INSTALLATION AND PROGRAMMING MAN
INSTALLATION AND PROGRAMMING MANUAL
Rev. 1.09
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/Quantum%20QR5.htm[5/6/2010 3:12:40 PM]
INSTALLATION AND PROGRAMMING MAN
INTRODUCTION AND WARRANTY
Pach & Co. thanks and congratulates you on the purchase of your Quantum QR5. The Quantum
QR5 is a residential and multi tenants telephone entry system.
The manual is designed to guide you through the detail in programming and use of the Quantum
QR5. It is important for you to read and follow the manual completely.
Pach & Co. new products are warranted to be free of defects in material or workmanship for a
period of
wholesale customers who buy direct from Pach & Co. or through Pach & Co.’s normal distribution
channels.
Pach & Co. does not warrant this product in any way to the end user consumer. Consumers must
obtain warranty information from the selling dealer and/or installer as to the nature of the dealer’s
warranty, if any. All contact to Pach & Co. from the end user consumer will be referred to the
consumer’s selling dealer and/or installer.
There are no obligations and/or liabilities on the part of Pach & Co. for consequential damages
arising out of or in connection with use or performance of Pach & Co. products or other indirect
damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or
reinstallation. Any use or change to Pach & Co. products not expressly approved by the
manufacturer, and performed by an authorized dealer/installer will immediately void the warranty.
All implied warranties, including warranties for marketability as well as implied warranties for
suitability, are valid only until the warranty expires or is voided, whichever comes first. Please visit
www.pach-co.com for the warranty in more detail.
two years, (24 months), from the date of purchase. This warranty extends only to
SPECIFICATION
Hardware
Input power 12VAC/DC-18VAC/DC (12 VAC 40VA supplied)
Current consumption 500-750 mA
Single Line Liquid Crystal Display
Built-in Radio Frequency Receiver
Built-in 26 Bit Wiegand Card Reader
12 Vdc camera power
Lock and keys
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/Quantum%20QR5.htm[5/6/2010 3:12:40 PM]
INSTALLATION AND PROGRAMMING MAN
Two on board relay
Two Auxiliary input
Operating environment 10ºF-140ºF
Relative Humidity 0%-95% non-condensing
Double 3/4" knock-out on the back and bottom panel
Dimension: 9-3/4"(L) x 6-3/8"(W) x 1-3/4"(D)
Features
100 access codes (4, 5, 6, 7, 8 digit) and 200 cards
10 temporary access codes valid 1-10 times
10 special access codes to hold open and close
10 programmable call forwarding phone number
Built-in 26 Bit Wiegand Card Reader and Radio Reader
Automatic call forwarding
Automatic card enrollment
Access code and card block programming
Two Auxiliary inputs
Two Door Sensors
600 event buffer (only available with TCP/IP Internet Explorer Browser programming)
Lighted keypad
INTRODUCTION TO QUANTUM QR5
Front View
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/Quantum%20QR5.htm[5/6/2010 3:12:40 PM]
INSTALLATION AND PROGRAMMING MAN
Back View
WIRING DIAGRAM
Click on the label for more detail diagram
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/Quantum%20QR5.htm[5/6/2010 3:12:40 PM]
INSTALLATION AND PROGRAMMING MAN
INPUT POWER - BATTERY BACKUP- CAMERA
Input Power:12-18 VAC/DC, 12VAC transformer is supplied
Type of wires 2-conductors 18 gauge stranded
Battery Backup: 12VDC 4Ahr
Type of wires 2-conductors 18 gauge stranded
Camera Power: 12 VDC on Board Power. Check the camera specification.
Type of wires 2-conductors 20 gauge stranded
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/Quantum%20QR5.htm[5/6/2010 3:12:40 PM]
INSTALLATION AND PROGRAMMING MAN
DOOR WIRING DIAGRAM
Two independent on board relay are available on the Quatum QR5, means you can control
two different doors independently. Each relay supports NO (normally open) and NC
(Normally Closed) contact. No power is supplied by the relays therefore you
separate power for door strike. Check the voltage requirements with door strike
manufacturer or refer to door strike owner's installation manual. DO NOT share power with
the Quantum QR5.
Relay rating: 250VAC/12A, 120VA/15A, 24VDC/15A. The relay supplies normally open (NO)
and normally closed (NC).
Wiring requirement: 18 gauge stranded
MUST supply
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/Quantum%20QR5.htm[5/6/2010 3:12:40 PM]
INSTALLATION AND PROGRAMMING MAN
TELEPHONE WIRING DIAGRAM
1. Using an existing telephone line.
Wiring requirements: 18 gauge stranded
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/Quantum%20QR5.htm[5/6/2010 3:12:40 PM]
INSTALLATION AND PROGRAMMING MAN
2. Using a DSL line.
Wiring requirements: 18 gauge stranded
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/Quantum%20QR5.htm[5/6/2010 3:12:40 PM]
INSTALLATION AND PROGRAMMING MAN
3. Using a Dedicated Phone Line
Wiring requirements: 18 gauge stranded
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/Quantum%20QR5.htm[5/6/2010 3:12:40 PM]
INSTALLATION AND PROGRAMMING MAN
4. As an Intercom
Wiring requirements: 18 gauge stranded
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/Quantum%20QR5.htm[5/6/2010 3:12:40 PM]
INSTALLATION AND PROGRAMMING MAN
AUXILIARY INPUT, DOOR SENSOR, RS- 485 AND WIEGAND DIAGRAM
Wiring requirements:
See manufacturers specification
RS- 485 requires 2- conductors category 5 or 2- conductors 18 gauge stranded
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/Quantum%20QR5.htm[5/6/2010 3:12:40 PM]
INSTALLATION AND PROGRAMMING MAN
The Quantum QR5 has built-in 26 bit Wiegand card reader, however if you need to use
different card reader, you may do so by disconnecting the existing card reader and replace
with your own 26-bit wiegand card reader as shown on the diagram.
Warning: Compatibility issue may occur.
FIRMWARE UPGRADE CONNECTOR
This connector is used to upgrade the firmware and only use by the manufacturer. Do not
attempt to upgrade the firmware, doing so will void the warranty.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/Quantum%20QR5.htm[5/6/2010 3:12:40 PM]
INSTALLATION AND PROGRAMMING MAN
MASTER CODE RETRIEVAL BUTTON
The default Master Code is 0000. If case the Master Code has been forgotten, you may
press and release the button to log on to programming, the screen will show as below
SPEAKER AND MICROPHONE
Speaker = 8.7 ohm
Microphone = 1.542 kOhm
RADIO RECEIVER
The Quantum QR5 has built-in Radio Frequency (RF) Receiver. The transmitter is not
included.
POWER SWITCH
The power switch must be in the OFF (left position) during the installation to avoid any
damages to the board. Check all the wiring, then turn the power switch ON (right position).
The system will initialize and the display will show scrolling message as shown partially
below
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/Quantum%20QR5.htm[5/6/2010 3:12:40 PM]
INSTALLATION AND PROGRAMMING MAN
EARTH GROUND
Wiring requirement: 16-18 gauge wire. Connect the earth ground wire into one of the door
hinge stud.
KEYPAD LAYOUT AND FUNCTIONALITY
The Quantum QR5 has built-in lighted keypad but no alphabetical lettering. Use the
template below for reference.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/Quantum%20QR5.htm[5/6/2010 3:12:40 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/Quantum%20QR5.htm[5/6/2010 3:12:40 PM]
INSTALLATION AND PROGRAMMING MAN
SYSTEM LOCAL PROGRAMMING
Log-on to programming
mode
16 Auto unlock schedule 33 Temporary Codes
00 Change master Code 17 Time zones 34 Unlock hold using codes
01 Call forwarding directory 18 Holiday time zones 35 Temporary cards
02 Edit existing directory 20 Aux-in 1
36 Unlock hold using card,
fob or transmitter
03 Delete directory 21 Aux-in 2 37 Initiating premise call
04 Delete all directories 22 Do not disturb 38 System answer mode
06 New access code 23 Lock out count
07 Delete access code 24 Alarm mode
08 Delete all access codes 25 Keypad press beep
39 Enable/disable remote
access
40 Remote access number
door1
41 Remote access number
door2
09 Access code digit 26 Door beep 42 Relay 2 mode
10 New card and transmitter
enrollment
27 Talk time 43 Do not disturb time zones
11 Delete card 28 Door 1 open time 45 Manual unlock timer
12 Delete all cards 29 Door 2 open time 46 Firmware Version
13 Set time
30. Enable or Disable Call
Forwarding
50 Erase memory to default
14 Set date 31 Call forwarding time 51 Edit welcome screen
15 Initializing event buffer
32 Automatic Call forwarding
directory
Log-on to programming mode
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
In case the master code is not available, refer to
Master code retrieval button, then click wiring
diagram link.
00 Change master code
It is recommended to replace the default password (0000) for security purposes. The master
code must be 4-digit.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
01 Call forwarding directory
10 call forwarding directories can be programmed in the system. The call forwarding can be
used to call direct or as an automatic call forwarding based on the programming on function
code: 32 Select call forwarding directory. The call forwarding will not work if the system is
installed as an intercom,
refer to the wiring diagram.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
02 Edit existing directory
In case of making mistake on
Function Code 01, then use this function code to make changes.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
03 Delete a directory
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
04 Delete all directories
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
06 New access code
A maximum of 100 access codes can be programmed in the system. The access code can be
set in 4, 5, 6, 7 and 8 digit, see
digit access code has been selected on
function code 09, default setting is 4-digit. For example, If 8
function code 09, then you MUST program 8-digit
code for everyone.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
07 Delete access code
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
08 Delete all access codes
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
09 Access code digit
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
The access code can be set to 4 (default setting), 5, 6, 7 or 8 digit thru the programming, once
the number of digit has been set, then all the access codes must have same number of digit.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
10 New card or transmitter enrollment
The Quantum QR5 has built-in 26 bit Wiegand Card Reader and Radio Receiver. A maximum of
100 combination of cards and transmitters can be programmed. Note: 26 bit wiegand access
card, fob and transmitter are optional and they are proprietary to Pach and Company.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
11 Delete card or transmitter
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
12 Delete all cards and transmitters
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
13 Set time
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
14 Set date
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
15 Initializing event buffer
The quantum QR5 has event recording tracking capability. You must use Internet Explorer
browser and optional TCP/IP box to use this feature. The event buffer must be initialized in
case of corruption or to start from fresh.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
16 Auto unlock schedules (AUS)
The Auto unlock schedules are used to open and close the door according to the time
schedules programmed in the system. A maximum 10 Auto unlock schedules can be
programmed in the system. For example: Schedule: 0, Open time: 0600, Close time:
1800, Day: 0 1 2 meaning the door will be opened at 06:00 AM and closed at 06:00 PM on
Sunday, Monday and Tuesday. This schedule will be repeated every week.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
17 Time Zones
The Quantum QR5 has 10 time zones.
Time Zone 00 is 24 hours access (not programmable)
Time zone 01-09 are programmable according to user specify.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
18 Holiday Time Zones
The quantum QR5 has
20 Holiday Time Zones. It is your responsibility to maintain the
holiday time zones since the holidays are not always fall on the same date every year. The
holiday time zones only link to the
auto unlock schedules.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
20 AUX IN 1
The Auxiliary Input 1 (AUXIN 1) can be use for exit switch, loop detector or any dry contact
input devices. The AUXIN 1 is associated with relay 1 (door 1).
See wiring diagram to wire the
AUXIN1
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
21 AUXIN 2
The Auxiliary Input 2 (AUXIN 2) can be use for exit switch, loop detector or any dry contact
input devices. The AUXIN 2 is associated with relay 2 (door 2).
See wiring diagram to wire the
AUXIN2
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
22 Do Not Disturb
Do Not Disturb will disable the call feature on the Quantum QR5 just incase if you do not want
to be disturb by the visitors. Time zone can also be set on Do not disturb, see function code
43.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
23 Lock Out Count
The Lock Out Count can be set 1-9. The system will be locked if invalid access (master code,
access code or card) has been entered according to the lock out count programmed.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
24 Alarm Mode
Alarm mode is associated with invalid access set on
function code 23. Alarm mode can be set
to DISABLE, LOCAL , CALLING the house intercom phone or calling the call forwarding
directory selected.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
25 Keypad Press Beep
The keypad press beep can be turned On (enable) and Off (disable).
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
26 Door Beep
The system will beep if granting access to door 1, door 2 or both doors. The beep can be
turned On and Off.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
27 Talk Time
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
The length of time for the two party to communicate using the system. The system will
disconnect the call if the talk time is expired. A minute before the talk time expired, the system
will beep. The tenant can extend the talk time by
pressing # on her his phone as soon as the
warning beep is heard.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
28 Door 1 Open Time
The length of time the door 1(relay 1) will open.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
29 Door 2 Open Time
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
The length of time the door 2(relay 2) will open.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
30 Enable or Disable Call Forwarding
This function must be enabled for automatic call forwarding
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
31 Call Forwarding Time
The system can be programmed for automatic call forwarding. The automatic call forwarding
only works if the system is installed as an intercom. The call forwarding time must be set
before the answering machine or voice mail answering the call, otherwise call forwarding time
will not be activated.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
32 Automatic Call Forwarding Directory
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
10 Call Forwarding Directory can be programmed in the system but only one can be selected
as automatic call forwarding directory.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
33 Temporary Codes
Up to 10 temporary codes can be programmed for limited number of used (01-10 times). The
code will be deleted after number of used expired.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
34 Unlock Hold Door Using Special Access Code
Door 1 and door 2 can be open and hold open and close using a special code. A valid code
must be entered to hold door 1, door 2 or both open and must be re-entered same code to
close door1, door 2 or both.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
35 Temporary Card or Transmitter
Up to 10 temporary cards or transmitters can be programmed for limited number of used (0110 times). The cards and transmitters will be deleted after number of used expired.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
36 Unlock Hold Using Card, Fob or Transmitter
Door 1 and door 2 can be open and hold open and close using card, fob or transmitter. A valid
code must be entered to hold door 1, door 2 or both open and must be re-entered same code
to close door1, door 2 or both.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
37 Initiating Premise Call
By default calling the Quantum QR5 from the premise phone (intercom Mode only),
must be pressed. The key may not work on certain area or phone service, therefore
must be used, below is the step.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
38 System Answer Mode
The Quantum QR5 will answer incoming call from an outside line. The system answer mode
must be enabled by selecting the number of ring. The number of rings can be set from 1st-9th
ring before the system answer. This feature can also set to disabled by selecting 0.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
39 Enable or Disable Remote Access
The tenant can press associated keypad key to release the door or gate. By default is number 9
key to release door 1 (relay 1) or 8 for door 2 (relay 2). This feature can be enabled or
disabled.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
40 DTMF Opening Door 1
By default DTMF number 9 key is used to open the door 1 remotely by the tenant. The DTMF
number
key can be changed.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
41 DTMF Opening Door 2
By default DTMF number 8 key is used to open the door 2 remotely by the tenant. The DTMF
number
key can be changed.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
42 Relay 2 Mode
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
Relay 2 is programmable. There are four mode:
1. Door Control (default)
2. Relay 2 triggers simultaneously as relay 1
3. Trigger if
Function Code 24 is activated
4. Turn Relay 2 ON (DTMF 6) and OFF (DTMF 7)
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
43 Do not Disturb Time Zones
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
It is to disable a call button ( ) according to the time zone programmed. No one can call
from the system. 10 Do Not Disturb Time Zones can be programmed in the system.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
45 Manual Unlock Timer
Using the timer door 1 and door 2 can be unlock according for an increment of one hour (0198 hours) or you can open and hold.
46 Firmware Version
Check firmware release date.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
50 Erase Memory to Default
This function code will erase the memory to factory default. All the programming cannot be
recovered unless if you program the system with optional TCP/IP Browser programming.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
51 Edit Welcome Screen
Welcome screen consists of 3-segment and each segment has 16 characters.
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
INSTALLATION AND PROGRAMMING MAN
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/system%20programming.htm[5/6/2010 3:12:44 PM]
MASTER CODE INFO
MASTER CODE RETRIEVAL
MASTER CODE RETRIEVAL BUTTON
The default Master Code is 0000. If case the Master Code is not available, you may press and
release the button to log on to programming, the screen will show as below
file:///C|/PACH%20&%20COMPANY/QUANTUM%20MANUAL%202009/Quantum%20QR5-1/master%20code%20info.htm[5/6/2010 3:12:56 PM]
Loading...