How it Works
Qubino
Loading...
FLUSH 1 RELAY
USER MANUAL
72 pgs5.88 Mb0
Table of contents
Loading...

Qubino FLUSH 1 RELAY USER MANUAL

EN.
2
Table of contents
Where To Buy.................................................................................................................................. 4
1. Introduction ................................................................................................................................ 4
2. Use Cases .................................................................................................................................... 5
2.2. Installation examples where Flush 1 Relay is installed behind a power socket – for
2.3. Installation examples where Flush 1 Relay is installed behind a power socket – for
2.5. Installation examples where Flush 1 Relay is installed in combination with temperature
3. Qubino Flush 1 Relay Advantages and Highlights ..................................................................... 15
4. Installation ................................................................................................................................ 19
5. Device Information and Support............................................................................................... 43
6. Electrical Diagram (110 - 240VAC, 24VDC) ............................................................................... 45
7. Adding the device to a Z-Wave network (Inclusion) ................................................................. 46
8. Removing the device from a Z-Wave network (Exclusion) ....................................................... 47
9. Associations .............................................................................................................................. 48
10. Technical Terms for Switches ................................................................................................. 49
11. Configuration Parameters ....................................................................................................... 50
EN.
3
12. Compatibility with Z-Wave Gateways (hubs) ......................................................................... 59
13. Technical Specifications .......................................................................................................... 60
14. Package Contents .................................................................................................................... 62
15. Z-Wave Command Classes ...................................................................................................... 63
16. About Qubino .......................................................................................................................... 67
17. Safety Information .................................................................................................................. 69
18. Flush 1 Relay - Available Frequencies ..................................................................................... 70
19. Important Disclaimer .............................................................................................................. 71
20. Warning ................................................................................................................................... 71
21. Regulations.............................................................................................................................. 71
EN.
4

Where To Buy

To find your nearest Qubino dealer visit: http://qubino.com/where-to-buy/

1. Introduction

The Flush 1 Relay controls on/off function for one electrical device. It measures power consumption of the connected device and can be paired with a digital temperature sensor (sold separately). It supports push-button/momentary switches and toggle switches (default).
The connection of a digital temperature sensor means you can create complex scenes and control any device relative to a set temperature range. The Qubino Flush 1 Relay also acts as a Z-Wave repeater to improve the range and stability of the Z-Wave network.
EN.
5

2. Use Cases

The Flush 1 Relay can be used in many different scenes, which can help make your life more comfortable. We have prepared a few of them for you so you can get an idea for your next smart home project. Of course, there are countless of other options for how to use Qubino Flush 1 Relay to remotely control devices via your smartphone.
Qubino devices are installed into flush mounting boxes behind the switches. You can see some examples below:
For more information on how to install your device, please refer to the Installation chapter.
There are different switch types in different countries, as for example:
Further in the document you will notice that all the use cases show the USA example switch type. Note that the product works in the same way with EU switch type, ITA/Brazil type, UK type etc.
EN.
6

2.1. Installation examples where Flush 1 Relay is installed behind a wall switch

• Remotely control lights
• Remotely control ceiling fans
• Remotely control wall-mounted fans
• Remotely control domestic hot water
tanks
EN.
7
• Remotely control infrared – heater
• Remotely control wall mounted infrared
heating panel
• Remotely trigger different scenes with two
additional inputs (I2, I3) – for example scene 1: turn on all the lights in the house, scene 2: turn off all the lights in the house
EN.
8

2.2. Installation examples where Flush 1 Relay is installed behind a power socket – for switching device on/off and measuring power consumption of the connected device

There are different sockets types in different countries, as for example:
Further in the document you will notice that all the use cases show the USA example socket type. Note that the product works in the same way with EU switch type, ITA/Brazil type, UK type etc.
• Remotely control an oven connected to a
power socket
• Remotely control an iron connected to a
power socket
EN.
9
• Remotely control a fan connected to a
power socket
• Remotely control floor lights connected
to a power socket
• Remotely control microwave oven
connected to a power socket
• Remotely control television connected to
a power socket
EN.
10
• Remotely control computer connected to a
power socket

2.3. Installation examples where Flush 1 Relay is installed behind a power socket – for measuring power consumption of the connected device

• Remotely measure power consumption of
refrigerator connected to a power socket
EN.
11

2.4. Installation examples where Flush 1 Relay is installed in electrical box

• Remotely control 24VDC irrigation sprinkle
valves.
• Remotely control 240/110VAC or 24VDC
irrigation sprinkle valves.
• Remotely control sanitary hot water
recirculation pumps and remotely measure temperature of the sanitary hot water (*The temperature sensor is sold separately - for more info, check Qubino catalogue. Product ordering code: ZMNHEA1)
• Remotely control pool recirculation
pumps and measure pool water temperature (*The temperature sensor is sold separately - for more info, check Qubino catalogue. Product ordering code: ZMNHEA1)
EN.
12

2.5. Installation examples where Flush 1 Relay is installed in combination with temperature sensor

• Remotely measure room temperature with
connected temperature sensor (*The temperature sensor is sold separately - for more info, check Qubino catalogue. Product ordering code: ZMNHEA1)
EN.
13

2.6. Additional features of Flush 1 Relay which can make your life easier

• Do you worry that your irrigation system
can expose your garden to flooding?
• Sometimes your Z-Wave gateway (hub)
can stop working while you’re away from
home (no internet connection, power outage, etc). If you have an irrigation scene scheduled, your gateway (hub) might not send an OFF command to your irrigation system, leaving your garden flooded and water bill more expensive
than you’d like. The Flush 1 Relay offers
the option to set the timing for irrigation for a specific amount of time internally; it then automatically stops watering, completely independent of your gateway’s (hub’s) commands.
For the 24VDC use case, please check the chapter above.
• Do you often forget to turn off devices
when you leave your home, like lights in the basement or attic?
• The Flush 1 Relay can automatically turn
devices/lights on or off after a set period
of time (when you’re away from home).
For example, the light will automatically
turn off if it’s been on for 8 hours, let’s
say. This function is independent of other scenes and gateway (hub) commands.
EN.
14
• Do you know how much energy you
consume?
• The Flush 1 Relay monitors and reports
energy consumption of connected devices in real time to your smart home app (your gateway (hub) needs to support this feature). Know how much power your light, domestic water tank, iron, etc, is using.
• Want to control other devices in your Z-
Wave network with the Flush 1 Relay?
• Connect the Flush 1 Relay with other
devices in your network to remotely and automatically trigger another Z-Wave device. And have other Z-Wave devices trigger your Qubino Flush 1 Relay.
Where To Buy
To find your nearest Qubino dealer visit: http://qubino.com/where-to-buy/
EN.
15

3. Qubino Flush 1 Relay Advantages and Highlights

3.1. Advantages

• The Qubino Flush 1 Relay allows the easiest and quickest installation possible. Because
of its small size, it fits smoothly in even the smallest, most shallow and most crowded flush mounting boxes, which are stuffed with lots of electrical cables and where every
millimetre counts. All this is possible because the Qubino Flush 1 Relay is the smallest Z­Wave switch in the world.
• The Qubino Flush 1 Relay has the option to connect a temperature sensor*, through
which users can monitor the ambient air or water temperature. It’s the only Z-Wave switch in the world which offers this option. With a connected sensor, the user can monitor accurate measurements of the room temperature, pool water temperature, etc., and remotely change conditions as desired. Qubino relay, along with the temperature sensor, is connected directly to the power supply. Install it and forget it – no need to worry about dying batteries, like with battery-powered sensors.
*The temperature sensor is sold separately - for more info, please see Qubino catalogue. Product ordering code (model number): ZMNHEA1
ⓘ Please do not put the temperature sensor directly into the water! The temperature
sensor is designed to measure the water temperature by being mounted to the water pipe.
EN.
16
• The Qubino Flush 1 Relay is the only Z-Wave switch in the world that has two additional
inputs (I2, I3), which enable triggering of different scenes. The user does not need to buy additional devices for setting various scenes. For example:
o Switch connected to input I2: Welcome Home – turn on all the lights in the
house
o Switch connected to input I3: Leaving Home – turn off all the lights in the house
• Qubino guarantees 100% device quality. Such high quality can be delivered because
every Qubino goes through rigorous quality control standards throughout the production process. Every device has a unique serial number and a part number, which are assigned to the device only after it goes through a strict testing procedure.
EN.
17
• By scanning the QR code on the back of your Qubino device, the serial and part numbers
will be automatically copied on your mobile phone; they also provide direct access to Qubino’s technical support team. The serial and part numbers of your device are given automatically every time you open an inquiry with our support team: this instantly shares the relevant device information we need to provide the best technical support possible. For details, please see the Device Information and Support chapter.
• The Qubino Flush 1 Relay is engineered and manufactured in the EU, and contains only
the highest quality components.
EN.
18
• The Qubino Flush 1 Relay is certified by an independent European Institute and has CE,
FCC, LVD and EMC certificates to ensure the highest safety standards.

3.2. Highlights

• Remote (via smartphone or PC) and local on/off control of bulbs and other electrical
devices
• Works with push-button (momentary switch) and toggle switch or you can install it
behind power sockets
• Capable of measuring the power consumption of the connected device in real time via
smartphone, which allows you to save on electricity bills*
• Features one of the easiest and quickest installations of devices of this kind; fits in even
the smallest flush mounting boxes
• Saves and restores the last status after a power failure
• Supports auto-inclusion mode for quick set up
• Can automatically turn devices on and off after a set period of time (helpful when you’re
away from home, for example) *
• Supports additional parameters for expert users, which allows for advanced
configuration*
• Acts as a signal repeater which improves the range and stability of your Z-Wave network
• Can be used to remotely control and trigger other devices in your Z-Wave network
*Your gateway (hub) needs to support advanced configuration and parameter input if you wish to use this feature
EN.
19

4. Installation

Before installing the device, please read the following carefully and follow the instructions exactly:
ⓘ Danger of electrocution!
Installation of this device requires a great degree of skill and may be performed only by a licensed and qualified electrician. Please keep in mind that even when the device is turned off, voltage may still be present in the device’s terminals.
EN.
20
ⓘ Note!
Do not connect the device to loads exceeding the recommended values. Connect the device exactly as shown in the provided diagrams. Improper wiring may be dangerous and result in equipment damage.
Electrical installation must be protected by directly associated overcurrent protection fuse 10A, gG or Time lag T, rated breaking capacity 1500A (ESKA 522.727) must be used according to wiring diagram to achieve appropriate overload protection of the device. The fuse must be installed in fuse holder type: Adels contact 503Si/1 DS according to the standard IEC60669-2-
1.
EN.
21

4.1. Installing the device behind a light switch

The installation process, tested and approved by professional electricians, consists of the following simple steps:
Step 1 – Turn OFF the fuse:
• To prevent electrical shock and/or equipment damage, disconnect electrical power at
the main fuse or circuit breaker before installation and maintenance.
• Be aware that even if the circuit breaker is off, some voltage may remain in the wires —
before proceeding with the installation, be sure no voltage is present in the wiring.
• Take extra precautions to avoid accidentally turning the device on during installation.
EN.
22
Step 2 – Installing the device:
• Connect the device exactly according to the diagrams shown below
Before Qubino installation:
Loading...
+ 50 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use