The area next to the indicator will identify the specific information and make any
references necessary.
The area next to the indicator will identify the specific information and make any
references necessary.
1.0 Conventions
The following section outlines the conventions used within the document, where
convention is deviated from the deviation takes precedence and should be followed. If
you have any question related to the conventions used or clarification of indicated
deviation please contact Quatech Sales or Wireless Support.
1.1 Terminology
Airborne Enterprise Device Server and AirborneDirect Enterprise Device
Server is used in the opening section to describe the devices detailed in this
document, after this section the term module will be used to describe the
devices.
1.2 Notes
A note contains information that requires special attention. The following
convention will be used. The area next to the indicator will identify the specific
information and make any references necessary.
1.3 Caution
A caution contains information that, if not followed, may cause damage to the
product or injury to the user. The shaded area next to the indicator will identify
the specific information and make any references necessary.
1.4 File Format
These documents are provided as Portable Document Format (PDF) files. To
read them, you need Adobe Acrobat Reader 4.0.5 or higher. For your
convenience, Adobe Acrobat Reader is provided on the Radio Evaluation Kit CD.
Should you not have the CD, for the latest version of Adobe Acrobat Reader, go
to the Adobe Web site (www.adobe.com).
100-8080-110 8/11/2009 7
Quatech, Inc. Airborne Enterprise Module Databook
2.0 Product Description
The WLNG-AN-DP500 family is the latest generation of 802.11 wireless device servers
from Quatech. The radio features the following:
802.11b/g WiFi Radio with 32bit ARM9 CPU (128Mb SDRAM, 64Mb Flash)
Supports WEP, WPA, WPA2 and 802.1x Supplicant, with Certificates.
The wireless device server includes integrated:
802.11b/g radio driver
TCP/IP stack, UDP, telnet, FTP server
Data bridging and buffering
Command Line Interface
Web interface
WPA Supplicant
802.11 Radio Driver
Supports antenna diversity
Operating Temperature (-40°C to 85°C)
Storage temp (-50°C to 125°C)
36 pin high density SMT connector (Hirose DF12-36)
Dual (2) Hirose U.FL RF connector for RF antenna
Multiple host interfaces supported:
Dual UART (960K BAUD)
Serial (RS232/422/485)
SPI
10/100 Ethernet PHY
Advanced Low power modes
Rugged mounting options.
No host driver required
Small form factor module (Dimensions: 29mm x 21mm x 6.0mm)
Worldwide Regulatory Support
Figure 1- WLNG-AN-DP500 Module Example
8 8/11/2009 100-8080-110
Airborne Enterprise Module DatabookQuatech, Inc.
3.0 Block Diagram
The following outlines the block diagram of the radio:
802.11b/g, UART Interface with
RS232/422/485 Driver Control
llllllllll
WLNG-SP-DP501
802.11b/g, SPI Interface
llllllll
WLNG-AN-DP501
802.11b/g, UART Interface
llllllllll
WLNG-ET-DP501
802.11b/g, 10/100 Ethernet Interface
llllllll
WLNG-EK-DP501802.11b/g Enterprise Class Serial Device Server Module Eval Kit (inc. WLNG-SE/AN-DP501)
l
WLNG-EK-DP502
802.11b/g Enterprise Class SPI Device Server Module Eval Kit (inc. WLNG-SP-DP501)
l
WLNG-EK-DP503802.11b/g Enterprise Class Ethernet Bridge Module Eval Kit (inc. WLNG-ET-DP501)
l
RoHS
Eval Kit
Model Number
Interface
Security
Description
4.0 Model Numbers
The following table identifies the model numbers associated with the device server family.
Please contact Quatech sales for details, quotes and availability.
Table 1 - Model Numbers
10 8/11/2009 100-8080-110
Airborne Enterprise Module DatabookQuatech, Inc.
Pin
Name
Device
Type
Description
1
GND
All
Digital Ground
2
TDI
All
JTAG: Test data in
3
VDD
All
3.3VDC
4
VDD
All
3.3VDC 5 RTCK
All
JTAG: Return Test Clock
6
DTXD
All
D
OUT
Debug
7
/RESET
All
Module RESET 8 DRXD
All
DIN Debug
9
RXD2
UART
DIN UART2
RXD2
Serial
DIN UART2
RXD2
SPI
DIN UART2
RXD2
Ethernet
DIN UART2
G6
All
GPIO
10
TDO
All
JTAG: Test data out
11
/FRESET
All
Factory RESET
12
CTS1
UART
Clear-to-Send UART1
CTS
Serial
Clear-to-Send
/SPI_SEL
SPI
SPI Select
CTS1
Ethernet
Clear-to-Send UART1
F5
All
GPIO
13
NC
UART
No Connect
NC
Serial
No Connect
NC
SPI
No Connect
RX+
Ethernet
Ethernet RX+
14
NC
UART
No Connect
NC
Serial
No Connect
NC
SPI
No Connect
RX-
Ethernet
Ethernet RX-
15
GND
All
Digital Ground
16
GND
All
Digital Ground
17
RTS2
UART
Ready-to-Send UART2
/TXEN
Serial
Line Driver Tx enable
RTS2
SPI
Ready-to-Send UART2
RTS2
Ethernet
Ready-to-Send UART2
G2
All
GPIO
18
RTS1
UART
Ready-to-Send UART1
RTS
Serial
Ready-to-Send
SPI_CLK
SPI
SPI Clock Input
RTS1
Ethernet
Ready-to-Send UART1
5.0 Pin out and Connectors
Pin definition is dependent upon the device type selected. The specific pin function is
defined in Table 2 for each device type. Where multiple options are available for a single
device type, these options are software selectable by the device firmware.
Table 2 – Module Pin Definition
100-8080-110 8/11/2009 11
Quatech, Inc. Airborne Enterprise Module Databook
Pin
Name
Device
Type
Description
F4
All
GPIO
19
CTS2
UART
Clear-to-Send UART2
RXEN
Serial
Line driver Rx enable
CTS2
SPI
Clear-to-Send UART2
CTS2
Ethernet
Clear-to-Send UART2
G1
All
GPIO
20
TCK
All
JTAG: Test clock
21
TXD2
UART
D
OUT
UART2
TXD2
Serial
D
OUT
UART2
TXD2
SPI
D
OUT
UART2
TXD2
Ethernet
D
OUT
UART2
G7
All
GPIO
22
G0
UART
GPIO
SER_MODE
Serial
Serial interface type selection (RS232/422/485)
SPI_INT
SPI
SPI Interrupt
G0
Ethernet
GPIO
23
LED_CON
All
Valid TCP/IP Connection Indicator
F6
GPIO
24
RXD1
UART
DIN UART1
RXD1
Serial
DIN UART1
MOSI
SPI
DIN SPI
RXD1
Ethernet
DIN UART1
F7
All
GPIO
25
LED_POST
All
POST Status Indicator
F0
GPIO
26
LED_WLN_CFG
All
Module TCP/IP Configuration Indicator
F3
GPIO
27
LED_RF_LINK
All
Module RF Link Status Indicator
F2
GPIO
28
TXD1
UART
D
OUT
UART1
TXD
Serial
D
OUT
MISO
SPI
D
OUT
SPI
TXD1
Ethernet
D
OUT
UART1
F1
All
GPIO
29
NC
UART
No Connect
NC
Serial
No Connect
NC
SPI
No Connect
TX-
Ethernet
Ethernet TX-
30
NC
UART
No Connect
NC
Serial
No Connect
NC
SPI
No Connect
TX+
Ethernet
Ethernet TX+
31
NTRST
All
JTAG: Test RESET signal
32
TMS
All
JTAG: Test mode select
33
VDD
All
3.3VDC
34
VDD
All
3.3VDC
35
LED_RF_ACT
All
Radio Status Indicator, driven by the radio.
36
GND
All
Digital Ground
12 8/11/2009 100-8080-110
Loading...
+ 25 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.