Locking Horizontal Pan.

The advantage of the swivelling assembly is the ability to set the pan angle from -75˚ to +75˚.

The cabinet can be locked in position by tightening the screw located on top of the pivot axis of the
rigging assembly.

Swivel of a HPi110 mounted on a kit QR2

Tighten the top screw

2

Turn the Cabinet

1

If more vertical angle is required, two optional
side plate can be inserted in the assembly
(replacing the medium plates), and give the
ability to either set the speaker closer to the
wall, or reach a down tilt of 15 or 30 degrees.

Exploded view of swivelling wall mount

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

13

Installation Examples

Tilt = 0˚

Pan=-30˚

Standard medium side plates
replaced by spacers (the
speaker is looser to the wall)

Tilt = 7.5˚

Pan=+30˚

Standard medium side plates

Tilt = 30˚

Pan=+45˚

Standard medium side plates
replaced by long plates

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

14

Kit QR3: Horizontal Two Speaker Array

The QR3 kit allows for a pair of HPi110 or HPi210 speakers to be hung horizontally with the utmost
of ease. The top plate has several fastening positions which provide several options for speaker
positioning providing complete control over the dispersion of audio.

The QR3 kit comes complete and assembled, with the right screws and bolts to install a pair of
HPi110 speakers.

Name & Reference Application In the Kit

Order Ref: ACHPiQR3

• 2 speakers

• Hanging

• Variable Angle Between Speakers

• Vertical Tile (-10/+20˚)

• Dual speaker hanging plate

• Screws (4x M10)

Kit QR3

HPi110 Installed with QR3 Kit

Option Note for QR-3 (Extended Horizontal kit – QR3X)

The QR3X includes an extension arm which increases the

array’s tilt to achieve angles between 15˚ up to 35˚.

For more information on the QR3X kit, please see The
section on Extended Horizontal Arrays.

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

15

Mounting the Speaker & Rigging System

The hanging plate for 2 speakers allows for 3 sets of angles.

For application where wider dispersion is required, the 2 speakers can be angled at 10˚ or 20˚ in
addition to the standard 30˚ when the speakers are positioned side by side.

Please ensure that regardless of the angle, each speaker is secured with 2 x M10 screws.

Installation Examples

2 HPi110 in a dual horizontal array : kit QR4 ; angle=30˚ (Standard)

2 HPi110 in a dual horizontal array : kit QR4 ; angle=40˚

2 HPi110 in a dual horizontal array : kit QR4 ; angle=50˚

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

16

Kit – QR4: Horizontal Tri Speaker Array

The QR4 kit allows for three HPi110 or HPi210 speakers to be hung horizontally with the utmost of
ease. The top plate has several fastening positions which allowing you to adjust the angles of the
left and right speakers providing complete control over the dispersion of audio.

The QR4 kit comes complete with the right screws and bolts to install three HPi110 speakers.

Name & Reference Application In the Kit

Order Ref: ACHPiQR3

• 3 speakers

• Hanging

• Variable Angle Between Speakers

• Vertical Tile (-15/+20˚)

• Two speaker hanging plates

• Screws (6x M10)

HPi110 Installed with QR4 Kit

QR4 Kit

Option Note for QR-4 (Extended Horizontal kit – QR4X):

The QR4X includes an extension arm which increases the

array’s tilt to achieve angles between 15˚ up to 35˚.

For more information on the QR4X kit, please see The
section on Extended Horizontal Arrays.

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

17

Mounting the Speaker &
Rigging System

The hanging plate for 3 speaker allows for 3
sets of angles. Installation Examples

For application where wider dispersion is
required, the 3 speakers can be angled at 15
o or 20o delivering an extremely simple to
install wide dispersion array solution.

Please ensure that regardless of the angle,
each speaker is secured with 2 x M10 screws.

Mounting the hanging plate:

1. Remove the 2 M10 screws at the top of
each speaker.

2. Place the hanging plate on top of the 3
speakers and align to the desired angles.

3. Bolt in the 6 M10 x35 counter sunk
screws included in the kit. (Add Loctite
to give additional fastener security)

Top view of 3 x HPi110’s installed with the QR4 kit.

Installation Examples

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

18

Kit – QR3X & QR4X: Extended Horizontal Arrays

The QR3X and QR4X kits include an extension arm which increases the array cluster’s tilt to

achieve angles between 15˚ and 35˚.

Name & Reference Designed For: QR-3 Kit Includes:

Order Ref: ACHPiQR3X

• 2 speakers

• Hanging

• Variable Angle Between Speakers

• Extra Vertical Tilt

• (-25/+45 o)

• Dual Speaker Hanging Plate

• Screws (4 x M10)

QR4X Kit

HPi110 Installed with QR4X Kit

Name & Reference Designed For: QR-4X Kit Includes:

Order Ref: ACHPiQR4X

• 3 speakers

• Hanging

• Variable Angle Between Speakers

• Extra Vertical Tilt (-25/+45 o)

• Tri speaker hanging plate

• Screws (6 x M10)

HPi110 Installed with QR3X Kit

QR3X Kit

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

19

Controlling the Tilt of the Array

The extension arm provides the possibility of giving the whole assembly extra tilt of up to 35 degrees.

Angles with standard hanging plate:

Angles with extension arm:

-15˚ -20˚ -25˚ -30˚ -35˚

+10˚ +5˚ 0˚ -5˚ -10˚

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

20

Kit – QR5: Vertical Dual Speaker Array

Name & Reference Application In the Kit

Order Ref: ACHPiQR5

• 2 speakers (HPi110 only)

• Vertical Hanging

• Variable Tilt for each

Speaker

• t-Spine assembly (includes 1 quick pin +

2M10 screws)

• i-Spine (includes 1 quick pin + 2M10

screws)

• Vertical Link Bar

The QR5 kit provides a specialised dual
speaker vertical array solution. The uniquely
designed link bar allows for two speakers to
be vertically hung from the same point with
independent control over the angle of each
cabinet.

The tilt angle of the vertical hang is
determined by the shackle location on the
Touring Spine and the location of the locking
pin located at the base of the hanging bar and
the tilt angle locators on the installation spine
connected to the lower box.

If further rake angle is required, control is
possible by attaching a guy wire to the lower
box at one of the two box insert points with a
rated eye bolt.

QR5 Kit

HPi110 Installed with QR5 Kit

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

21

HPi110 with t-Spine
and vertical link bar

The angle

shown

is a 15˚

setting.

Attaching the Brackets to the Boxes

Hook the vertical link bar at the back
of the top speaker.

1

Bolt the 2 M10 screws back in place. That
will lock the vertical bar onto the speaker.
Make sure the screws are tight.

2

Hook the bottom speaker at the end of the
vertical link bar. (This can be done before
or after the top cabinet is flown)

3

Select the angle of the second cabinet
(compare to the first one) by sliding the
quick pin in the slots (operation similar
to selecting the angle for the Wall Mount
assemblies).

4

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

22

Kit – QRUB: HPi110 U-Bracket

Horizontal Mounting of a Single Speaker

Name & Reference Designed For: Kit Includes:

Order Ref: ACHPIWB110

• 1 speaker

• Horizontal bracket

• Mounting on walls/ truss

• Variable angulations
(-15˚ to 90˚ in both directions)

• Bracket frame

• Bracket bottom plate

• M6 flat head (x1)

• M10 flat head (x2)

The QR-UB is a horizontal single speaker
mounting bracket designed for mounting
a single HPi110 in a permanent low profile
horizontal installation. The bracket can also
be attached to a scaffold clamp for fixing to
truss in a mobile installation.

The HPi110 bracket offers two ranges of

angles (from -15 to +90˚).

Installation option #1 offers exact angulations

by 22.5˚ Steps: -15-0˚

The correct tilt angle is determined by the
location of fixing bolts that are inserted
through the bracket plate holes and into the
internal threaded inserts in the speaker box
casing.

Installation option #2 more angle options
are achieved by reversing the bracket and
threading the fasteners through the half
moon slot holes. This gives the installer the
opportunity to set very precise custom angles
by installing the bolt fasteners through the
slot holes and tightening the fasteners when
the box is set at the desired angle.

QRUB Kit

HPi110 Installed

with QRUB Kit

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

23

Mounting the Speaker & Rigging System

Mounting the QR-UB bracket

Configuring the Horn Flare Wave Guide for Horizontal Installation

The HPi110 is equipped with a rotatable asymmetric horn flare which can be used in harmony
with the QR-UB bracket to ensure that acoustic dispersion is accurately configured to suit the
requirement of the installation.

For more details, consult the HPi 110 owner’s manual to set the horn flare dispersion to the
horizontal with the desired horn coverage dispersion.

Remove the front grill and unfasten the four screws holding the horn flare. The section of the horn
flare with the “Q” is the wide dispersion side and the narrow area of the horn is the long throw and
must be set to the ceiling side of the installation (if that is the area required for the HF long throw)

When reattaching the horn flare, do not over tighten the screws.

Remove the
top hat from
the HPi110
as well as the
2 screws at
the top of the
speaker.

1

Replace the
top hat plate
with the HPi110
bracket Bottom
plate.

2

Screw in with
3 of the 4
screws you just
unscrewed from
the cabinet

3

Insert the
bracket over
the speaker

4

Bolt it on
the bottom
plate (use
a long M6
screw in the
packaging)

5

Choose your angle by placing the top screws (included in the
kit) in the right holes through the rotation plate.

6

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

24

Name & Reference Application In the Kit Kit Illustration

Wall Mount Fix Hook
Assembly

Order Ref:ACHPiAFH

• 1 speaker

• Wall Mounting

• Tilt (0-30˚)

• No panning

Needs to be operated
with matching Spine

• Wall Plate

• Medium side plates

(standard)

• Fixed hook

• 8x shoulder bolts

• 16x washers

• 8x nylock nuts

Wall Mount Swivelling
Assembly

Order Ref:ACHPiASW

• 1 Speaker

• Wall Mounting

• Tilt (0-30˚)

• Full Pan (-/+ 75˚)

Needs to be operated
with matching Spine

• Wall Plate

• Medium side plates

(standard)

• Swivel male part

• Swivel female part

• 8x shoulder bolts

• 16x washers

• 8x nylock nuts

• 1x M8 round-head screw

Extension arm
Assembly

Order Ref:ACHPiAEA

• Extra tilt for

hanging plates
(horizontal
arrays)

• Extension arm

• 2x shoulder bolts

• 2x nylock nuts

Installation Spine
Assembly

Order Ref:ACHPiAIS

• All kits using the

installation spine

• Wall mount

• Vertical array

• i-Spine

• 1x M8x50 lock pin

• 2x M10 screws

Touring Spine
Assembly

Order Ref:ACHPiATS

• Stand alone

• All kits using the

touring spine

• Wall mount

• Vertical array

• t-Spine

• 1x M8x50 lock pin

• 2x M10 screws

Summary of Separate Assemblies & Parts

Separate Assemblies Table

HPi110 & HPi210

Quick Rig (QR) Systems

User Manual

HPi110 & HPi210 Quick Rig (QR) Systems

25

Name &
Reference

Kit Illustration

ACHPiIS

ACHPiTS

ACHPiWP

ACHPiFH

ACHPiSW1

ACHPiSW2

ACHPiEX1

ACHPiEX2

Name &
Reference

Kit Illustration

ACHPiEX2

ACHPiHP2

ACHPiHP3

ACHPiEA

ACHPiBP

ACHPiLB

Spare Parts Table

HFSB810 M6 – 8x10 shoulder bolt

HFW8Z 8mm washer zinc plated

HFNUT6N M6 nylock nut

HFRH820 M8 x 20 round-head hex

HFCS1035 M10 x30 countersunk hex

Fasteners

www.questaudio.net

Quest Engineering Pty Ltd

86 Derby St. Pascoe Vale VIC 3055

Ph 613 9354 9133 | Fax [phone]