DVTEL INC.
65 Challenger Road
Ridgefield Park, NJ 07660
The contents of this guide may not be
reproduced or reprinted in whole or in
part without the express written
permission of DVTEL, Inc.
Quasar CF-3211/CF-4221
Fixed IP Camera
User and Installation Guide
Rev G June 2014
Table of Contents
Table of Contents
1 Document Information ................................................................................................... vii
2 Overview .........................................................................................................................1
2.1 Features .......................................................................................................................... 1
2.2 Package Contents ........................................................................................................... 2
2.3 Typical CF-3211/CF-4221 Camera .................................................................................. 2
3 Introduction to the CF-3211 and CF-4221 Fixed IP Cameras ...............................................3
3.1 CF-3211/CF-4221 Camera Dimensions ........................................................................... 3
3.2 Camera Connections ....................................................................................................... 3
4 System Requirements ......................................................................................................5
5 Installation ......................................................................................................................7
5.1 Indoor Installation .......................................................................................................... 7
5.2 Power and Ethernet Cable Connection .......................................................................... 7
5.3 Lens Mounting ................................................................................................................ 8
5.4 Initial Camera Configuration .......................................................................................... 9
5.5 Mounting Instructions .................................................................................................. 10
6 Using the DNA Utility to Search and Access the Camera .................................................. 13
6.1 Introduction .................................................................................................................. 13
6.2 Quick Start .................................................................................................................... 13
6.3 Main Screen .................................................................................................................. 14
6.4 Navigation Bar .............................................................................................................. 14
6.5 Context Menu ............................................................................................................... 15
6.6 Configuring Communication Settings on the Quasar Camera ...................................... 15
6.7 Adjusting and Framing-Up the Camera View ............................................................... 19
7 Configuration and Operation .......................................................................................... 21
7.1 Browser-Based Viewer Introduction ............................................................................ 21
7.2 Home Page .................................................................................................................... 23
7.2.1 CF-3211/CF-4221 Camera Home Page ..................................................................... 23
7.3 System-Related Settings ............................................................................................... 24
7.3.1 System ...................................................................................................................... 25
7.3.2 Security ..................................................................................................................... 26
7.3.3 Network .................................................................................................................... 33
7.3.4 DDNS ........................................................................................................................ 39
7.3.5 Mail ........................................................................................................................... 40
7.3.6 FTP ............................................................................................................................ 41
7.3.7 HTTP ......................................................................................................................... 42
7.3.8 Application ............................................................................................................... 43
i
Quasar CF-3211/CF-4221 User and Installation Guide
7.3.9 Motion Detection ..................................................................................................... 47
7.3.10 Network Failure Detection ....................................................................................... 51
7.3.11 Tampering Alarm ...................................................................................................... 52
7.3.12 Storage Management ............................................................................................... 54
7.3.13 Recording ................................................................................................................. 56
7.3.14 Schedule ................................................................................................................... 57
7.3.15 File Location ............................................................................................................. 58
7.3.16 View Information ..................................................................................................... 59
7.3.17 Factory Default ......................................................................................................... 62
7.3.18 Software Version ...................................................................................................... 63
7.3.19 Software Upgrade .................................................................................................... 64
7.3.20 Maintenance ............................................................................................................ 66
7.4 Video and Audio Streaming Settings ............................................................................ 67
7.4.1 Video Format ............................................................................................................ 67
7.4.2 Video Compression .................................................................................................. 78
7.4.3 Video OCX Protocol .................................................................................................. 79
7.4.4 Video Frame Rate ..................................................................................................... 80
7.4.5 Video Mask ............................................................................................................... 81
7.4.6 Audio ........................................................................................................................ 82
7.5 Camera-Related Settings .............................................................................................. 83
7.5.1 Exposure ................................................................................................................... 84
7.5.2 White Balance .......................................................................................................... 87
7.5.3 Picture Adjustment .................................................................................................. 88
7.5.4 Backlight ................................................................................................................... 89
7.5.5 Digital Zoom ............................................................................................................. 90
7.5.6 IR Function ............................................................................................................... 90
7.5.7 WDR Function .......................................................................................................... 91
7.5.8 Noise Reduction ....................................................................................................... 92
7.5.9 TV System ................................................................................................................. 92
7.6 Logout ........................................................................................................................... 93
Appendices .......................................................................................................................... 94
A.1. Technical Specifications ................................................................................................ 95
A.2. Device Search Software ................................................................................................ 98
A.2.1 Initial Camera Configuration .................................................................................... 98
A.2.2 Searching and Accessing the Camera with Device Search ..................................... 100
A.2.3 Configuring Communication Settings of a Quasar Camera .................................... 101
ii
Table of Contents
A.3. Internet Security Settings ........................................................................................... 104
A.4. Install UPnP Components ........................................................................................... 106
A.5. Deleting the Existing DCViewer .................................................................................. 108
A.6. Deleting Temporary Internet Files .............................................................................. 109
A.7. Back Focus Adjustment .............................................................................................. 110
A.8. Connecting Wires to a Spring Clamp Terminal Block ................................................. 112
A.9. Mounting and Lens Accessories ................................................................................. 113
Contacting DVTEL ............................................................................................................... 114
iii
Quasar CF-3211/CF-4221 User and Installation Guide
List of Figures
Figure 1: Package Contents....................................................................................................................... 2
Figure 2: CF-3211/CF-4221 Camera – Front View .................................................................................... 2
Figure 3: CF-3211/CF-4221 Camera Dimensions ..................................................................................... 3
Figure 4: CF-3211/CF-4221 Camera Input/Output Connections ............................................................... 3
Figure 5: Auto Iris Port Connection ............................................................................................................ 9
Figure 6: Discovered IP Devices ................................................................................................................ 9
Figure 7: Assign IP Dialog Box ................................................................................................................ 10
Figure 8: Cable Gland .............................................................................................................................. 11
Figure 9: DVTEL CF-X201-00 Camera Housing...................................................................................... 12
Figure 10: DNA Main Screen ................................................................................................................... 14
Figure 11: Context Menu .......................................................................................................................... 15
Figure 12: Windows Firewall Screen ....................................................................................................... 16
Figure 13: Discovered IP Devices ............................................................................................................ 16
Figure 14: DNA Assign IP – Use DHCP Dialog Box ................................................................................ 16
Figure 15: DNA Assign IP – Static IP Dialog Box .................................................................................... 17
Figure 16: Installing the ActiveX Control .................................................................................................. 18
Figure 17: Security Window ..................................................................................................................... 18
Figure 18: Camera Lens Zoom and Focus Adjustment ........................................................................... 20
Figure 19: Camera Housing Repositioning .............................................................................................. 20
Figure 20: Quasar Browser-Based User Interface ................................................................................... 21
Figure 21: Home Page Function Buttons ................................................................................................. 23
Figure 22: System Screen ........................................................................................................................ 24
Figure 23: Security Screen Tabs ............................................................................................................. 26
Figure 24: Security Screen....................................................................................................................... 26
Figure 25: Editing Password and Privileges ............................................................................................ 27
Figure 26: Modifying Account Authority ................................................................................................... 28
Figure 27: HTTPS Screen ........................................................................................................................ 28
Figure 28: HTTPS Screen – Create Self-Signed Certificate .................................................................... 29
Figure 29: HTTPS Screen – Install Signed Certificate ............................................................................. 29
Figure 30: Example of Self-Signed Certificate ......................................................................................... 30
Figure 31: Self-Signed Certificate – Details ............................................................................................. 30
Figure 32: IP Filter Screen ....................................................................................................................... 31
Figure 33: IEEE 802.1X/EAP-TLS Screen ............................................................................................... 32
Figure 34: Network Screen ...................................................................................................................... 33
Figure 35: QoS Screen ............................................................................................................................ 35
Figure 36: SNMP Settings Screen ........................................................................................................... 36
Figure 37: UPnP Screen .......................................................................................................................... 37
Figure 38: Direct Access to Camera with UPnP Enabled ........................................................................ 38
Figure 39: DDNS Screen ......................................................................................................................... 39
Figure 40: Mail Screen – SMTP ............................................................................................................... 40
Figure 41: FTP Screen ............................................................................................................................. 41
Figure 42: HTTP Screen .......................................................................................................................... 42
Figure 43: Application Screen .................................................................................................................. 43
Figure 44: Application – Record Stream to SD Card ............................................................................... 44
Figure 45: Application – Upload Image by FTP ....................................................................................... 45
Figure 46: Application – Upload Image by E-Mail .................................................................................... 45
Figure 47: Application – Send HTTP Notification .................................................................................... 46
Figure 48: Motion Detection Screen ........................................................................................................ 47
Figure 49: Motion Detection Screen – with Schedule Drop-Down Menu ................................................ 48
Figure 50: Network Failure Detection Screen .......................................................................................... 51
Figure 51: Tampering Alarm Screen ........................................................................................................ 52
Figure 52: Storage Management Screen ................................................................................................. 54
Figure 53: Video File Recording List ........................................................................................................ 55
Figure 54: Selected File Window ............................................................................................................. 56
Figure 55: Recording Screen ................................................................................................................... 56
Figure 56: Schedule Screen..................................................................................................................... 57
Figure 57: File Location Screen ............................................................................................................... 58
Figure 58: System Log Screen ................................................................................................................ 59
Figure 59: User Information Screen ......................................................................................................... 60
iv
Table of Contents
Figure 60: User Information – Privileges Screen ..................................................................................... 61
Figure 61: Parameter List Screen ............................................................................................................ 62
Figure 62: Factory Default Screen ........................................................................................................... 62
Figure 63: Partial Restore Screen ............................................................................................................ 63
Figure 64: Software Version Screen ........................................................................................................ 63
Figure 65: Software Upgrade Screen ...................................................................................................... 64
Figure 66: Software Upgrade – In Process .............................................................................................. 65
Figure 67: Maintenance Screen ............................................................................................................... 66
Figure 68: File Download Screen ............................................................................................................. 66
Figure 69: Video Format Screen .............................................................................................................. 67
Figure 70: Video Rotate Type Screen ...................................................................................................... 76
Figure 71: View-1 (Source) ...................................................................................................................... 77
Figure 72: View-2 Image Rotated Vertically (Reversed) .......................................................................... 77
Figure 73: Video Compression Screen .................................................................................................... 78
Figure 74: Video OCX Protocol Screen ................................................................................................... 79
Figure 75: Video Frame Rate Screen ...................................................................................................... 80
Figure 76: Mask Screen ........................................................................................................................... 81
Figure 77: Audio Screen .......................................................................................................................... 82
Figure 78: Camera Settings Screen ......................................................................................................... 83
Figure 79: Camera Settings Screen – Exposure ..................................................................................... 84
Figure 80: Camera Settings Screen – White Balance ............................................................................. 87
Figure 81: Camera Settings Screen – Picture Adjustment ...................................................................... 88
Figure 82: Camera Settings Screen – Backlight ...................................................................................... 89
Figure 83: Camera Settings Screen – Digital Zoom ................................................................................ 90
Figure 84: Camera Settings Screen – IR Function .................................................................................. 91
Figure 85: Camera Settings Screen – WDR Function ............................................................................. 91
Figure 86: Camera Settings Screen – Noise Reduction .......................................................................... 92
Figure 87: Camera Settings Screen – TV System ................................................................................... 92
Figure 88: Login Message........................................................................................................................ 93
Figure 89: Login Window ......................................................................................................................... 93
Figure 90: Device Search Application ...................................................................................................... 98
Figure 91: Windows Security Alert ......................................................................................................... 101
Figure 92: Device Search Application – Select Browse ......................................................................... 102
Figure 93: Device Search Application – Select Install ActiveX Control ................................................. 102
Figure 94: Security Warning Window ..................................................................................................... 103
Figure 95: Command Bar Toolbar – Select Internet Options ................................................................. 104
Figure 96: Internet Options Screen ........................................................................................................ 104
Figure 97: Command Bar Toolbar – Internet Options ............................................................................ 105
Figure 98: Schedule Screen................................................................................................................... 105
Figure 99: Back Focus Adjustment ........................................................................................................ 110
Figure 100: Typical Spring Clamp Terminal Block ................................................................................. 112
Figure 101: Connecting a Wire to a Terminal Block .............................................................................. 112
v
Revision History
Version
Date
Author
Comments
A
Oct. 2013
Jonathan Herman
Merged CF-3211 and CF-4221 User and
Installation Guides. Updated look and feel.
B-E
Nov.-Dec. 2013
Alan Singer
General editing and formatting.
F
Mar. 2014
Alan Singer
Added Revision History. Updated DNA
screenshots in section 6. Updated look and
feel.
G
Jun. 19, 2014
Alan Singer
Corrected image sensor and sensitivity
specifications.
Revision History
vi
Document Information
Note:
This document is intended for use by technical users who have a basic understanding of
CCTV camera/video equipment and LAN/WAN network connections.
Warning:
Installation must follow safety, standards, and electrical codes as well as the laws that
apply where the units are being installed.
1 Document Information
Document Scope and Purpose
The purpose of this document is to provide instructions and installation procedures for physically
connecting the Quasar CF-3211 and CF-4221 cameras. After completing the physical installation,
additional setup and configurations may be required before video analysis and detection can
commence.
Proprietary Rights and Non-Disclosure
This manual is delivered subject to the following restrictions and conditions:
This document contains proprietary information belonging to DVTEL, Inc. This information
is supplied solely for the purpose of assisting explicitly the licensee of the DVTEL units.
No part of this document contents may be used for any other purpose, disclosed to any
third party or reproduced by any means, electronic or mechanical, without the express
prior written permission of DVTEL, Inc.
Trademarks and Copyrights
This manual and its contents herein are owned by DVTEL, Inc. All rights reserved.
DVTEL, the DVTEL logo, Quasar CF-3211 and CF-4221 are trademarks of DVTEL, Inc.
Products and trademarks mentioned herein are for identification purposes only and may be
registered trademarks of their respective companies.
DVTEL, Inc. makes no representations whatsoever about any other products or trademarks
mentioned in the manual.
© DVTEL, Inc. 2014. All rights reserved.
vii
Quasar CF-3211/CF-4221 User and Installation Guide
A Warning is a precautionary message that indicates a procedure or condition where
there are potential hazards of personal injury or death.
A Caution is a precautionary message that indicates a procedure or condition where
there are potential hazards of permanent damage to the equipment and or loss of data.
A Note is useful information to prevent problems, help with successful installation, or to
provide additional understanding of the products and installation.
A Tip is information and best practices that are useful or provide some benefit for
installation and use of DVTEL products.
Disclaimer
Users of DVTEL products accept full responsibility for ensuring the suitability and considering the
role of the product detection capabilities and their limitation as they apply to their unique site
requirements.
DVTEL, Inc. and its agents make no guarantees or warranties to the suitability for the users’ intended
use. DVTEL, Inc. accepts no responsibility for improper use or incomplete security and safety
measures.
Failure in part or in whole of the installer, owner, or user in any way to follow the prescribed
procedures or to heed WARNINGS and CAUTIONS shall absolve DVTEL, Inc. and its agents from any
resulting liability.
Specifications and information in this guide are subject to change without notice.
Document Conventions
WARNING and CAUTION notes are distributed throughout this document, whenever applicable, to
alert you of potentially hazardous situations. These may be hazards associated with a task or a
procedure you are carrying out or are about to carry out.
The following document conventions are used throughout this manual:
General Cautions and Warnings
This section contains information that indicates a procedure or condition where there are potential
hazards. These may be hazards associated with a task or procedure a user is carrying out or about to
carry out. WARNINGS and CAUTIONS are distributed throughout this document, whenever
applicable, to alert the user of potentially hazardous situations.
SAVE ALL SAFETY AND OPERATING INSTRUCTIONS FOR FUTURE USE.
Although the unit is designed and manufactured in compliance with all applicable safety standards,
certain hazards are present during the installation of this equipment.
To help ensure safety and to help reduce risk of injury or damage, observe the following:
viii
Warning:
1. The camera cover is an essential part of the product. Do not open or remove it.
2. Never operate the camera without the cover in place. Operating the camera
without the cover poses a risk of fire and shock hazards.
3. Do not disassemble the camera or remove screws. There are no user
serviceable parts inside the unit.
4. Only qualified trained personnel should service and repair this equipment.
5. Observe local codes and laws and ensure that installation and operation are in
accordance with fire, security and safety standards.
Electrical Safety Notice and Warnings
Warning:
1. Read the installation instructions before you connect the unit to a power source.
2. Electrical safety should always be observed. All electrical connections must be
performed by a certified electrician.
3. Use the supplied power supply and protect against static electricity,
ground faults and power surges.
4. The unit uses a three-wire power cord to make sure that the product is properly
grounded when in use. If the intended power outlet does not support three
prongs, one of which is a ground, contact an electrician to install the appropriate
outlet. NEVER remove or otherwise attempt to bypass the ground pin of the
power cord. Do not operate the unit in the absence of a suitably installed ground
conductor.
5. If you use an extension cord with this system, make sure that the total ampere
rating on the products plugged into the extension cord does not exceed the
extension cord ampere rating.
6. To avoid possible shock hazards or damaging the unit, assure that the positive
and negative of the power leads are properly connected to the terminal block
connector before plugging it into the unit or turning on the power source.
7. In the following situations, the electric power should be turned off immediately
and appropriate repairs, replacements or remedies should be taken if:
The power line or plug is damaged, frayed or shows heavy wear.
The unit has been physically crushed or deformed.
The unit has been exposed to water.
The unit has been exposed to, or shows signs of damage from, fire,
intense heat, heavy smoke, fumes, or vapors.
Electrical connections of the unit become abnormally hot or generate
smoke.
The unit has been dropped, damaged or shows signs of loose internal
parts.
The unit does not operate properly.
Document Information
ix
Quasar CF-3211/CF-4221 User and Installation Guide
Caution:
To avoid damage from overheating or unit failure, assure that there is sufficient
temperature regulation to support the unit’s requirements (cooling/heating). Operating
temperature should be kept in the range 0° to 50°C (32° to 122°F), with no more than
90% relative humidity (non-condensing).
Minimizing EMI and RFI
When wires run for a significant distance in an electromagnetic field, electromagnetic interference
(EMI) can occur. Strong EMI (e.g. lightning or radio transmitters) can destroy the units and can pose
an electrical hazard by conducting power through lines and into the system. Poor quality or worn
wiring can result in radio frequency interference (RFI). To minimize the effects of EMI and RFI,
consult your reseller.
Site Preparation
There are several requirements that should be properly addressed prior to installation at the site.
The following specifications are requirements for proper installation and operation of the unit:
Ambient Environment Conditions: Avoid positioning the unit near heaters or heating
system outputs. Avoid exposure to direct sunlight. Use proper maintenance to ensure that
the unit is free from dust, dirt, smoke, particles, chemicals, water or water condensation,
and exposure to EMI.
Accessibility: The location used should allow easy access to unit connections and cables.
Safety: Cables and electrical cords should be routed in a manner that prevents safety
hazards, such as from tripping, wire fraying, overheating, etc. Ensure that nothing rests on
the unit’s cables or power cords.
Ample Air Circulation: Leave enough space around the unit to allow free air circulation.
Cabling Considerations: Units should be placed in locations that are optimal for
the type of video cabling used between the unit and the cameras and external
devices. Using a cable longer than the manufacturer’s specifications for optimal
video signal may result in degradation of color and video parameters.
Physical Security: The unit provides threat detection for physical security systems. In order
to ensure that the unit cannot be disabled or tampered with, the system should be installed
with security measures regarding physical access by trusted and un-trusted parties.
Network Security: The unit transmits over IP to security personnel for video surveillance.
Proper network security measures should be in place to assure networks remain operating
and free from malicious interference. The unit is intended for installation on the backbone
of a trusted network.
Electrostatic Safeguards: The unit as well as other equipment connected to it (relay
outputs, alarm inputs, racks, carpeting, etc.) shall be properly grounded to prevent
electrostatic discharge.
The physical installation of the unit is the first phase of making the unit operational in a security
plan. The goal is to physically place the unit, connect it to other devices in the system, and to
establish network connectivity.
x
Overview
Caution:
If you are using DVTel Latitude, we recommend that you configure the camera’s settings
via the AdminCenter. This is because the camera’s web-based interface might be
overwritten by Latitude settings. Refer to the Latitude online help for information
regarding configuring camera settings.
Progressive scan CMOS
sensor
H.264 and MJPEG
compression
Motion selection with Region Of
Interest masking
Privacy masks
WDR and ATW
3DNR image noise reduction
Day/Night (IR Cut Filter)
Micro SD recording
support
BNC analog output
ONVIF support
Analog video output
Supports PoE/12VDC/24VAC
Edge motion detection
Multiple users
RTSP support
Security IP restricted
access allow/deny list
Built-in web application/
web server
Group permissions
HTTP streaming MPEG
SNMP v1/v2/v3 SNMP
Traps
Per-user permissions
E-mail SMTP alarm
notification (up to 2
emails)
FTP upload (up to 2
locations)
Dual HTTP notification server
support (up to 2 servers)
Detection event-driven
alarms
Alarm input driven events
Relay output actions on alarm
Send images on alarm to
e-mail
Upload alarm images to
FTP
Record snapshots to SD card on
alarm
Sequential snapshot
numbering
UPnP support
Historical motion detection levels
detected and recorded at frame
levels.
Tampering detection and
notification
Two encoder streams
available
Low lux
Note:
MJPEG is not supported by Latitude.
2 Overview
The Quasar CF-3211 and CF-4221 series fixed cameras are HD 720p and Full HD 1080p devices,
respectively. These cameras provide real-time, H.264 multi-streaming video and the highest quality
image. With its compact, sophisticated and aesthetic mechanical design, the lightweight DVTEL
CF-3211 and CF-4221 cameras are simple and easy to install.
2.1 Features
Following are key features of the CF-3211/CF-4221 camera:
1
Quasar CF-3211/CF-4221 User and Installation Guide
Full HD Multiple Streaming
Camera
Back focus adjuster
Quick-start guide
CD
(Bundled software and
documentation)
Item
Designation
Description
1
Lens
Camera lens
2
Focus fixing knob
To set the focus, loosen and tighten by hand the adjustment
knob until the optimum focus is obtained.
3
Zoom fixing knob
To set the zoom, loosen and tighten by hand the adjustment
knob until the optimum zoom is obtained.
2.2 Package Contents
Before proceeding, please check that the box contains the items listed here. If any item is missing or
has defects, do not install or operate the product and contact your dealer for assistance.
Figure 1: Package Contents
2.3 Typical CF-3211/CF-4221 Camera
The figure below shows a typical CF-3211/CF-4221 series camera.
Figure 2: CF-3211/CF-4221 Camera – Front View
Table 1: CF-3211 Camera Adjustment Locations
2
Introduction to the CF-3211 and CF-4221 Fixed IP Cameras
3 Introduction to the CF-3211 and CF-4221 Fixed IP Cameras
This chapter provides the camera dimensions for reference before installation. Each connector
located inside the camera’s housing is also identified. See Figure 4 and Table 2.
Related Links
CF-3211/CF-4221 Camera Dimensions
Camera Connectors
Appendix A.1: Technical Specifications
3.1 CF-3211/CF-4221 Camera Dimensions
The mechanical dimensions of a CF-3211/CF-4221 Fixed IP Camera are shown below.
Figure 3: CF-3211/CF-4221 Camera Dimensions
3.2 Camera Connections
Figure 4 shows the various connectors and reset button contained within the housing of the CF-3211
and CF-4221 cameras. The connectors, pin numbers and signal definitions related to each pin are
listed in Table 1.
Figure 4: CF-3211/CF-4221 Camera Input/Output Connections
3
Quasar CF-3211/CF-4221 User and Installation Guide
ID
Connector Name
Pin No./ Connector Type
Definition
Description
1
Line Out
Audio out
2-way audio
transmission
2
Line In/Mic In
Audio in
3
PoE Network
RJ45, Network LEDs
10/100 Mbps
Ethernet/PoE
Power over Ethernet
4
Video
BNC
Analog video
For video output
5
SD
microSD card slot
For video and snapshots
storage (card not
included)
6
DC 12V/AC 24V
1 – Power (+)
2 – Reserved
3 – GND (-)
12V DC
Power supply
connection indication
(green LED)
1- Power (+)
2- Earth GND
3- Power (-)
24V AC
7
to
9
I/O 1 to 7
1 - Output (+)
2 - Output (-)
Alarm output
7-terminal connection
block
3 - Input (+)
4 - Input (-)
Alarm input
5 - GND
Grounding
6 - D (-)
7 - D (+)
Reserved
Do NOT connect
10
Auto Iris
DC iris lens connector
DC iris port
11
PWR
N/A
Power LED
Power indication
12
RESET
N/A
Reset
Restores factory default
settings
Table 2: CF-3211/CF-4221 Camera Connector Panel Description
4
System Requirements
Item
Minimum System Requirement
Personal Computer
Intel® Pentium®M, 2.16 GHz or Intel® CoreTM2 Duo, 2.0 GHz
2GB RAM or more
Operating System
Windows, Windows XP, Windows 7
Web Browser
Microsoft Internet Explorer 7, 8, or 9
Network Card
10Base-T (10 Mbps) or 100Base-TX (100 Mbps) operation
Viewer
ActiveX control plug-in for Microsoft IE
4 System Requirements
To access the CF-3211/CF-4221 fixed IP camera via a web browser, ensure that your PC has the
proper network connection and meets the system requirements described below.
Table 3: System Requirements
5
Quasar CF-3211/CF-4221 User and Installation Guide
6
Installation
Power and Ethernet
Cable Connection
Initial Camera Configuration
Mounting Instructions
Adjusting and Framing-
Up the Camera View
Note:
An Ethernet crossover cable can be used when connecting the CF-3211/CF-4221
camera directly to the PC.
RJ45
Connector
LED
Description
Green
Link Light - indicates a stable network connection
Yellow
Activity Light - flashes to indicate network activity
5 Installation
Follow the instructions below for indoor installation of the Quasar CF-3211/CF-4221 series camera.
5.1 Indoor Installation
Read the instructions provided in this chapter thoroughly before installing the CF-3211/CF-4221
camera. The following points are additional considerations for indoor installation:
There must be a fuse or circuit breaker at the starting point of the electrical wiring
infrastructure.
For indoor installations, such as industrial applications, the CF-3211/CF-4221 camera must
be protected from hostile external elements (e.g. corrosive environment, metallic dust,
extreme temperatures, soot, moisture, over spray, etc.)
Do not place the CF-3211/CF-4221 camera on or near radiators and heat sources.
All electrical work must be performed in accordance with local regulatory requirements.
Related Links
5.2 Power and Ethernet Cable Connection
Power Connection
Make sure the camera’s power cable is properly connected. Refer to Table 1: CF-3211/CF-4221
Camera Connector Designations. If using Power over Ethernet (PoE), make sure Power Sourcing
Equipment (PSE) is available on the connected network. All electrical work must be performed in
accordance with local regulatory requirements.
Ethernet Cable Connection
A Cat 5 Ethernet cable is recommended for network connection. For best transmission quality, the
cable length should not exceed 100 meters (328 feet). Connect one end of the Ethernet cable to the
CF-3211/CF-4221 camera and the other end of the cable to the network switch or PC.
Check the status of the link indicator and activity indicator LEDs. If the LEDs are unlit, check the LAN
connection.
Table 4: Network Port LED Indications
7
Quasar CF-3211/CF-4221 User and Installation Guide
Note:
The camera lens is sold separately and should be selected to match the needs of the
scene and to optimize the use of the camera capabilities. See Mounting and Lens
Accessories.
Note:
A smaller focal length number allows a wider field of view. A larger focal number
represents a narrower and deeper field of view.
Tip:
Do not touch the sensor or allow dust to accumulate in the lens-mount.
C to CS Mount Adapter
Completion
5.3 Lens Mounting
Before installing your camera, install the camera lens.
Auto Iris vs. DC lens
A manual iris lens is best for use in scenes where illumination never changes, such as a persistently
lit store or office. Auto iris is better suited for scenes where the lighting may vary throughout the
day and night.
The trade-off is in the amount of detail and depth of view vs. the width of view. For example a 2.8 or
4 mm lens might be sufficient for indoor warehouse and office and an 8mm might be better suited
for outdoor perimeters.
After you select your lenses and see the amount of detail provided consider your security
surveillance coverage, camera locations and any additional needs that may be discovered. Consult
your DVTEL rep if you have any questions.
To mount a lens on the CF-3211/CF-4221 camera
1. Remove the plastic insert covering the threaded camera lens-mount.
2. If you are using a C-mount lens, screw a 5mm adapter ring into the C-Mount to
convert it to a CS-Mount (see Figures below).
3. Align the lens threads into the lens-mount and screw on the lens.
8
4. If your lens has a DC auto iris, plug the auto-iris cable from the motorized lens
Tip:
If there are problems focusing, it might be necessary to make a back focus adjustment.
Note:
DNA is an enhanced software alternative to Device Search. Either of these
programs may be used. They are supplied on the included CD.
assembly into the AUTO IRIS port of the camera.
Figure 5: Auto Iris Port Connection
5.4 Initial Camera Configuration
To perform the initial camera configuration:
Installation
1. Unpack the camera and remove the protective cover.
2. Remove the PE cloth sheet and lens cap. Attach the dome cover to the body.
3. Connect one end of the Cat 5 Ethernet cable to the Ethernet port of the camera and the
RJ45 connector at other end to the Power Sourcing Equipment (PSE) device, such as a
switch.
4. Verify that the RJ45 connector LEDs illuminate green (indicating a stable network
connection) and flashing yellow (to indicate network activity).
5. Do one of the following:
Copy and run the dna.exe from the included CD.
From the Latitude Sidebar, run the Unified Configurator by selecting Applications >
Device Configuration Tool and then, on the Unified Configurator screen, click DVTEL
HD Series.
1. Mark the unit requiring IP assignment.
Figure 6: Discovered IP Devices
9
Quasar CF-3211/CF-4221 User and Installation Guide
Note:
The camera can be connected to a PC for bench installation via an Ethernet crosscable.
Note:
The camera default IP Address and the subnet mask IP Address are automatically
supplied by the DHCP server.
Tip:
A camera setup adapter, such as Veracity Pinpoint, can be used to connect a laptop
directly to the camera when using PoE.
Caution:
The CF series indoor camera must be kept in a clean and dry indoor environment or in a
protective camera housing. Operating temperature should be maintained within -10°C
to 50°C (14° to 122°F). Operating humidity is 10% to 90% (non-condensing). The camera
should be kept dry, free from water condensation, dust, dirt, and smoke.
2. Right-click on the mouse and select the assigned IP or press the Assign IP button to open the
DNA Assign IP screen.
3. In the dialog box that is displayed, enter values for the IP Address, Gateway and Netmask.
4. Click Update and wait for OK status to be displayed.
Figure 7: Assign IP Dialog Box
5. Disconnect the Ethernet cable. The camera is ready for deployment (mounting) in a site
installation.
5.5 Mounting Instructions
The following are mounting instructions for the DVTEL CF-3211 and CF-4221 Fixed IP cameras.
10
To mount the camera, follow one of these procedures:
For indoor installations without a housing:
a. On the ceiling/wall/flat surface, install a security camera wall mount bracket stand
that is sturdy enough to hold the camera in a fixed position for the field of view
required.
b. Screw the bracket/stand to the mounting socket on the bottom of the camera.
c. Connect the cables and wiring to the camera. See Figure 4: CF-3211/CF-4221 Camera
Input/Output Connections and Table 2.
For indoor/outdoor installations using a typical protective camera housing:
a. Thread the wires through any of the infrastructure and brackets (e.g. pole
bracket/corner bracket/etc.) as needed as well as through the wall bracket arm.
b. Bolt the wall bracket (arm) to the prepared surface.
c. Loosen the screws or unlatch the camera housing lid, open the housing and loosen
the plastic cable glands (cable fittings).
d. Thread the cables through the cable glands into the camera housing.
Installation
Figure 8: Cable Gland
e. Attach the camera housing to the wall bracket (arm) using the provided screws and
wrench.
f. Remove the housing plate (base for camera) and using the provided camera mount
screw, thread the screw through the plate into the camera’s bottom mounting
socket.
g. Put the camera mounted on the base plate back in the housing. (We will adjust
forward positioning when we adjust the lens.)
h. For housings with internal blowers and heaters, connect the wiring to the camera
housing terminals (power input) according to the manufacturer’s instructions for
heaters (heater output) and fans (blower output) that the camera housing features.
Connect any ground (GND) to the camera housing ground connection.
i. Connect the cables and wiring to the camera. See Figure 4: CF-3211/CF-4221
Camera Input/Output Connections and Table 2.
11
Quasar CF-3211/CF-4221 User and Installation Guide
Note:
For outdoor installation, the camera must be installed in a protective
housing such as a DVTEL CF-X201-00 camera housing. See Figure 9.
Figure 9: DVTEL CF-X201-00 Camera Housing
12
Using the DNA Utility to Search and Access the Camera
Note:
DNA is an enhanced software alternative to Device Search. Either of these programs may
be used.
Caution:
Users who have previously installed the DVTEL Web Player (DCViewer) on the PC should
delete the existing DCViewer from the PC before accessing the camera. For information
on how to uninstall and clear Temporary Internet Files, see Appendix A5: Deleting the
Existing DCViewer.
6 Using the DNA Utility to Search and Access the Camera
6.1 Introduction
The DVTEL Network Assistant (DNA) is a user-friendly utility that is designed to easily discover and
configure DVTEL edge devices on a network.
The DNA tool has a simple user interface and does not require any installation. The software is
provided as a single, standalone executable. It runs on any PC.
DNA provides a central location for listing all the DVTEL CM, CF and CP camera models accessible
over the network. Once listed, each camera can be right-clicked to access and change the network
settings.
If the network settings are changed for some reason, a new search will relist the units. The units may
then be configured via the web interface.
If DVTEL Latitude is being used, configure the unit with a static IP address rather than with DHCP.
This ensures that the IP address will not automatically change in the future and interfere with
configurations and communication.
The camera must be made accessible for the network’s addressing.
To install DVTEL Web Player (DCViewer) software online:
Upon initial connection to the camera, a prompt to install the DVTEL Web Player (DCViewer)
appears. If the web browser does not allow DVTEL Web Player to install, check the Internet security
settings or ActiveX controls and plug-in settings to continue the process. See Internet Security
Settings.
Follow the instructions below to start using the DNA application.
6.2 Quick Start
1. Install and run the DNA application on a computer connected to the network. The
software is an .exe file supplied in a zip file together with an Online Help file (.chm).
2. Extract both files from the zip file, and place them together in a new directory. Both files
should have the same name, but different extensions (.exe and .chm).
3. Upon launching the tool, DNA automatically discovers all devices on the network. The
initial launch creates a default .ini file (dna.ini).
4. In the event that there are devices that are not authenticated, click Login and enter login
credentials for the devices.
13
Quasar CF-3211/CF-4221 User and Installation Guide
5. If there are devices located on a separate VLAN, the devices must be added manually.
Click Add Device Manually from the Operational Toolbar and add the devices.
6.3 Main Screen
The DNA main screen contains four sections, as seen in the following figure:
Figure 10: DNA Main Screen
6.4 Navigation Bar
The callouts on the screen are explained below:
1. Navigation Bar: Located at the top of the screen. Includes tabs and dropdown menus to
perform actions.
2. Operational Toolbar: Located below the Navigation Bar. Used to refresh discovered
units, filter connected devices for easy operation, and to add a device manually.
3. Discover List: Occupies the center of the screen. Displays a list of discovered devices
with partial device information.
4. Status Bar: Located at the bottom of the screen. Displays current device status, including
scanning time, status, and the number of discovered units.
The Navigation Bar contains tabs for all the actions needed to configure and manage attached
devices. If no devices have been discovered, all the tabs are gray (disabled).
After a device has been discovered, the tabs for functions which it supports are enabled and colored,
as seen in the following Figure:
14
Using the DNA Utility to Search and Access the Camera
Note:
DNA is an alternative software to Device Search. Either of these programs may
be used.
To define the device on which to perform an action, the user must select the device from the
Discover List. The user can select more than one device, in which case the action will be done on all
selected devices.
6.5 Context Menu
All functions on the Navigation Bar are also accessible from the context menu, which is available
when right-clicking on a device within the Discover List, as seen in the following figure:
Figure 11: Context Menu
Assign IP Tab
The Assign IP tab or context menu option is used to automatically assign the IP address of the
selected device(s). This function can be used for automatic batch network configuration.
The Assign IP tab or context menu option is used to automatically assign the IP address of the
selected device(s). This function can be used for automatic batch network configuration. The Assign
IP tab or context menu option is grayed if a device has not been selected.
Selecting this tab or option opens the Assign IP window, which displays a list of devices which need
to be updated, as shown in the illustration below. The Assign IP window is divided into two areas
See section 6.6 for more details.
6.6 Configuring Communication Settings on the Quasar Camera
To configure communication settings on the camera:
1. Connect the camera to the network on the same VLAN/LAN as the workstation.
2. If the network supports the default, open DNA utility by running dna.exe which can be
found in the DNA Utility folder in the supplied CD, , or click the DNA icon .
3. In the DNA application, click the DNA button.
4. If the Windows Firewall is enabled, a security alert window pops up.
15
Quasar CF-3211/CF-4221 User and Installation Guide
5. To continue, click Allow Access. Latitude users should consult the Latitude Installation
Instructions on disabling the Windows Firewall.
Figure 12: Windows Firewall Screen
6. Click Assign IP. All the discovered IP devices will be listed in the page, as shown in the figure
below. The camera’s default IP Address is automatically supplied by the DHCP server.
Figure 13: Discovered IP Devices
7. Right-click the camera whose network property is to be changed. From the menu that
opens, select Network Setup. The Network Setup dialog is displayed.
Figure 14: DNA Assign IP – Use DHCP Dialog Box
16
Using the DNA Utility to Search and Access the Camera
Tip:
Record the camera’s MAC address for future reference.
Note:
ID and password are case-sensitive.
Note:
It is strongly advised that administrator’s password be altered for
security reasons.
8. To access DNA, do one of the following:
a) For DHCP (not supported by Latitude):
i. Select Use DHCP. Do not use for Latitude.
ii. Click Update and wait for status.
b) For Static IP (recommended for Latitude users):
Figure 15: DNA Assign IP – Static IP Dialog Box
i. Do not select the Use DHCP checkbox. This is recommended for security
purposes and for and Latitude users. In the IP Address, Gateway, and Netmask,
enter the respective LAN/VLAN (optional DNS) values.
ii. Click Update and wait for OK status to be displayed.
9. Right-click and select Browse to directly access the camera via a web browser. The default
web browser opens and requests access to the camera IP address.
10. When the web browser contacts the camera IP, do the following:
a) Login using the default user name Admin and password 1234.
17
Quasar CF-3211/CF-4221 User and Installation Guide
Note:
If the password is changed and DVTEL Latitude AdminCenter Discovery feature is
in use, deselect all other proprietary types. Select DVTEL HD Series so that the
new password can be configured in the Discovery tab settings.
b) If the Information Bar (just below the URL bar) prompts for permission to install
the ActiveX Control for displaying video in the browser (see the figure below), rightclick on the Information Bar. Select Install ActiveX Control to allow the installation.
Figure 16: Installing the ActiveX Control
If a security warning window prompt appears, click Install.
Figure 17: Security Window
11. If the wizard appears for installing the component application DCViewer, follow the
instructions to complete the installation.
Additionally, users can change the camera’s network property (either DHCP or Static IP) directly in
the device finding list. Refer to the following section for changing the camera’s network property.
18
Using the DNA Utility to Search and Access the Camera
Tip:
To view greater image detail for more accurate high-definition focusing, on
the web interface Home page, click the Full Screen button and use the
full screen view to check the focus.
Note:
Best focusing results can be achieved when the lens iris is fully open (such as
at night in low light). This prevents loss of sharpness if light levels are
reduced at night.
6.7 Adjusting and Framing-Up the Camera View
After the camera is connected to the network and running, it is necessary to frame-up the scene and
adjust the camera settings to optimize the picture for the individual scenes. If Latitude is being used,
consider scheduling different settings for changing ambient conditions throughout the day, week,
month or seasons.
To adjust and frame-up the camera view:
1. In the DNA application, click DNA.
2. In the results, click to select the camera.
3. Right-click to open the shortcut menu, and select Browse, or enter the camera’s IP
address in your Internet browser’s URL address bar.
4. When the Internet browser connects to the camera and prompts for login, do the
following:
a) Log in using the default user name Admin and password 1234. If the password has
previously been changed, use the new password.
b) Allow the ActiveX to download and choose to install the DVTEL Web Player
(DCViewer).
To achieve this during the day, in the web interface, go to the Camera > Exposure screen
and select from the Exposure Setting menu Auto Shutter mode. Save changes and
complete the focusing steps. When finished, restore your exposure settings as needed.
19
Quasar CF-3211/CF-4221 User and Installation Guide
5. Adjust the Pan and Tilt as follows:
a. For indoor installations without a housing
1. Loosen the tension screw on the bracket/stand and move (pan and tilt) the
camera so that the field of view is optimized for your scene and retighten the
tension bolt to hold the camera in place.
2. On the camera, adjust the zoom ring and focus ring on the camera lens for your
scene. If you have a manual iris, also adjust the iris ring on your lens.
Figure 18: Camera Lens Zoom and Focus Adjustment
b. For indoor or outdoor installations using a protective camera housing
1. Support the camera housing and loosen sufficiently the tension bolt on the
bracket Pan/Tilt assembly so that it allows you to reposition the camera housing.
Figure 19: Camera Housing Repositioning
2. Move the housing so that the camera field of view is optimized for your scene
and retighten the tension bolt on the wall bracket Pan/Tilt assembly.
3. On the camera, adjust the zoom ring and focus ring on the lens for your scene. If
you have a manual Iris, also adjust the iris ring on your lens. See Figure 18.
4. Adjust the camera and base plate by moving it either forward or backward so
that the camera lens close enough to the glass that it reduces the possibility of
reflection but does not make contact with the glass.
5. Tighten the base plate securely in place and close the camera housing lid.
6. Close the latch or tighten the screws firmly so that the lid seal is properly
maintained.
20
Configuration and Operation
7 Configuration and Operation
The Quasar camera is provided with a browser-based configuration interface for video playback and
recording. In this chapter, information about main page introduction, system related settings and
camera settings are described in detail.
Additionally, if DVTEL’s Latitude VMS is used, many of the configurations and features of DVTEL’s
VMS provide configuration and automation of the camera.
This section includes the following information:
Browser-Based Viewer Introduction
Home Page
System-Related Settings
Video and Audio Streaming Settings
Camera-Related Settings
Logout
7.1 Browser-Based Viewer Introduction
The figure below shows the Quasar camera’s browser-based user interface.
Figure 20: Quasar Browser-Based User Interface
21
Quasar CF-3211/CF-4221 User and Installation Guide
At the top of the Viewer window is the navigation bar, which contains five main tabs: Home,
System, Streaming, Camera, and Logout.
Home Page
Users can monitor live video of the targeted area, adjust the display size including use
of the digital zoom feature, activate or de-activate the speaker (audio function), take
snapshots of the view area, stop/start video streaming, and record video in a
designated storage place. Further details are discussed in Home Page.
System Settings
The administrator can set host name, system time, root password, network related
settings, etc. Further details are discussed in System-Related Settings.
Streaming Settings
The administrator can modify video resolution and picture rotation and select audio
compression mode on this page. Further details are discussed in Video and Audio
Streaming Settings.
Camera Settings
The administrator can adjust many of the camera settings on this page, such as
Exposure, White Balance, Picture, Backlight, Digital Zoom, IR Function, WDR Function,
Noise Reduction, and TV System. Further details are discussed in Camera-Related
Settings.
Logout
Click on the tab to re-login the camera with another username and password. See
Logout.
The following items are displayed on the screen:
In the top right-hand corner of the Viewer window, the camera model number is displayed.
Below the camera model number is the Language bar. Supported languages include English,
German, French, Italian, Simplified Chinese, Traditional Chinese, Russian, and Korean.
In the center of the Viewer window is the Live View pane, which displays the image that the
camera is monitoring.
On the right side of the black bar at the top of the Live View pane is the Time Display.
Under the Live View pane is the Video Format selection, enabling H.264-1 or H.264-2 to be
selected.
Below the Video Format selection are the Function buttons, which are discussed in the
following section.
Under the Function buttons are the Video Compression details, including bit rate,
compression, and quality.
In the bottom right-hand corner of the Viewer window, the firmware version of the camera
is displayed.
22
Configuration and Operation
7.2 Home Page
With the exception of the model numbers, the CF-3211 and CF-4221 series have similar Home pages.
7.2.1 CF-3211/CF-4221 Camera Home Page
All models of the CF-3211/CF-4221 cameras include the following function buttons located on the
Home page, as shown in Figure 21.
Figure 21: Home Page Function Buttons
Display Size Adjustment (x1/x½)
The image display size can be adjusted to full-size or half-size.
Full Screen Mode (with Digital Zoom Control)
Click this button to view the monitored image in full screen mode. Use the mouse to
control zoom effects in Full Screen mode: scroll the mouse wheel (for zoom in/out),
and drag the mouse into any direction. Double-click on the screen to exit Full Screen
mode and return to the Home page.
Talk
The Talk button allows the local site to talk to the remote site. Click the button to
switch it on/off. This function is available only to a user who has been granted this
privilege by the Administrator. Refer to User in the Security section for further details.
Speaker
Press the Speaker button to mute/activate the audio. This function is available only to
a user who has been granted this privilege by the Administrator. Refer to User in the
Security section for further details.
Snapshot
Press this button to automatically save the JPEG snapshots in the specified location.
The default location to save snapshots is: C:\.To change the storage location, refer to
File Location.
23
Quasar CF-3211/CF-4221 User and Installation Guide
Note:
The System configuration page is accessible only by the Administrator.
Video Streaming Stop/Restart
Press the Stop button to disable video streaming and to display the live video as black.
Press Restart to show the live video again.
Recording
Pressing the Recording button stores recordings from the Live View in the location
specified on the local hard drive, which can be configured in the File Location screen.
The default storage location for the web recording is: C:/. Refer to File Location for
details.
7.3 System-Related Settings
The figure below shows all categories under the System tab. Each category in the sidebar is
explained in the following sections.
Figure 22: System Screen
24
Configuration and Operation
System
Security
Network
DDNS
Mail
FTP
HTTP
Application
Motion Detection
Network Failure
Detection
Tampering Alarm
Storage Management
Recording
Schedule
File Location
View Information
Factory Default
Software Version
Software Upgrade
Maintenance
Related Links
7.3.1 System
Click the System tab in the sidebar. The System page is displayed in Figure 22: System Screen. It
includes the following details:
Host Name
The host name is for camera identification. If the alarm function is enabled and is set to send an
alarm message by Mail/FTP, the host name entered here is displayed in the alarm message. See
Application.
Time Zone
Select the time zone from the drop-down menu.
Enable Daylight Saving Time
To enable DST, check the box and then specify time offset and DST duration. The format for time
offset is [hh:mm:ss]. For example, if the amount of time offset is one hour, enter 01:00:00 in the
field.
Time format
Enables a choice of formats: either year, month and day (yyyy/mm/dd) or day, month and year
(dd/mm/yyyy).
Sync with Computer Time
Select this button to synchronize video date and time display with the PC.
Manual
The Administrator can set video date, time and day manually. Entry format should be identical with
that shown next to the Enter field.
Sync with NTP Server
Network Time Protocol (NTP) is an alternate way to synchronize the camera’s clock with an NTP
server. Specify the server to synchronize in the Enter field. Then select an update interval from the
drop-down menu. For further information about NTP, visit www.ntp.org.
25
Quasar CF-3211/CF-4221 User and Installation Guide
User
HTTPS
IP Filter
IEEE 802.1X
7.3.2 Security
Clicking the Security tab in the System screen opens a drop-down menu with the tabs: User, HTTPS,
IP Filter and IEEE 802.1X.
Figure 23: Security Screen Tabs
Related Links
7.3.2.1 User
Click the User tab in the Security category on the sidebar to display user credentials.
Figure 24: Security Screen
26
Configuration and Operation
Note:
The following characters are valid: A-Z, a-z, 0-9,!#$%&’-.@^_~.
Note:
You must enter the user password and also select the authorized function(s).
When finished, click Save to modify the account authority.
Admin Password
Change the administrator’s password by entering the new password in both text boxes. The input
characters/numbers are displayed as dots for security purposes. After clicking Save, the web
browser asks the Administrator for the new password (maximum 14 digits).
Add user
The user name and passwords are limited to 14 characters. There is a maximum of 20 user accounts.
To add a new user:
1. Type the new user name and password in the respective fields.
2. Select the appropriate check boxes to give the user Camera Control, Talk and Listen
permissions.
I/O access – Basic functions that enable you to view video when accessing to the
camera.
Camera control – Allows you to change camera parameters on the Camera tab.
Talk/Listen – Talk and Listen functions allow the user at the local site to
communicate with the administrator at the remote site.
3. Click Add.
Manage User
To delete a user, pull down the user list and select the user name to delete. Click Delete to
remove it.
To edit a user, pull the user list down and select a user name. Click Edit to edit the user’s
password and privileges.
Figure 25: Editing Password and Privileges
27
Quasar CF-3211/CF-4221 User and Installation Guide
Note:
The self-signed certificate does not provide the same level of security as a
CA-issued certificate.
Figure 26: Modifying Account Authority
7.3.2.2 HTTPS
To use HTTPS on the camera, an HTTPS certificate must be installed. The HTTPS certificate can be
obtained either by creating and sending a certificate request to a Certificate Authority (CA) or by
creating a self-signed HTTPS certificate as described below.
HTTPS allows secure connections between the camera and web browser using Secure Socket Layer
(SSL) or Transport Layer Security (TLS) to protect camera settings and username/password info. A
self-signed certificate or a CA-signed certificate is required to implement HTTPS. Under the Security
category, click the HTTPS tab in the sidebar to display the following screen.
Figure 27: HTTPS Screen
28
Configuration and Operation
To create a self-signed certificate:
Before a CA-issued certificate is obtained, you can first create and install a self-signed certificate.
1. On the HTTPS page, click Create under Create self-signed certificate.
2. Provide the requested information to install a self-signed certificate for the camera. Refer to
Provide the Certificate Information in this section for details.
Figure 28: HTTPS Screen – Create Self-Signed Certificate
To create a certificate request:
1. Click the Create Certificate Request button to create and submit a certificate request in
order to obtain a signed certificate from a CA.
2. Provide the requested information in the Created Request field. Refer to Provide the
Certificate Information in this section for details.
3. When the request is complete, the subject of the Created Request is shown in the field. Click
Properties below the Subject field, copy the PEM-formatted request and send it to your CA.
Figure 29: HTTPS Screen – Install Signed Certificate
29
Quasar CF-3211/CF-4221 User and Installation Guide
To provide the certificate information:
To create a self-signed HTTPS certificate or a Certificate Request to CA, enter the information in the
Create a Self-signed Certificate screen. A definition of each of the requested fields follows.
Figure 30: Example of Self-Signed Certificate
Figure 31: Self-Signed Certificate – Details
4. Provide the requested information to install a self-signed certificate for the camera.
Country – Enter a two-letter combination code to indicate the specific country in which
the certificate will be used. For instance, type “US” to indicate United States.
State or province – Enter the local administrative region.
Locality – Enter other geographical information.
Organization – Enter the name of the organization to which the entity identified in
Common Name belongs.
Organizational Unit – Enter the name of the organizational unit to which the entity
identified in the Common Name field belongs.
30
Configuration and Operation
Note:
The self-signed certificate does not provide the same high level of security as a
Certificate Authorized (CA)-issued certificate.
Common Name – Indicate the name of the person or other entity that the certificate
identifies (often used to identify the website).
Valid days (self-signed certificate only) – Enter the period in days (1 ~ 9999) to indicate
the valid period of certificate.
5. Click OK to save the Certificate Information after completion.
7.3.2.3 IP Filter
The IP filter restricts access to the camera by denying/allowing specific IP addresses. Click the IP
filter tab under the category Security in the sidebar to display the following page.
Figure 32: IP Filter Screen
Enable IP Filter
1. Check the box to enable the IP Filter function. Once enabled, the listed IP addresses (IPv4) are
allowed/denied access to the camera.
2. Select Allow or Deny from the drop-down menu.
3. Click the Apply button to determine the IP Filter behavior.
Add/Delete IP Address
1. Enter the IP address in the Filtered IP Addresses text box.
2. Click Add to add a new filtered address. The Filtered IP Addresses box shows the currently
configured IP addresses. Up to 256 IP address entries may be specified.
3. To remove an IP address from the list, select the IP address and then click Delete.
31
Quasar CF-3211/CF-4221 User and Installation Guide
7.3.2.4 IEEE 802.1X
The camera is allowed to access a network protected by 802.1X/EAPOL (Extensible Authentication
Protocol over LAN). Users must contact the network administrator to obtain certificates, user IDs,
and passwords.
Figure 33: IEEE 802.1X/EAP-TLS Screen
CA Certificate
The CA certificate is created by the Certificate Authority for the purpose of validating itself. Upload
the certificate to check the server’s identity.
Client Certificate/Private Key
Upload the Client Certificate and Private Key to authenticate the camera.
Settings
Identity – Enter the user identity associated with the certificate. Up to 16 characters can be
used.
Private Key Password – Enter the password associated with the user identity. Up to 16
characters can be used.
Enable IEEE 802.1X
Check the box to enable IEEE 802.1X. Click Save to save the IEEE 802.1X/EAPTLS setting.
32
Configuration and Operation
Basic
QoS (Quality of Service)
SNMP Settings
UPnP
Note:
For future reference, record the camera’s MAC address, which is found on the camera
label.
7.3.3 Network
From the System screen, click the Network tab. A drop-down menu appears with tabs including
Basic, QoS, SNMP, and UPnP.
Figure 34: Network Screen
Related Links
7.3.3.1 Basic
You can connect to the camera with either fixed or dynamic (DHCP) IP address. The camera also
provides PPPoE (Point-to-Point Protocol over Ethernet) support for users who connect to the
network via PPPoE.
The screen is divided into three sections: General, Advanced and IPv6 Configuration. See Figure 34:
Network Screen.
1. General
Select one of the following options in the General area for configuring network settings:
Get IP address automatically (DHCP)
If you select Get IP address automatically, you can use the DNA utility, which is provided in the
supplied CD, to obtain the IP address. See Using the DNA Utility to Search and Access the Camera.
Use fixed IP address
The camera’s default setting is Use fixed IP address. You may use DNA or enter the IP address in your
browser’s URL address bar.
33
Quasar CF-3211/CF-4221 User and Installation Guide
Note:
MJPEG is not supported by Latitude.
Note:
Be sure to assign a different port number for each separate service mentioned
above.
To set up a new static IP address:
1. Select the Use fixed IP address option.
2. Enter the following information:
IP address – The IP address is necessary for network identification.
Subnet mask – Used to determine if the destination is in the same subnet. The default
value is 255.255.255.0.
Default gateway – Used to forward frames to destinations in a different subnet. An
invalid gateway setting causes transmission to destinations in other subnets to fail.
Primary DNS – The primary domain name server that translates host names into IP
addresses.
Secondary DNS – A secondary domain name server that backs up the primary DNS.
Use PPPoE – PPPoE users should enter their PPPoE user name and password into the
respective fields.
3. Click Save to confirm the settings.
2. Advanced
Enter the following advanced parameters in the Advanced section of the screen:
Web Server port – The default web server port is 80. Once the port is changed, the user must
be notified the change for the connection to be successful. For instance, when the
Administrator changes the HTTP port of the camera whose IP address is 192.168.0.100 from
80 to 8080, the user must type in the web browser http://192.168.0.100:8080 instead of
http://192.168.0.100.
RTSP port – The default setting of the RTSP port is 554. The range is from 1024 to 65535.
MJPEG over HTTP port – The default setting of MJPEG over HTTP port is 8008. The range is
from1024 to 65535.
HTTPS port – The default setting of HTTPS port is 443. The range is from 1024 to 65535.
MTU – The default setting of the MTU (Maximum Transmission Unit) is the greatest amount
of data that can be transferred in one physical frame on the network. For Ethernet, the
MTU is 1500 bytes. For PPPoE, the MTU is 1492. The range is from 700 to 1500 bytes.
Click Save to save the settings.
3. IPv6 Address Configuration
With IPv6 support, you can use the corresponding IPv6 address for browsing. Check Enable IPv6 to
enable this option. Click Save to save the settings.
34
Configuration and Operation
Note:
MJPEG is not supported by Latitude.
Note:
To enable this function, make sure the switches/routers in the network support QoS.
7.3.3.2 QoS (Quality of Service)
QoS provides differentiated service levels for different types of traffic packets and guarantees
delivery of priority services during periods of network congestion. Adapting the Differentiated
Services (DiffServ) model, traffic flows are classified and marked with DSCP (DiffServ Code point)
values, and as a result receive the corresponding forwarding treatment from DiffServ-capable
routers.
Figure 35: QoS Screen
DSCP Settings
The DSCP value range is from 0 to 63. The default DSCP value is 0 (DSCP disabled). The camera uses
the following QoS classes: Video, Audio, and Management.
Video DSCP – This class consists of applications such as MJPEG over HTTP, RTP/RTSP and
RTSP/HTTP.
Audio DSCP – The CF-3211/4221 cameras support audio.
Management DSCP – This class consists of HTTP traffic (web browsing).
Click Save when complete.
35
Quasar CF-3211/CF-4221 User and Installation Guide
7.3.3.3 SNMP Settings
Simple Network Management Protocol (SNMP) enables the camera to be monitored and managed
remotely by the network management system.
Figure 36: SNMP Settings Screen
SNMP v1/v2
Enable SNMP v1 or Enable SNMP v2 – Select the version of SNMP (v1 or v2) to use by
checking the relevant box.
Read Community – Specify the community name that has read-only access to all supported
SNMP objects. The default value is public.
Write Community – Specify the community name that has read/write access to all supported
SNMP objects (except read-only objects). The default value is private.
SNMP v3
SNMPv3 provides important security features including:
Confidentiality – Encryption of packets to prevent snooping by an unauthorized source.
Integrity – Message integrity to ensure that a packet has not been tampered with in transit
including an optional packet replay protection mechanism.
Authentication – To verify that the message is from a valid source.
To enable the SNMP v3 protocol, enter the appropriate data and passwords requested:
Enable SNMP v3 – Select the checkbox.
Security Name – See note below.
Authentication Type – Select MD5 or SHA from the drop-down menu. See note below.
Authentication Password – See note below.
Encryption Type – either DES or AES. See note below.
Encryption Password – See note below.
36
Configuration and Operation
Note:
You may have to consult with your System Administrator to activate this function.
Traps for SNMP v1/v2/v3
Traps are used by the camera to send messages to a management system for important events or
status changes.
Enable traps – Check this box to activate trap reporting.
Trap address – Enter the IP address of the management server.
Trap community – Enter the community to use when sending a trap message to the
management system. The default value is public.
Trap Option
Warm start – A warm start SNMP trap signifies that the SNMP device, such as the
camera, performs a software reload.
Click Save when complete.
7.3.3.4 UPnP
The UPnP page enables the Universal Plug-and-Play protocol on your network devices.
Figure 37: UPnP Screen
37
Quasar CF-3211/CF-4221 User and Installation Guide
Note:
To enable this function, make sure the UPnP component is installed on your
computer. Refer to Install UPnP Components for the Windows 7 and Windows
8 procedure.
Note:
To enable this function, make sure that your router supports UPnP and that it is
activated.
UPnP Setting
Enable UPnP – If UPnP is enabled and a camera is discovered on the LAN, the icon of the
connected camera appears in My Network Places, allowing direct access, as seen below.
Figure 38: Direct Access to Camera with UPnP Enabled
Enable UPnP port forwarding – When UPnP port forwarding is enabled, the camera is
allowed to open the web server port on the router automatically.
Friendly name – Set the name for the camera for identification.
Click Save to save the settings.
38
Configuration and Operation
7.3.4 DDNS
Dynamic Domain Name System (DDNS) allows a host name to be constantly synchronized with a
dynamic IP address. This permits those using a dynamic IP address to be accessed by a static domain
name.
Figure 39: DDNS Screen
Enable DDNS
Check this box to enable DDNS.
Provider – Select a DDNS host provider name from the drop-down menu.
Host name – Enter the registered domain name in the field.
Username/E-mail – Enter the username or e-mail address required by the DDNS provider for
authentication.
Password/Key – Enter the password or key required by the DDNS provider for
authentication.
Click Save to save the setting.
39
Quasar CF-3211/CF-4221 User and Installation Guide
7.3.5 Mail
The Administrator can send an e-mail via Simple Mail Transfer Protocol (SMTP) when an alarm is
triggered SMTP is a protocol for sending e-mail messages between servers. SMTP is a relatively
simple, text-based protocol, where one or more recipients of a message are specified and the
message text is transferred.
Two SMTP server accounts can be configured. Settings include SMTP Server, account name,
password, and e-mail address settings. Enter the details in the appropriate fields. For SMTP server
details, contact your network service provider. Click Save when finished. The following screen shows
the SMTP configuration.
Figure 40: Mail Screen – SMTP
40
Configuration and Operation
7.3.6 FTP
The Administrator can send an alarm message to one or two File Transfer Protocol (FTP) sites when
motion is detected. Settings include first and second server, server port, user name, password, and
remote folder. Enter the details in the appropriate fields. Click Save when finished. The following
screen shows the FTP settings.
Figure 41: FTP Screen
41
Quasar CF-3211/CF-4221 User and Installation Guide
7.3.7 HTTP
An HTTP notification server detects notification messages of triggered events sent from cameras.
Two notification server accounts (Alarm Triggered and Motion Detection) can be set up and sent to
the specified HTTP servers. Enter the HTTP details, including server, user name, and password, in the
appropriate fields. Click Save when finished. The settings are displayed in the HTTP screen below.
Figure 42: HTTP Screen
Refer to Send HTTP notification and Motion Detection for HTTP notification settings in the
Application section below.
42
Configuration and Operation
Pin No.
Designation
Terminal Block Alarm
Connections
1
Input (+)
2
Input (-)
3
Output (+)
4
Output (-)
7.3.8 Application
The Application screen enables control over the input and output alarms. If, for example, an event is
recognized by the system, an input or output alarm and message is generated.
Figure 43: Application Screen
The alarm input and output connectors are shown in the table below.
Table 5: Input/Output Alarm Connections
Alarm Switch
The Administrator can enable or disable the alarm function (Off/On).
Alarm Type
Select an alarm type (Normal close or Normal open) that corresponds to the alarm application.
43
Quasar CF-3211/CF-4221 User and Installation Guide
Note:
Make sure that local recording (with a microSD/SDHC card) is activated so that
this function can be implemented. See Recording for further details.
Alarm Output
Define the normal alarm output signal as Normal Close or Normal Open, according to the current
alarm application.
Triggered Action
The Administrator can specify various alarm actions to be taken when an alarm is triggered. The
options are listed below.
Enable alarm output – Select this box to enable alarm relay output.
Record stream to sd card – Select this box in order to save the alarm-triggered recording to
your microSD/SDHC card. Enter the number of seconds for the pre-trigger buffer. Select the
first radial button if you wish to upload for a specified length of time and enter the number
of seconds. Alternatively, select the second radial button to upload during the active trigger.
See Figure 44: Application – Record Stream to SD Card.
Figure 44: Application – Record Stream to SD Card
Send Message by FTP/E-Mail – Select whether to send an alarm message by FTP and/or
e-mail when an alarm is triggered.
44
Configuration and Operation
Note:
Make sure that SMTP or FTP configuration has been completed. See Mail and
FTP for further details.
Upload Image by FTP – As seen in the figure below, select this box to assign an FTP site and
configure the parameters shown. When an alarm is triggered, event images are uploaded to
the designated FTP site. Specify which one of two FTP addresses you wish to use from the
drop-down menu. Select the number of frames for the pre-trigger and post-trigger buffers
from the drop-down menu of 1-20 frames.
Figure 45: Application – Upload Image by FTP
Check the Continue image upload box if you wish to use this option. If you wish to specify
the length of time for the upload, click on this radial button and enter the number of
seconds. If you wish to upload during the active trigger, click on this radial button.
Finally, select the number of frames per second from the drop-down menu next to Image
frequency.
Upload Image by E-Mail – Select this box in order to assign an e-mail address and configure
various parameters as shown in the figure below. When the alarm is triggered, event images
are sent to one of two designated e-mail addresses. Select the number of frames for the pretrigger and post-trigger buffers from the drop-down menu of 1-20 frames.
Figure 46: Application – Upload Image by E-Mail
Check the box for Continue image upload if you wish to use this option. If you wish to specify
the length of time for the upload, click on this radial button and enter the number of
seconds. If you wish to upload during the active trigger, click on this radial button.
Finally, select the number of frames per second from the drop-down menu next to Image
frequency.
45
Quasar CF-3211/CF-4221 User and Installation Guide
Send HTTP notification – Check this box to specify the destination HTTP address and
parameters for event notifications by the triggered alarm. When an alarm is triggered, the
notification will be sent to one of two specified HTTP servers. See figure below.
Figure 47: Application – Send HTTP Notification
File Name
File Name – Enter a file name in the field, for example image.jpg. The uploaded image’s file
name format is set in this section. Select one that meets your requirements.
Add date/time suffix
File name: imageYYMMDD_HHNNSS_XX.jpg
Y: Year, M: Month, D: Day
H: Hour, N: Minute, S: Second
X: Sequence Number
Add sequence number suffix (no maximum value)
File name: imageXXXXXXX.jpg
X: Sequence Number
Add sequence number suffix (limited value)
File Name: imageXX.jpg
X: Sequence Number
The file name suffix ends at the number being set. For example, if the setting is up to
“10,” the file name will start from 00, end at 10, and then start over again.
Overwrite
The original image in the FTP site will be overwritten by the new uploaded file with a
static filename.
After entering all the settings, click Save.
46
Configuration and Operation
7.3.9 Motion Detection
The motion detection function detects suspicious motion and triggers alarms when motion volume
in the detected area reaches/exceeds the determined sensitivity threshold value.
Figure 48: Motion Detection Screen
Within the Live View pane on the Motion Detection screen, there is a frame (Motion Detection
window) which is used for defining the motion detection area. To change the size of the Motion
Detection window, move the mouse cursor to the edge of the frame and drag it outward/inward.
Moving the mouse to the center of the frame shifts the frame to the intended location.
Motion Detection Activation
It is possible to define up to four motion detection zones within the Motion Detection window by
selecting a number from the drop-down menu.
The motion detection function may be turned on or off in the Motion Detection section of the
screen. The default setting is Off.
47
Quasar CF-3211/CF-4221 User and Installation Guide
By Schedule
For instructions how to set a schedule for motion detection, refer to Schedule. Below is a screen
showing the Schedule drop-down menu with selected schedules.
Figure 49: Motion Detection Screen – with Schedule Drop-Down Menu
Motion Detection Windows
Up to 10 Motion Detection windows can be set. Press the add button under the Live View pane to
add a Motion Detection window. To cancel a Motion Detection window, move the mouse cursor to
the selected window and click delete.
If the motion detection function is activated, the following Motion pop-up window appears.
When motion is detected, the signals are displayed in the Motion window shown below.
48
Configuration and Operation
Note:
Make sure the local recording (with microSD/SDHC card) is activated so that this
function can be implemented. See Recording for further details.
Detailed settings for motion detection are as follows:
Sampling pixel interval [1-10] – Select a number from 1-10. The default value is 1. If the
value is set as 3, within the detection region, the system will take one sampling pixel for
every 3 pixels by each row and each column (see the figure below).
Detection level [1-100] – Select a number from 1-100. The default level is 40. This sets
detection level for each sampling pixel; the smaller the value, the more sensitive it is.
Sensitivity level [1-100] – Select a number from 1-100. The default level is 80, which means if
20% or more sampling pixels are detected differently, the system will detect motion. The
bigger the value, the more sensitive it is. When the value is bigger, the red horizontal line in
the motion indication window will be lowered accordingly.
Time interval (sec) [0-7200] – Select a number from 0-7200 (seconds). The default interval is
10. The value is the interval between each detected motion.
Triggered Action
The Administrator can specify alarm actions to be taken when motion is detected. The options are
listed as follows:
Enable alarm output – Check this box and select the predefined type of alarm output (low or
high) to enable alarm relay when tampering is detected.
Record stream to sd card – Select this box to store the motion detection alarm recording in a
microSD/SDHC card when tampering is detected. Enter the number of seconds for the pretrigger buffer. Select the first radial button to upload for a specified length of time and enter
the number of seconds. Alternatively, select the second radial button to upload during the
active trigger. See Figure 44: Application – Record Stream to SD Card.
Send Alarm Message by FTP/E-Mail – Select whether to send an alarm message by FTP
and/or e-mail when motion is detected.
Upload Image by FTP – Select this box in order to upload an image to a designated FTP site
when motion is detected according to various parameters, as seen in Figure 45: Application
– Upload Image by FTP. Specify the FTP address to use from the drop-down menu. Select the
number of frames for the pre-trigger and post-trigger buffers from the drop-down menu of
1-20 frames.
Check the box for Continue image upload if you wish to use this option. To specify the length
of time for the upload, click on this radial button and enter the number of seconds. To
upload during the active trigger, click on this radial button. Finally, select the number of
frames per second from the drop-down menu next to Image frequency.
49
Quasar CF-3211/CF-4221 User and Installation Guide
Note:
Make sure that SMTP or FTP configuration has been completed. See Mail and
FTP for further details.
Note:
Make sure that local recording (with a microSD/SDHC card) is activated so that
this function can be implemented. See Recording for further details.
Upload Image by E-Mail – Select this box in order to assign an e-mail address and configure
various parameters, as seen in Figure 46: Application – Upload Image by E-Mail. When
motion is detected, event images are sent to one of two designated e-mail addresses. Select
the number of frames for the pre-trigger and post-trigger buffers from the drop-down menu
of 1-20 frames.
Check the box for Continue image upload to use this option. To specify the length of time for
the upload, click on this radial button and enter the number of seconds. To upload during
the active trigger, click on this radial button. Finally, select the number of frames per second
from the drop-down menu next to Image frequency.
Send HTTP notification – Check this box to send a notification by HTTP. Select the destination
HTTP address from the drop-down menu and specify the parameters for event notifications
by motion detection triggered. When an alarm is triggered, the notification will be sent to
one of two specified HTTP servers. See Figure 47: Application – Send HTTP Notification.
File Name
The uploaded image’s filename format is set in this section. Select one that meets your
requirements.
Save
Click Save to save the motion detection settings.
50
Configuration and Operation
7.3.10 Network Failure Detection
The network failure detection function allows the IP camera to periodically ping another IP device
within the network to detect a network failure, for example, if a video server is disconnected. By
implementing local recording (through a microSD/SDHC card) if a network failure occurs, the camera
can operate as a backup recording device for the surveillance system.
Figure 50: Network Failure Detection Screen
Detection Switch
The Administrator can enable or disable the detection function by selecting On or Off.
By Schedule
For instructions how to set a schedule for network failure detection, refer to Schedule.
Detection Type
In the text box, enter the IP address to ping and the time interval in minutes between pings.
Triggered Action
The Administrator can specify various alarm actions to be taken when an alarm is triggered. The
options are listed below.
Enable alarm output – Check this box and select the predefined type of alarm output (low or
high) to enable alarm relay when tampering is detected.
Record stream to sd card -– Select this box in order to save the alarm-triggered recording
into a microSD/SDHC card. Enter the number of seconds for the pre-trigger buffer. Select the
first radial button to upload for a specified length of time and enter the number of seconds.
Alternatively, select the second radial button to upload during the active trigger. See Figure
44: Application – Record Stream to SD Card.
51
Quasar CF-3211/CF-4221 User and Installation Guide
Note:
Make sure that local recording (with a microSD/SDHC card) is activated so that this
function can be implemented. See Recording for further details.
Send message by FTP/E-Mail – Select whether to send an alarm message by FTP and/or e-
mail when a network failure is detected.
Save
Click Save to save the network failure detection settings.
7.3.11 Tampering Alarm
The Tampering Alarm function helps the IP camera deal with tampering (such as, deliberate
redirection, blocking, paint-spraying, and obscuring the lens, etc.). Using video analysis, the camera
can react to such events by sending out notifications or uploading snapshots to the specified
destination(s).
Figure 51: Tampering Alarm Screen
Detection of camera tampering is achieved by measuring the differences between the older frames
of video (which are stored in buffers) and more recent frames.
Tampering Alarm
The tampering alarm function may be turned on or off in the Tampering Alarm page. The default
setting is Off.
By Schedule
For instructions how to set a schedule for the tampering alarm, refer to Schedule.
52
Configuration and Operation
Note:
Make sure the local recording (with a microSD/SDHC card) is activated so that
this function can be implemented. See Recording for further details.
Note:
Make sure that SMTP or FTP configuration has been completed. See Mail and
FTP for further details.
Tampering Duration
The minimum Tampering Duration is the time for video analysis to determine whether camera
tampering has occurred. Minimum duration could also be interpreted as defining the tampering
threshold; a longer duration represents a higher threshold. The tampering duration time range is
from 10 to 3600 seconds.
Triggered Action
The Administrator can specify multiple alarm actions to be taken when tampering is detected. All
options are listed as follows:
Enable alarm output – Check this box and select the predefined type of alarm output
(high or low) to enable alarm relay when tampering is detected.
Record stream to sd card – Select this box in order to save the alarm-triggered recording
into a microSD/SDHC card. Enter the number of seconds for the pre-trigger buffer. Select
the first radial button to upload for a specified length of time and enter the number of
seconds. Alternatively, select the second radial button to upload during the active trigger.
See Figure 44: Application – Record Stream to SD Card.
Send Alarm Message by FTP/E-Mail – The Administrator can select whether to send an
alarm message by FTP and/or E-Mail when tampering is detected.
Upload Image by FTP – Selecting this option enables you to assign an FTP site and
configure various parameters, as shown in Figure 45: Application – Upload Image by FTP.
When tampering is detected, event images will be uploaded to the designated FTP site.
Specify the FTP address to use from the drop-down menu. Select the number of frames
for the pre-trigger and post-trigger buffers from the drop-down menu of 1-20 frames.
Check the box for Continue image upload if you wish to use this option. To specify the
length of time for the upload, click on this radial button and enter the number of
seconds. To upload during the active trigger, click on this radial button. Finally, select the
number of frames per second from the drop-down menu next to Image frequency.
Upload Image by E-Mail – Selecting this option enables you to assign an e-mail address
and configure various parameters, as shown in Figure 46: Application – Upload Image by
E-Mail. When tampering is detected, event images will be sent to the designated e-mail
address.
Specify two e-mail addresses to use from the drop-down menu. Select the number of
frames for the pre-trigger and post-trigger buffers from the drop-down menu of 1-20
frames.
Check the box for Continue image upload if you wish to use this option. To specify the
length of time for the upload, click on this radial button and enter the number of
seconds. To upload during the active trigger, click on this radial button. Finally, select the
number of frames per second from the drop-down menu next to Image frequency.
53
Quasar CF-3211/CF-4221 User and Installation Guide
Note:
Format the microSD/SDHC card when using it for the first time. Formatting is also
required when a memory card has been used on one camera and is then transferred to a
camera that uses a different software platform.
Send HTTP notification – Check this option, select the destination HTTP address, and
specify the parameters for HTTP notifications. When the tampering alarm is triggered, the
HTTP notifications can be sent to the specified HTTP server. See Figure 47: Application –
Send HTTP Notification.
File Name
The uploaded image’s filename format can be set in this section. Select the one that meets your
requirements.
Save
Click Save to save all the specified tampering alarm settings.
7.3.12 Storage Management
You can locally record up to 32GB on a microSD/SDHC card. The Storage Management page shows
the capacity information of the card and a recording list of all the recording files saved on the
memory card. You can also format the card and implement automatic recording cleanup on this
page. To implement microSD/SDHC card recording, see Recording.
Figure 52: Storage Management Screen
Device information
Upon inserting the microSD/SDHC card, card information, such as the memory capacity and status, is
displayed.
54
Configuration and Operation
Note:
The capital letters: R, N, A, (A0), M, (M0) followed by an underscore, appear at
the beginning of the file name. They denote the type of recording.
R - Regular (always or schedule)
N - Network failure
M - Motion, (M0 refers to the first motion window trigger)
A - Alarm (A0 refers to the first alarm trigger input).
Device setting
Click Format to format the memory card.
Disk cleanup setting
Enable automatic recording cleanup by selecting Enable automatic disk cleanup. From the pull-down
menu, specify the minimum length of time over which to remove recordings. For example, remove
recordings over 10 days old. Enter the percent of disk capacity used in order to remove the oldest
recordings. Click Save when finished.
Recording List
Each video file on the microSD/SDHC card is listed in the Recording list below. The maximum file size
is 60 MB per file. See Recording for further details.
When the recording mode is set as Always (consecutive recording) and the microSD/SDHC card
recording is enabled by events triggered, the system immediately saves a recorded event on the
memory card once an event occurs. Then the camera will return to the regular recording mode after
events recording.
Figure 53: Video File Recording List
Remove – To remove a file, first select the file and then click Remove.
Sort – Click Sort to list the files in the Recording list in order of name and date.
55
Quasar CF-3211/CF-4221 User and Installation Guide
Download – To open/download a video clip, first select the file and then click download. The
selected file window pops up as shown below. Click on the AVI file to play the video in the
player or download it to a specified location.
Figure 54: Selected File Window
7.3.13 Recording
In the Recording screen, specify the recording schedule. Select one of three options:
Disable – Disable this function
Always – Always use this function
Only during time frame – Records only during a specified time frame
56
Figure 55: Recording Screen
Configuration and Operation
Note:
This option works only if the microSD/SDHC card is installed in the camera.
Note:
This application is not the same as the Recording Schedule function.
Activating microSD/SDHC card recording
Two types of schedule mode are available: Always and Time Frame setting. You can setup the time
frame to fit the recording schedule by selecting the day(s), start time and duration for recording.
Choosing Always activates the microSD/SDHC card recording all the time. Click Save to confirm the
schedule mode.
Terminating microSD/SDHC card recording
Select Disable to terminate the recording function.
7.3.14 Schedule
The Schedule screen is used by the network failure detection, tampering and motion detection
functions. To access the schedule function, open the Main window, select the System tab, and click
on the Schedule tab. The functions in this tab allow administrators to create customized schedules
for the camera using this option. If a schedule exists, the administrator can apply that schedule to
this camera using the available dropdown. See Figure 56: Schedule Screen
Figure 56: Schedule Screen
57
Quasar CF-3211/CF-4221 User and Installation Guide
Note:
Make sure the selected file path contains valid characters.
To create a new schedule or edit an existing schedule
1. Click on the appropriate checkboxes relating to the days of the week (Sun, Mon, Tue,
Wed, Thu, Fri and Sat) to create a schedule. Tuesday (Tue) is checked in the example.
2. Set Start time (for example, 09:00) and Duration (for example, 4:00 hours).
3. Click Save to apply the newly created schedule to the camera.
To remove a schedule:
1. Select the setup data line by line and use Delete to remove.
7.3.15 File Location
From the File Location page, specify a storage location for snapshots and web recordings. The
default setting is: C:\. After confirming the setting, click Save to save the snapshots and recordings in
the designated location.
Figure 57: File Location Screen
58
Configuration and Operation
Log File
User Information
View Parameters
7.3.16 View Information
Clicking the View Information tab in the System screen opens a drop-down menu with tabs: Log
File, User Information, and Parameters.
Figure 58: System Log Screen
Related Links
7.3.16.1 View Log File
Click on Log file to view the system log file. The content of the file provides information about
connections after system boot-up. See Figure 58: System Log Screen.
59
Quasar CF-3211/CF-4221 User and Installation Guide
7.3.16.2 User Information
The Administrator can view each user’s login information and privileges in the User information
screen shown below.
View User Login Information
Click get user information to see each user’s details. For example: Admin: 1234. This indicates that
the user’s login username is Admin and the password is 1234.
Figure 59: User Information Screen
60
View User Privilege
Note:
The example above shows the maximum privileges that can be granted. It is however,
dependent on the specific user security level.
Click get user privacy to view each user’s privileges.
Configuration and Operation
Figure 60: User Information – Privileges Screen
In Figure 60, the user Admin is granted privileges of I/O access, Camera control, Talk and Listen.
61
Quasar CF-3211/CF-4221 User and Installation Guide
Note:
Slide the sidebar located on the right of the screen to view the entire list of parameters.
7.3.16.3 View Parameters
The Parameter screen enables viewing all of the system’s parameter settings.
Figure 61: Parameter List Screen
7.3.17 Factory Default
The Factory default page is shown below. Follow the instructions to reset the camera to factory
default settings if needed.
Figure 62: Factory Default Screen
62
Configuration and Operation
Note:
The IP address and all other settings will be restored to factory default settings.
Full Restore
Click Full Restore to restore the factory default settings. The system restarts in 30 seconds.
Partial Restore
Click Partial Restore to restore the factory default settings, but save the network settings. The
system restarts in 30 seconds.
Figure 63: Partial Restore Screen
Reboot
Clicking Reboot restarts the system without changing current settings.
7.3.18 Software Version
The current version of software is displayed in the Software version screen.
Figure 64: Software Version Screen
63
Quasar CF-3211/CF-4221 User and Installation Guide
Note:
Make sure that the software upgrade file is available before performing a software
upgrade.
Note:
Do not change the upgrade file name or the system will fail to find the
file.
7.3.19 Software Upgrade
The Upgrade screen is shown below.
To upgrade the software:
1. In the Step 1 text box, click Browse and select the binary file to be uploaded, for
example, uImage+userland.img.
2. From the drop-down menu of binary files in Step 2, select the file to upgrade. In the
above example uImage+userland.img is selected.
Figure 65: Software Upgrade Screen
64
Configuration and Operation
Warning:
Do not unplug power while upgrading software.
3. Click Upgrade. The system verifies that the upgrade file exists and begins to upload
the file. The upgrade status bar is displayed on the page. After the upgrade process
has finished, the Home page is displayed.
Figure 66: Software Upgrade – In Process
4. Close the video browser.
5. From the Windows Start menu, select the Control Panel.
6. Select Uninstall a Program.
7. In the Currently installed programs list, select DCViewer.
8. Click Uninstall to delete the existing DCViewer.
9. Install the new DCViewer ActiveX plug-in.
65
Quasar CF-3211/CF-4221 User and Installation Guide
Warning:
Do not unplug power while changing file names.
Warning:
Do not unplug power while changing file names.
7.3.20 Maintenance
You can export configuration files to a specified location and retrieve data by uploading an existing
configuration file to the camera.
Figure 67: Maintenance Screen
Export
You can save system settings by exporting the configuration file (.bin) to a specified location for
future use. Press Export and the popup window File Download appears as shown below.
Figure 68: File Download Screen
Click Save and specify a location to save the configuration file.
Upload
To copy an existing configuration file to the camera, click Browse to select the configuration file, and
then click Upload to upload the file.
66
Configuration and Operation
Video Format
Video Compression
Video OCX Protocol
Video Frame Rate
Video Mask
Audio
7.4 Video and Audio Streaming Settings
Select the Streaming tab in the navigation bar at the top of the page to display the configurable
video and audio selections in the sidebar. From the Streaming sidebar, the Administrator can
configure specific video resolution, video compression mode, video protocol, audio transmission
mode, etc. Further details of these settings are specified in the following sections.
The following video resolutions are supported:
H.264 + H.264
MJPEG + H.264
MJPEG only
H.264 only
Related Links
7.4.1 Video Format
From the Video Format screen, you can configure the following settings:
CF-3211 NTSC Video Resolution Settings
CF-3211 PAL Video Resolution Settings
CF-4221 NTSC Video Resolution Settings
CF-4221 PAL Video Resolution Settings
Text Overlay Settings
Video Rotate Type
GOV Settings
H.264 Profile
Figure 69: Video Format Screen
67
Quasar CF-3211/CF-4221 User and Installation Guide
H.264
MJPEG
BNC Support
1280 x 1024 (15fps)
1280 x 1024 (15fps)
√
1280 x 720 (15fps)
-
1024 x 768 (15fps)
-
800 x 600 (30fps)
-
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
1280 x 720 (30fps)
1280 x 720 (30fps)
√
1024 x 768 (30fps)
-
800 x 600 (30fps)
-
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
1024 x 768 (30fps)
1024 x 768 (30fps)
√
800 x 600 (30fps)
-
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
800 x 600 (30fps)
800 x 600 (30fps)
√
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
720 x 480 (30fps)
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
640 x 480 (30fps)
640 x 480 (30fps)
√
352 x 240 (30fps)
√
352 x 240 (30fps)
352 x 240 (30fps)
-
Note:
MJPEG is not supported by Latitude.
7.4.1.1 CF-3211 NTSC Video Resolution Settings
The following tables contain video resolution settings for an NTSC TV system.
MJPEG + H.264 Video Resolution (NTSC):
68
H.264 + H.264 Video Resolution (NTSC):
H.264-1
H.264-2
BNC Support
1280 x 1024 (30fps)
1280 x 1024 (15fps)
√
1280 x 720 (15fps)
-
1024 x 768 (15fps)
-
800 x 600 (30fps)
-
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
1280 x 720 (30fps)
1280 x 720 (30fps)
√
1024 x 768 (30fps)
-
800 x 600 (30fps)
-
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
1024 x 768 (30fps)
1024 x 768 (30fps)
√
800 x 600 (30fps)
-
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
800 x 600 (30fps)
800 x 600 (30fps)
√
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
720 x 480 (30fps)
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
640 x 480 (30fps)
640 x 480 (30fps)
√
352 x 240 (30fps)
√
352 x 240 (30fps)
352 x 240 (30fps)
-
MJPEG
BNC Support
1280 x 1024 (30fps)
√
1280 x 720 (30fps)
√
1024 x 768 (30fps)
√
800 x 600 (30fps)
√
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
-
Note:
MJPEG is not supported by Latitude.
H.264
BNC Support
1280 x 1024 (30fps)
√
1280 x 720 (30fps)
√
1024 x 768 (30fps)
√
800 x 600 (30fps)
√
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
-
Configuration and Operation
MJPEG Only Video Resolution (NTSC):
H.264 Only Video Resolution (NTSC):
69
Quasar CF-3211/CF-4221 User and Installation Guide
H.264
MJPEG
BNC Support
1280 x 1024 (25fps)
1280 x 1024 (13fps)
√
1280 x 720 (13fps)
-
1024 x 768 (13fps)
-
800 x 600 (25fps)
-
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
1280 x 720 (25fps)
1280 x 720 (25fps)
√
1024 x 768 (25fps)
-
800 x 600 (25fps)
-
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
1024 x 768 (25fps)
1024 x 768 (25fps)
√
800 x 600 (25fps)
-
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
800 x 600 (25fps)
800 x 600 (25fps)
√
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
720 x 576 (25fps)
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
640 x 480 (25fps)
640 x 480 (25fps)
√
352 x 288 (25fps)
√
352 x 288 (25fps)
352 x 288 (25fps)
-
Note:
MJPEG is not supported by Latitude.
7.4.1.2 CF-3211 PAL Video Resolution Settings
The following tables contain video resolution settings for a PAL system.
MJPEG + H.264 Video Resolution (PAL):
70
H.264 + H.264 Video Resolution (PAL):
H.264-1
H.264-2
BNC Support
1280 x 1024 (25fps)
1280 x 1024 (13fps)
√
1280 x 720 (13fps)
-
1024 x 768 (13fps)
-
800 x 600 (25fps)
-
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
1280 x 720 (25fps)
1280 x 720 (25fps)
√
1024 x 768 (25fps)
-
800 x 600 (25fps)
-
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
1024 x 768 (25fps)
1024 x 768 (25fps)
√
800 x 600 (25fps)
-
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
800 x 600 (25fps)
800 x 600 (25fps)
√
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
720 x 576 (25fps)
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
640 x 480 (25fps)
640 x 480 (25fps)
√
352 x 288 (25fps)
√
352 x 288 (25fps)
352 x 288 (25fps)
-
MJPEG
BNC Support
1280 x 720 (25fps)
√
1024 x 768 (25fps)
√
800 x 600 (25fps)
√
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
-
Note:
MJPEG is not supported by Latitude.
H.264
BNC Support
1280 x 1024 (25fps)
√
1280 x 720 (25fps)
√
1024 x 768 (25fps)
√
800 x 600 (25fps)
√
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
-
Configuration and Operation
MJPEG Only Video Resolution (PAL):
H.264 Only Video Resolution (PAL):
71
Quasar CF-3211/CF-4221 User and Installation Guide
H.264
MJPEG
BNC Support
1920 x 1080 (30fps)
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
1920 x 1080 (15fps)
1920 x 1080 (15fps)
√
1280 x 1024 (30fps)
-
1280 x 720 (30fps)
-
1024 x 768 (30fps)
-
800 x 600 (30fps)
-
1280 x 1024 (30fps)
1280 x 1024 (30fps)
√
1280 x 720 (30fps)
-
1024 x 768 (30fps)
-
800 x 600 (30fps)
-
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
1024 x 768 (30fps)
1024 x 768 (30fps)
√
800 x 600 (30fps)
-
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
800 x 600 (30fps)
800 x 600 (30fps)
√
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
720 x 480 (30fps)
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
640 x 480 (30fps)
640 x 480 (30fps)
√
352 x 240 (30fps)
√
352 x 240 (30fps)
352 x 240 (30fps)
-
Note:
MJPEG is not supported by Latitude.
7.4.1.3 CF-4221 NTSC Video Resolution Settings
The following tables are video resolution settings for an NTSC TV system.
MJPEG + H.264 Video Resolution (NTSC):
72
H.264-1
H.264-2
BNC Support
1920 x 1080 (30fps)
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
1920 x 1080 (15fps)
1920 x 1080 (15fps)
√
1280 x 1024 (30fps)
-
1280 x 720 (30fps)
-
1024 x 768 (30fps)
-
800 x 600 (30fps)
-
1280 x 1024 (30fps)
1280 x 1024 (15fps)
√
1280 x 720 (30fps)
-
1024 x 768 (30fps)
-
800 x 600 (30fps)
-
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
1280 x 720 (30fps)
1280 x 720 (30fps)
√
1024 x 768 (30fps)
-
800 x 600 (30fps)
-
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
1024 x 768 (30fps)
1024 x 768 (30fps)
√
800 x 600 (30fps)
-
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
800 x 600 (30fps)
800 x 600 (30fps)
√
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
720 x 480 (30fps)
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
√
640 x 480 (30fps)
640 x 480 (30fps)
√
352 x 240 (30fps)
√
352 x 240 (30fps)
352 x 240 (30fps)
-
MJPEG
BNC Support
1920 x 1080 (30fps)
√
1280 x 1024 (30fps)
√
1280 x 720 (30fps)
√
1024 x 768 (30fps)
√
800 x 600 (30fps)
√
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
-
Note:
MJPEG is not supported by Latitude.
H.264 + H.264 Video Resolution (NTSC):
Configuration and Operation
MJPEG Only Video Resolution (NTSC):
73
Quasar CF-3211/CF-4221 User and Installation Guide
BNC Support
1920 x 1080 (30fps) Low Latency
-
1920 x 1080 (30fps)
√
1280 x 1024 (30fps)
√
1280 x 720 (30fps)
√
1024 x 768 (30fps)
√
800 x 600 (30fps)
√
720 x 480 (30fps)
√
640 x 480 (30fps)
√
352 x 240 (30fps)
-
H.264
MJPEG
BNC Support
1920 x 1080 (13fps)
1920 x 1080 (13fps)
√
1280 x 1024 (25fps)
-
1280 x 720 (25fps)
-
1024 x 768 (25fps)
-
800 x 600 (25fps)
-
1920 x 1080 (25fps)
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
1280 x 1024 (25fps)
1280 x 1024 (25fps)
√
1280 x 720 (25fps)
-
1024 x 768 (25fps)
-
800 x 600 (25fps)
-
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
1280 x 720 (25fps)
1280 x 720 (25fps)
√
1024 x 768 (25fps)
-
800 x 600 (25fps)
-
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
1024 x 768 (25fps)
1024 x 768 (25fps)
√
800 x 600 (25fps)
-
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
800 x 600 (25fps)
800 x 600 (25fps)
√
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
720 x 576 (25fps)
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
640 x 480 (25fps)
640 x 480 (25fps)
√
352 x 288 (25fps)
√
352 x 288 (25fps)
352 x 288 (25fps)
-
Note:
MJPEG is not supported by Latitude.
H.264 Only Video Resolution (NTSC):
7.4.1.4 CF-4221 PAL Video Resolution Settings
The following tables are video resolution settings for a PAL system.
MJPEG + H.264 Video Resolution (PAL):
74
H.264 + H.264 Video Resolution (PAL):
H.264-1
H.264-2
BNC Support
1920 x 1080 (13fps)
1920 x 1080 (13fps)
√
1280 x 1024 (25fps)
-
1280 x 720 (25fps)
-
1024 x 768 (25fps)
-
800 x 600 (25fps)
-
1920 x 1080 (25fps)
1920 x 1080 (25fps)
√
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
1280 x 1024 (25fps)
1280 x 1024 (13fps)
√
1280 x 720 (13fps)
-
1024 x 768 (25fps)
-
800 x 600 (25fps)
-
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
1280 x 720 (25fps)
1280 x 720 (25fps)
√
1024 x 768 (25fps)
-
800 x 600 (25fps)
-
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
1024 x 768 (25fps)
1024 x 768 (25fps)
√
800 x 600 (25fps)
-
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
800 x 600 (25fps)
800 x 600 (25fps)
√
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
720 x 576 (25fps)
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
√
640 x 480 (25fps)
640 x 480 (25fps)
√
352 x 288 (25fps)
√
352 x 288 (25fps)
352 x 288 (25fps)
-
MJPEG
BNC Support
1920 x 1080 (25fps)
√
1280 x 1024 (25fps)
√
1280 x 720 (25fps)
√
1024 x 768 (25fps)
√
800 x 600 (25fps)
√
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
-
Note:
MJPEG is not supported by Latitude.
Configuration and Operation
MJPEG Only Video Resolution (PAL):
75
Quasar CF-3211/CF-4221 User and Installation Guide
H.264
BNC Support
1920 x 1080 (25fps) Low Latency
-
1920 x 1080 (25fps)
√
1280 x 1024 (25fps)
√
1280 x 720 (25fps)
√
1024 x 768 (25fps)
√
800 x 600 (25fps)
√
720 x 576 (25fps)
√
640 x 480 (25fps)
√
352 x 288 (25fps)
-
H.264 Only Video Resolution (PAL):
7.4.1.5 Text Overlay Settings
Users can select the items to display data including date/time/text on the Live Video pane. The
maximum length of the string is 20 alphanumeric characters. Click Save to confirm the Text Overlay
setting.
7.4.1.6 Video Rotate Type
You can change video display type if necessary. Selectable video rotate types include Normal video,
Flip video, Mirror video, 90 degree clockwise, 180 degree rotate, and 90 degree counterclockwise.
Differences among these types are illustrated below. The following drop-down menu appears when
selecting this option.
76
Figure 70: Video Rotate Type Screen
Configuration and Operation
Suppose the displayed image of the camera is as follows.
Figure 71: View-1 (Source)
To rotate the image vertically, for example, select Flip video. The displayed image is reversed as
shown below.
Figure 72: View-2 Image Rotated Vertically (Reversed)
Following are descriptions of different video rotate types.
Normal video – The image appears as it is viewed.
Flip video – The image is reversed along its horizontal axis.
Mirror video – The image is reversed along its vertical axis.
90 degree clockwise – The image rotates 90° clockwise (to the right).
180 degree rotate – The image rotates 180° counter-clockwise (to the left).
90 degree counterclockwise – The image rotates 90° counter-clockwise (to the left).
Click Save to confirm the setting.
7.4.1.7 GOV Settings
You can set the GOV length to determine the frame structure (I-frames and P-frames) in a video
stream for saving bandwidth. The setting range is from 2 to 64. A longer GOV means decreasing the
frequency of I-frames. Click Save to confirm the GOV setting.
7.4.1.8 H.264 Profile
The H.264 standard defines 21 sets of capabilities. These are referred to as profiles and they target
specific classes of applications. In the security industry, the most common are as follows:
Baseline Profile (BP)
Primarily for low-cost applications that require additional data loss robustness, Baseline
Profile is used in some videoconferencing and mobile applications. This is the most common
profile used in IP security cameras due to the low computational cost of processing the video
using this profile.
77
Quasar CF-3211/CF-4221 User and Installation Guide
Note:
MJPEG is not supported by Latitude.
Note:
The second stream is limited to 2048 kbps.
Main Profile (MP)
This profile provides improved picture quality at reduced bandwidths and storage costs and
is becoming more common as the camera processors (DSPs) become more able to handle
the processing load. Main Profile can save 10-30% over Baseline.
High Profile (HP)
High Profile is the primary profile for HD broadcast and Blu-ray HD disc media applications. It
can save 10-30% of the storage cost over Main Profile. However, it may also increase video
latency, depending on the stream structure. Quasar models default to the Main Profile to
provide the best trade-off between storage size and video latency.
Click Save to confirm the settings.
7.4.2 Video Compression
From the Video Compression page, you can specify MJPEG/H.264 compression settings.
Figure 73: Video Compression Screen
MJPEG Compression Setting
A higher value implies higher bit rates and higher visual quality. The default setting of the MJPEG Q
factor is 35. The setting range is from 1 to 70. Click Save to confirm the setting.
H.264-1/H.264-2 Compression Setting
The default setting of H.264-1/H.264-2 is 4096/1024 kbps. The setting range is from 64 to 8192 kbps.
Click Save to confirm the setting.
Compression Information Setting
Select the checkbox to display compression information on the Home page. Click Save to confirm the
setting.
78
Configuration and Operation
Note:
CBR mode affects image quality.
Note:
MJPEG is not supported by Latitude.
CBR Mode Setting
If available bandwidth is limited, CBR (Constant Bit Rate) mode can be selected. To operate the
camera in Variable Bit Rate (VBR) mode, uncheck the CBR checkbox. Click Save to confirm the
setting.
7.4.3 Video OCX Protocol
From the Video OCX Protocol page, you can select various protocols for streaming media over the
network. In the case of multicast networking, select Multicast mode.
Figure 74: Video OCX Protocol Screen
Video OCX protocol setting options include:
RTP over UDP
RTP over RTSP (TCP)
RTSP over HTTP
MJPEG over HTTP
Multicast mode – Enter in each field all required data, including Multicast IP address, H.264-
1 video port, H.264-2 video port, MJPEG video port, MJPEG audio port, and Multicast TTL.
Click Save to confirm the settings.
79
Quasar CF-3211/CF-4221 User and Installation Guide
Note:
MJPEG is not supported by Latitude.
Note:
A lower frame rate decreases video smoothness.
7.4.4 Video Frame Rate
From the Video Frame Rate screen, you can specify the frames per second (fps) for each video
compression format.
Figure 75: Video Frame Rate Screen
MJPEG/H.264-1/H.264-2 Frame Rate Setting
The default setting of the MJPEG Frame Rate is 30 fps in NTSC and 25 fps in PAL.
The setting range for the H-264-1 Frame Rate is from 1 to 30 in NTSC and 1 to 25 in PAL.
The setting range for the H-264-2 Frame Rate is from 1 to 30 in NTSC and 1 to 25 in PAL.
Click Save to confirm the settings.
80
Configuration and Operation
Note:
It is suggested to set the Video Mask twice as large as the object it covers.
7.4.5 Video Mask
From the Mask screen, you may select up to five rectangular portions of the View Area to ‘Mask.’
Below is an illustration with the maximum five masks displayed in the View Area, the last (fifth) one
selected being highlighted in red.
Figure 76: Mask Screen
Active Mask Function
When a Video [Privacy] Mask is turned on, the area within the mask or box is blocked out or
obscured from view.
To enable a mask:
1. Check a Video Mask checkbox. A red frame is displayed in the Live Video pane on the right
side.
2. Use the mouse to drag and drop, adjust the mask’s size, and place it on the target zone.
To disable a mask:
Uncheck the checkbox of the Video Mask meant to be deleted. The selected mask
disappears from the Live Video pane.
Mask Setting
Mask color – The selections of Mask color include red, black, white, yellow, green, blue,
cyan, and magenta. Click Save to confirm the setting.
81
Quasar CF-3211/CF-4221 User and Installation Guide
Note:
Latitude does not support G.726 bit rates.
7.4.6 Audio
From the Audio screen you can select the Transmission Mode, Server Gain, Bit Rate, and enable or
disable storage of the audio recording.
Figure 77: Audio Screen
Transmission Mode
Full-duplex (Talk and listen simultaneously) – In the Full-duplex mode, the local and remote
sites can communicate with each other simultaneously, i.e. both sites can speak and be
heard at the same time.
Half-duplex (Talk or listen, not at the same time) – In the Half-duplex mode, the local or
remote site can only talk or listen to the other site at one time.
Simplex (Talk only) – In the Talk only Simplex mode, the local/remote site can only talk to the
other site.
Simplex (Listen only) – In the Listen only Simplex mode, the local/remote site can only listen
to the other site.
Disable – Select this option to turn off the audio transmission function.
Server Gain Setting
Set the audio input/output gain levels for sound amplification. The audio gain values are adjustable
(input from 1 to 10 and output from 1 to 6). The sound will be turned off if the audio gain is set to
Mute.
Bit Rate
Selectable audio transmission bit rate include 16 kbps (G.726), 24 kbps (G.726), 32 kbps (G.726), 40
kbps (G.726), µLAW (G.711) and ALAW (G.711). Both µLAW and ALAW signify 64 kbps, but in
different compression formats. A higher bit rate enables higher audio quality, but requires higher
bandwidth.
Click Save to confirm the settings.
82
Configuration and Operation
Note:
This function works only if the Recording to Storage option has been selected or if the
Schedule option has been set.
Exposure
White Balance
Picture Adjustment
Backlight
Digital Zoom
IR Function
WDR Function
Noise Reduction
TV System
Recording to Storage
This function enables recording of the audio on the SD card. The Recording to Storage function may
be enabled or disabled in the Audio screen. The default setting is Disabled.
Click Save to confirm the settings.
7.5 Camera-Related Settings
From the Camera tab, the administrator can adjust any of the camera settings, such as Exposure,
White Balance, Picture Adjustment, Backlight, Digital Zoom, IR Function, WDR Function, Noise
Reduction, and TV System.
Figure 78: Camera Settings Screen
Related Links:
83
Quasar CF-3211/CF-4221 User and Installation Guide
7.5.1 Exposure
The exposure is the amount of light received by the image sensor and is determined by the amount
of exposure by the sensor (shutter speed), and other exposure parameters.
Administrators may either allow the camera to automatically select an exposure level using a
programmed algorithm or choose the level themselves. Even in Auto Shutter, a Minimum Shutter
Speed may be set from the drop-down menu to ensure a maximum level of exposure. In Manual
Mode, the administrator can choose fixed shutter speeds from a drop-down menu. The smaller the
number (the higher the shutter speed) that the administrator selects, the lower the exposure level
and vice versa. Following is an illustration of the Camera menu.
Figure 79: Camera Settings Screen – Exposure
There are two exposure modes: Auto Mode and Manual Mode.
Auto Mode
There are three settings within Auto Mode:
Auto Iris Min Shutter Speed – When selecting this mode, the shutter is completely open and
the exposure priority is given to the iris. Shutter speed and AGC circuit function
automatically in cooperating with the iris to achieve a consistent exposure output.
84
Configuration and Operation
Auto Iris -
Min Shutter Speed
PAL
NTSC
1/25
1/30
1/12
1/15
1/6
1/8
1/3
1/4
1/1.5
1/2 1
Auto Shutter –
Min Shutter Speed
PAL
NTSC
1/425
1/500
1/300
1/350
1/215
1/250
1/150
1/180
1/120
1/120
1/100
1/100
1/75
1/90
1/50
1/60
1/25
1/30
1/12
1/15
1/6
1/8
1/3
1/4
1/1.5
1/2 1
Shutter Speed Priority
PAL
NTSC
1/425
1/500
1/300
1/350
1/215
1/250
1/150
1/180
1/120
1/120
1/100
1/100
1/75
1/90
1/50
1/60
1/25
1/30
The shutter speed range is from 1 to 1/30 sec (NTSC) and 1/1.5 to 1/25 sec (PAL). See the
able below showing all the options.
Auto Shutter Min Shutter Speed – When selecting this mode, the camera’s shutter speed
works automatically to achieve a consistent video output level. Users can select a suitable
shutter speed according to the environmental luminance.
The shutter speed range is from 1 to 1/500 sec (NTSC) and 1/1.5 to 1/425 sec (PAL). See
following table, which shows all the options.
Shutter Priority – When selecting this mode, a fixed exposure is set, while other parameters
can change. The shutter speed range is from 1 to 1/500 sec (NTSC) and 1/1.5 to 1/425 sec
(PAL). See table below showing all the options.
85
Quasar CF-3211/CF-4221 User and Installation Guide
Manual Mode -
Fixed Shutter Speeds
PAL
NTSC
1/10000
1/10000
1/3500
1/3000
1/2500
1/2000
1/1250
1/1000
1/600
1/725
1/425
1/500
1/300
1/350
1/215
1/250
1/150
1/180
1/120
1/120
1/100
1/100
1/75
1/90
1/50
1/60
1/25
1/30
1/12
1/15
1/6
1/8
1/3
1/4
1/1.5
1/2 1
Manual Mode (Fixed Shutter)
Manual Mode opens the iris completely with a fixed gain. Users can select a suitable shutter speed
according to the environmental luminance. The fixed shutter speed is selected from 1 to 1/10000 sec
(NTSC) and 1/1.5 to 1/10000 sec (PAL). You should select suitable shutter speed according to the
environmental luminance. See following table, which shows all the options.
Gain
A nominal video signal level is usually 1 volt peak-to-peak for composite video, 0.7 volts for
component or RGB video, or 0.3 volts for the chrominance subsection, at which level a fully
saturated picture is transmitted to the acceptor. However, for cases where the video signal is
attenuated, a low-noise, high-gain analog amplifier is built into quality video processing equipment.
This amplifier provides video gain control whereby the video signal can be boosted or reduced. Dark
pictures resulting from low level lighting are easily adjusted.
The Gain drop-down menu enables controlling the video gain from Off or in steps from 1 to 9.
86
Configuration and Operation
Light Sources
Color Temperature in K
Cloudy Sky
6,000 to 8,000
Noon Sun and Clear Sky
6,500
Household Lighting
2,500 to 3,000
75-watt Bulb
2,820
Candle Flame
1,200 to 1,500
7.5.2 White Balance
Shown below is the drop-down menu for controlling the camera’s White Balance (color balance).
Figure 80: Camera Settings Screen – White Balance
A camera needs to find a reference color temperature as a way of measuring the quality of a light
source for calculating all other colors. The unit for measuring this ratio is in Kelvin (K) degrees. You
can select one of the White Balance control modes according to the operating environment. The
table below shows the color temperature of some light sources for reference.
Three White Balance modes are available:
Auto – The Auto Balance White mode computes the white balance value output using color
information from the entire screen. It is suitable for an environment with a light source color
temperature in the range of approximately 2,700 ~ 7,500K.
ATW (Auto Tracking White Balance) – The Auto Tracking White Balance function
automatically adjusts the white balance in a scene while temperature color is changing. The
ATW Mode is suitable for an environment with a light source color temperature in the range
of approximately 2500 ~ 10,000K.
Manual – In this mode, you can manually change the white balance value. You can select a
number between 0 – 127 for either/both Rgain and Bgain to increase the red and/or blue
luminance.
Press <√> to confirm the new setting.
87
Quasar CF-3211/CF-4221 User and Installation Guide
7.5.3 Picture Adjustment
Adjustment of some qualities of the video is made possible by selecting Picture Adjustment in the
Camera tab. Brightness, Sharpness, Contrast, Saturation and Hue may all be adjusted via drop-down
menus from this window, as shown below.
Figure 81: Camera Settings Screen – Picture Adjustment
7.5.3.1 Brightness
You can adjust the image’s brightness by adjusting this parameter. Select from the range between 12 to +13. To increase video brightness, select a larger number. Press <√> to confirm the new
setting.
7.5.3.2 Sharpness
Increasing the sharpness level can make the image look sharper, especially enhancing the object’s
edge. Select from the range between 0 to +15. Press <√> to confirm the new setting.
7.5.3.3 Contrast
Camera image contrast level is adjustable: select from a range of -6 to +19. Press <√> to confirm the
new setting
7.5.3.4 Saturation
Camera image saturation level is adjustable: select from a range of -6 to +19. Press <√> to confirm
the new setting.
7.5.3.5 Hue
Camera image hue level is adjustable: select from a range of -12 to +13. Press <√> to confirm the
new setting.
88
Configuration and Operation
7.5.4 Backlight
The Backlight Compensation function prevents the center object from being too dark in
surroundings where excessive light is behind the center object. Select On or Off. Press <√> to
confirm the new setting.
Figure 82: Camera Settings Screen – Backlight
89
Loading...