QUANTUM BATTERY 1+
OPERATING INSTRUCTIONS
For Quantum Battery 1+ 's with Serial Numbers : L270 and above
1.0 NEW FEATURES
Whether you are an old or new QB1 or QB1+ user, please read these new instructions for the latest
operating updates!
1.1 Battery Capacity Display - Without any flash Modules connected, press the ON/OFF Button. The
LED "gas gauge" will display battery capacity for 3 seconds and then shut off.
1.2 Discharge Prevention - If the ON/OFF Button is pressed for more than 10 seconds, the QB1+ shuts off
to prevent accidental discharge, such as when stored in a camera bag.
1.3 Energy Saving Mode - Hold down the ON/OFF Button about 3 seconds until the LED "gas gauge"
blinks once, then release the Button. The yellow LED will be on and the LED "gas gauge" will display
every 3 seconds.
1.4 Low Battery Shut Down - When the cells are exhausted QB1+ shuts itself off. The red Error LED
lights and one red "gas gauge" LED blinks slowly. After one minute all lights shut off. Charge QB1+ as
soon as possible.
1.5 Over Current/Overheat Protection - QB1+ shuts down, the red Error LED will light, and the "gas
gauge" will blink 3 times every 2 seconds.
1.6 Charging - Charging time is decreased to between 3 and 5 hours. The LED "gas gauge" indicates the
charge progress.
1.7 Self Check - When connecting the charger, QB1+ goes through a self check. If QB1+ detects any
problems, the red Error LED will light, and one or more of the "gas gauge" LED's will be blinking. See
section 5.3.
2.0 CHARGING QB1+
2.1 When to Charge:
Charge QB1+ before using it for the first time.
Charge after each use. The QB1+'s lead cells have no memory.
Never discharge fully prior to recharging.
Charge immediately if there is a Low Battery shutdown.
Charge before storing QB1+. Recharge a stored QB1+ every 3 months.
2.2 How to Charge:
Remove Modules from output jacks.
Connect the charger to QB1 + and mains (household) power.
Charge to completion in one continuous period. Do not use a timer or connect to a mains outlet that
can be turned off.
Do not use a voltage adapter. This will damage QB1+. Instead, use one of the optional QB1+ chargers
listed on our web site.
Charge until all green LED indicators are on.
3.0 FUEL GAUGE INDICATORS
The LED "fuel gauge" indicates the remaining capacity of the battery during charging or discharging.
WARNING: LOW BATTERY
ONLY THE RED LIGHT IS ON
RECHARGE
LOW------------FULL
FULL POWER
ALL LIGHTS ON
4.0 POWERING YOUR FLASH WITH QUANTUM BATTERY 1+
4.1 Follow this sequence to assure proper connection to your flash!
a. Connect the Module to the flash. The Module Instructions explain the proper Module position.
b. Plug the Module cord into power output l or 2 on the QB1+.
c. Turn on the flash's power switch.
d.
Press the ON/OFF Button of the QB1 +. You must immediately hear the flash charge, or see indicators
on the flash unit turn on.
e. If you see or hear nothing press the ON/OFF Button on QB1+ to turn it off!
f. If you failed to power your flash, reposition the Module inside its battery compartment. Repeat steps a-e
until the flash responds and the correct position has been determined.
4.2 Powering two flashes at once:
Connect two modules into outputs 1 and 2. The combined ISO 100 guide number may not exceed 240 (ft.)
or 72 (meters). This is the equivalent of two shoe mount flashes.
5.0 TROUBLESHOOTING
5.1 Flash not powered:
Is the Module correct for your flash?
Is the Module positioned correctly and firmly seated inside the battery compartment?
Is the Module cord securely plugged into the QB1+ output?
Is the flash switched ON?
Has the QB1+ been charged?
5.2 Charger not charging:
Is the charger plugged into a working mains outlet?
Is the charger securely plugged into the charge jack of the QB1+?
Is the charge LED indicator on?
5.3 Gas Gauge LED's are blinking after connecting the charger:
If there are three LED's blinking simultaneously, and the red Error LED is on, make sure the proper
charger is plugged into the QB1+.
If one, two, or four LED's blink and the red Error LED is on, this indicates the QB1+ detects a fault in
its circuit. Please return the unit for service.
5.4 Overload Occurs:
An overload is indicated by the red Error LED and a blinking gas gauge. QB1+ power to the
Modules will automatically shut down. To restart the QB1+, determine the cause of the overload and
remove it. Then turn QB1+ off and on again.
5.5 Causes of Overload:
A Module inserted incorrectly into a flash battery compartment.
A short circuit across the Module contacts. Be sure the contacts do not touch any metal surface.
A defective flash unit which has an internal short circuit (repair or replace flash).
Firing a flash repeatedly before the ready light comes on. This will over stress the flash and may also
result in under exposure.
6.0 CARE AND MAINTENANCE
6.1 Battery Replacement:
All rechargeable cells have a limited lifetime, usually a few hundred recharges. The recharge life is greater for
shallow discharges, and also depends upon proper charging. Battery cells can be replaced by sending the
QB1+ and charger to Quantum Instruments or any overseas distributor.
6.2 Maximum Consecutive Flashes:
Do not exceed the flash manufacturer's recommendation for the maximum number of full power consecutive
flashes, without a cool-off period!
6.3 Conserve Power:
Use the Energy Saving mode, section 1.3. To save more power in a slow shooting session, turn QB1+ off
when it is not being used.
6.4 Environment:
Recharge indoors at room temperature.
Store at room temperature or cooler. Recharge every 3 months when in storage.
Operation temperature: -40°F to 120°F (-40°C to 55°C).
Never submerge the QB1+ or its charger in water.
CONTAINS SEALED LEAD ACID BATTERY.
MUST BE RECYCLED OR DISPOSED OF PROPERLY.
DO NOT PLACE USED BATTERIES IN YOUR REGULAR TRASH!
Return this battery to a federal or state approved sealed lead battery recycler.
This may be where you purchased the battery.
Loading...