Quantum P1000PAK User Manual

Document 6221100-02, Ver. 2, Rel. 0
ATL P1000 Series Library
March 1999
Unpacking Instructions
Introduction....................................................................................................3
Selecting an Installation Location ...................................................... .........5
Floor Clearance .......................................................................................6
Floor Strength and Inclination........ ......................................................6
Overhead Clearance...............................................................................6
Power and Grounding ...........................................................................6
Power Inlet .................................................... ......... ...........................7
Rack Current Rating Consideration ..............................................7
Grounding.........................................................................................7
0
Temperature......................................................................................7
Environmental Requirements...............................................................7
Unpacking the Library................................................................ ......... .........8
Unloading Space Requirements............ ......................................................9
Uncrating the Library .................................................................................10
Installing the Slide Assembly in the Rack................................................13
Verifying the Rack Requirements.......................................................13
Rack Current Rating Consideration ............................................13
Grounding.......................................................................................14
Temperature....................................................................................14
Determining the Mounting Position..................................................14
Installing the Slide Assembly in the Rack.........................................15
1
ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 2, Rel. 0 March 1999
Adjusting the Slide Assembly ............................................................ 17
Adjusting the Slide Assembly on the Mounting Brackets....... 17
Adjusting the Slide Assembly Tray on the Slide Rails.............19
Removing the Library from the Pallet.....................................................22
Removing a Stand-alone Library from the Pallet............................22
Removing a Rack-mount Library from the Pallet ...........................24
Removing the Internal Packing Materials...............................................28
Opening the Doors...............................................................................28
Removing the Load and Bulk Packs ..................................................28
Removing the Shipping Restraint......................................................29
Packaging the Library for Reshipment....................................................31
2
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999
Figure 1 ATL P1000 Series Library , Stand-alone Configuration

Introduction

The ATL P1000 Series is an automated tape l ibrary co nsisting of up to 4 tape drives and 30 DLT™ cartridges.
This document explains how to unpack the A TL P1000 Series. Once the library is unpacked and moved to the desired installation location, set up the library using the instructions in the ATL P1000 Series Library User’s Guide.
The P1000 library is shipped in either a stand-alone (see figure 1) or rack-mount configuration (see figure 2). The stand-alone P1000 is set on casters. The rack-mount P1000 comes with a s lide tray ass embl y for installation in a rack.
Note: A rack is not provided with the rack- mount P10 00; it mus t be obtained
separately.
Window
0
Key lock
Touch screen
graphical user
interface (GUI)
Bulk pack door
Load pack door
Power switch
Load port
Introduction 3
ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 2, Rel. 0 March 1999
Figure 2 ATL P1000 Series Library , Rack-mount Configuration
Rack (not included)
Key lock
Bulk pack door
GUI
Load pack door
Power switch
Load port
4 Introduction
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999

Floor Space

Figure 3 Floor Space Requirements, Stand­alone Library

Selecting an Installation Location

2
When selecting an installation site for the ATL P1000 Series, consider the following requirements:
floor space floor clearance floor strength and inclination power and grounding environmental conditions
These requirements are also described in the ATL P1000 Series Library User’s Guide.
2
Figure 3 shows the floor space requirements of the stand-alone P1000.
17.5 in. (45 cm)
24 in. (61 cm)
29.5 in. (75 cm)
Library FrontBack
54 in. (137.2 cm)
Selecting an Installation Locat ion 5
ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 2, Rel. 0 March 1999
Figure 4 shows the floor space requirements for the rack-mount P1000.
Figure 4 Floor Space Requirements, Rack-mount Library
24 in. (61 cm)
24 in.
(61 cm)
each side
Front
17.5 in. (45 cm)

Floor Clearance

Floor Strength and Inclination

Library
Back
4
The stand-alone P1000 has a floor clearance of 0.75 in. (1.9 cm). Place
19-inch rack
(extended from rack)
30 in. (76.2 cm)
24 in.
(61 cm)
the library on a level, uncarpeted floor free of defects.
The floor at the installation site must be rated at 250 lb/ft2 (1221 kg/
4
2
m
). This is sufficient to support a fully loaded P1000 on the floor or in
a rack. The floor at the installation site must be level to within 0.25 in (6.4 mm)
over a 6 ft by 6 ft (1.8 m by 1.8 m) area.

Overhead Clearance

4
To remove the P1000 enc losure, there must be a minimum clearance of 24 in. (61 cm) above the library. When combined with the height of the library (21 in./53 cm), this is a total of 45 in. (114.5 cm) from the floor (stand-alone library) or bottom of the slide (rack-mount library).

Power and Grounding

4
The library auto-ranging power supply accepts single-phase, 90 VAC to 264 VAC input power at 47 Hz to 63 Hz.
6 Selecting an Installation Location
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999
Figure 5 AC Power Receptacle

Power Inlet

The power inlet is an IEC-320 connector (see figure 5). For international applications, replace the power cord with a harmonized 3x1.0 mm

Rack Current Rating Consideration

2
power cord approved by the country where used.
Ground
~100V to 120V / ~200V to 240V 6A/3A 50Hz/60Hz IEC-320 Type
NeutralLine
Consider the current rating of the rack before instal ling more than one P1000 library. The P1000 library is rated 6A/3A (120V/230V). This means that no more than two libraries can be installed in a typical 15A/120V rack.
If other equipment is installed in the rack, determine the total current rating of all the equipment before adding the P1000 library to the rack.
4
5

Environmental Requirements

Grounding

5
The P1000 must be connected to a grounded power outlet. If the library is rack-mounted, the rack must also be grounded.

T e mperature

5
The rack temperature should be less than 90qF (32qC).
The installation site (stand-alone library) or the interior of the rack
5
(rack-mount library) must meet the following environmental requirements:
humidity: 20% to 80%, non-condensing temperature: 59qF to 90qF (15qC to 32qC) altitude: sea level to 10,000 feet (3,033 meters)
Selecting an Installation Locat ion 7
ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 2, Rel. 0 March 1999

Unpacking the Library

The P1000 unpacking procedure consists of the following steps: receiving the library from the shipper (see “Unloading Space
Requirements” on page 9)
uncrating the library (see “Uncrating the Library” on page 10) installing the slide assembly in the rack (rack-mount library only)
(see “Installing the Slide Assembly in the Rack” on page 13)
removing the library from the pallet (see “Removing the Library
from the Pallet” on page 22)
removing the internal packing materials from the library (see
“Removing the Internal Packing Materials” on page 28)
The following sections detail each of these steps.
Note: Before performing the procedures in the following sections, ma ke sure
the site you have chosen for the installation meets the requirements listed in “Selecting an Installation Location” on page 5.
5
8 Unpacking the Library
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999
Figure 6 Unloading Space Requirements, Stand­alone Library

Unloading Space Requirements

Before uncrating the library, verify that you have sufficient space. For the stand-alone unit, allow a minimum of six feet in front of the ramp side of the pallet (see figure 6).
Note: Unpack the library as close to the installation site as possible.
Library
Pallet
5
Unloading area
(minimum)
18 in. (46 cm)
Pallet ramp
30 in. (76 cm)
33 in. (84 cm)
97 in. (2.5 m)
Unloading Space Requirements 9
ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 2, Rel. 0 March 1999

Uncrating the Library

To uncrate the P1000 library:
Procedure
1
Open the top of the shipping carton by carefully cutting the packaging tape.
The following items are stacked on top of the P1000:
accessories tray ramp (stand-alone library) or slide assembly (rack-mount
library)
2
Remove these items from the carton and set them aside.
3
Remove all foam supports from inside the carton (see figure 7 on page 11 and figure 8 on page 12).
6
10 Uncrating the Library
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999
Figure 7 Uncrating the Stand-alone Library
Accessories tray
Ramp
Foam supports
Library
Clips
Uncrating the Library 11
ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 2, Rel. 0 March 1999
Figure 8 Uncr ating the Rack-mount Library
Accessories tray
Slide assembly
Foam supports
Library
Clips
Procedure (continued)
4
Release the four clips that secure the carton to the pallet. To release a clip, pinch the center tabs of the clip firmly together
and pull on the tabs.
5
Lift the carton off of the pallet and set it aside.
6
Compare the contents of the shipping carton and the accessories tray with the packing list included in the shipping carton.
If any items are missing or damaged, contact your authorized reseller.
12 Uncrating the Library
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999

Installing the Slide Assembly in the Rack

If you are installing a rack-mount library, install the slide assembly in the rack before proceeding to “Removing the Library from the Pallet” on page 22.
This procedure consists of the following steps:
verifying that the rack meets the necessary requirements determining the mounting position of the slide assembly within
the rack
mounting the slide assembly in the rack adjusting the slide assembly to allow for required clearances
Warning: Use safe lifting practices when moving the slide assembly
or the library. Th e slide assembly weighs about 25 lbs (1 1.25 kg) and its size and construction mak e it awkwar d to handle. The library weighs 89 lbs (40 kg); it must be lifted with assistance. Failure to follow these guidelines may result in equipment damage or personal injury.
8

Verifying the Rack Requirements

Warning: When installing the library and other devices in the rack,
determine the weight of each device and position the heaviest devices lower in the rack. If the library is the first device to be installed, place it near the bottom of the rack.
Before installing the slide assembly in the rack, verify that the rack
8
meets the following requirements.

Rack Current Rating Consideration

8
Consider the current rating of the rack before instal ling more than one P1000 library. The P1000 library is rated 6A/3A (120V/230V). This means that no more than two libraries can be installed in a typical 15A/120V rack.
If other equipment is installed in the rack, determine the total current rating of all the equipment before adding the P1000 library to the rack.
Installing the Slide Assembly in the Rack 13
ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 2, Rel. 0 March 1999

Determining the Mounting Position

Figure 9 Positioning the Slide Assembly

Grounding

8
The P1000 must be connected to a grounded power outlet. If the library is rack-mounted, the rack must also be grounded.

T e mperature

8
The rack temperature should be less than 90qF (32qC).
To determine the mounting position of the slide assembly within the
8
rack:
Procedure
1
Locate the desired mounting position for the library (see figure 9). The library and slide assembly require at least 21 in. (54 cm or 12
rack units) of vertical clearance. To ensure stability, mount the library low in the rack.
0.5 in. (12.7 mm)
0.625 in. (16 mm)
0.625 in. (16 mm)
0.5 in. (12.7 mm)
Mounting bracket
Slide assembly Locking bracket
Insert temporary support screw here
As indicated in figure 9, the bottom edge of each slide assembly bracket must line up with the end of a rack unit.
1 rack unit (1.75 in. / 4.45 cm)
Rack retma rail
0.5 in. (12.7 mm)
0.625 in. (16 mm) 1 rack unit
21 in. (54 cm
or 12 rack units)
minimum vertical
clearance required
14 Installing the Slide Assembly in the Rack
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999
Procedure (continued)
2
If the rack retma rail holes are not threaded, attach the appropriate threaded clips to the holes that correspond to:
the mounting bracket tabs (front and back) the locking bracket tabs (front only) the temporary support screws (front and back)
3
Insert a temporary support screw into each retma rail, just below the desired position of the slide assembly bracket.
Use four of the 10-32 x 3/4 in. slide mounting screws as temporary support screws.
4
Make sure the support screws are level with one another. Leave the screws extended out of the retma rails at least 0.625 in.
(16 mm) so they will support the slide assembly mounting brackets during installation.

Installing the Slide Assembly in the Rack

To install the slide assembly in the rack (see figure 10 on page 16):
9
Procedure
1
Loosen (but do not remove) the nuts holding the rear mounting brackets to the slide assembly.
2
Measure the depth of the rack, from the outside edge of the front retma rail to the outside edge of the rear retma rail.
3
Adjust the rear mounting brackets so that the distance from the front mounting brackets to the rear mounting brackets is slightly greater than the depth of the rack.
4
Insert the slide assembly into the rack:
a
Lift the slide assembly and tilt it sideways.
b
Insert the back end of the slide assembly into the front of the rack, keeping the slide assembly above the temporary support screws.
c
When the rear brackets clear the rear retma rails, turn the slide assembly right side up.
d
Place the slide assembly in the rack so that each bracket rests on a temporary support screw.
5
Secure the front mounting brackets to the front retma rails, using four 10-32 x 3/4 in. screws from the accessories kit.
6
Adjust the rear mounting brackets so they are flush with the outside of the rear retma rails.
Installing the Slide Assembly in the Rack 15
ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 2, Rel. 0 March 1999
Procedure (continued)
7
Remove the two 10-32 x 3/4 in. temporary support screws from the front retma rails and install them in the left and right rear mounting brackets to secure the rear mounting bra ckets to the rack retma rails.
8
Remove the two 10-32 x 3/4 in. temporary support screws from the rear retma rails and use them to finish securing the rear mounting brackets to the rack retma rails.
Note: Do not tighten the nuts securing the rear mounting brackets to
the slide assembly. You will tighten these during the following procedure, “Adjusting the Slide Assembly.”
9
Remove the four temporary support screws.
Figure 10 Installing the Slide Assembly in the Rack
Retma rai l s
Mounting screws
Support screw
16 Installing the Slide Assembly in the Rack
Mounting screws
Support screw
Rear mounting bracket
Slide assembly
Front mounting bracket
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999

Adjusting the Slide Assembly

Figure 11 Loosening the Outer Nuts
Now that the slide assembly is installed in the rack, verify that:
10
The front door of the rack opens and closes freely. The rear door of the rack opens and closes freely. When fully extended, the slide assembly extends at least 30 in.
(76.2 cm) from the front of the rack.
If the slide assembly and rack do not meet the above requirements, complete the procedures in this section to adjust the slide assembly. The number of adjustments required varies from rack to rack.

Adjusting the Slide Assembly on the Mounting Brackets

10
To adjust the slide assembly on the mounting brackets:
Procedure
1
Loosen the outer nuts on both sides of the slide assembly (see figure 1 1).
These nuts secure the mounting brackets to the slide rails.
Outer nuts
Outer nuts
2
Move the slide assembly forward or backward as necessary.
Installing the Slide Assembly in the Rack 17
ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 2, Rel. 0 March 1999
Procedure (continued)
3
When the slide assembly is in the desir ed position, tighten all outer nuts:
a
Pull the slide assembly tray forward until you can access the four rea r sc rews.
b
Tighten each of the four rear nuts by holding the nut with an 11/32 inch open-ended wrench and then tightening its corresponding screw with a Phillips screwdriver.
c
Extend the slide assembly out of the rack until both the intermediate and inner channels of the slide rails lock (see figure 12).
The intermediate channels are secured by the intermediate channel locks, which are located on the inner, back edge of the intermediate channels.
d
Release the intermediate channel locks by rotating them upward slightly.
Note: Do not release the inner channel locks.
e
Push the slide assembly back into the rack until the acces s hol e on the inside of the intermediate channel exposes a screw.
f
Use a Phillips screwdriver to tighten the screw while holding its corresponding nut with an 11/32 inch open-ended wrench.
g
Repeat steps 3e and 3f to tighten the remaining front nuts.
h
Press on the inner channel locks to release them. The inner channel locks are located on the outer, back edge of
the inner channels.
i
Push the slide assembly tray back into the rack.
4
Check for clearance. If necessary, repeat this procedure to adjust the slide assembly further.
18 Installing the Slide Assembly in the Rack
Figure 12 Slide Assembly Tray, Fully Extended
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999
Intermediate channel lock
Access hole
Intermediate channel
Inner channel lock
Inner channel

Adjusting the Slide Assembly Tray on the Slide Rails

To adjust the slide assembly tray on the slide rails:
Procedure
1
Loosen the inner nuts on both sides of the slide assembly (see figure 13).
Access these nuts from underneath the slide assembly tray.
12
2
Move the slide assembly tray forward or backward as necessary.
Installing the Slide Assembly in the Rack 19
ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 2, Rel. 0 March 1999
Figure 13 Loosening the Inner Nuts
Inner nuts
Inner nuts
Procedure (continued)
3
When the slide assembly tray is in the desired position, tighten all inner nuts:
a
Extend the slide assembly out of the rack until both the intermediate and inner channels of the slide rails lock (see figure 12).
This allows you to access the front screws.
b
Tighten each of the front nuts by holding the nut with an 11/32 inch open-ended wrench and then tightening its corresponding screw with a Phillips screwdriver.
c
Press on the inner channel locks to release them (see figure 12).
d
Push the slide assembly back into the rack until the acces s hol e on the outside of the inner channel exposes a screw.
20 Installing the Slide Assembly in the Rack
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999
Procedure (continued)
e
Use a Phillips screwdriver to tighten the screw while holding its corresponding nut with an 11/32 inch open-ended wrench.
f
Repeat steps 3d and 3e to tighten the remaining inner nuts.
g
Push the slide assembly tray back into the rack.
4
Check for adequate clearance. If necessary, repeat this procedure to adjust the slide tray further.
Now that the slide assembly is properly installed and adjusted, you are r eady to r emove the P 1000 fr om the shippi ng pallet a nd mount it in the rack.
Installing the Slide Assembly in the Rack 21
ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 2, Rel. 0 March 1999
Removing a Stand-alone Library from the Pallet

Removing the Library from the Pallet

13
This section provides separate procedures for the stand-alone and rack-mount libraries:
To remove a stand-alone library from the pallet, see the following
section, “Removing a Stand-alone Library from the Pallet.”
To remove a rack-mount library from the pallet, see “Removing a
Rack-mount Library from the Pallet” on page 24.
Warning: Two people should perform steps that involve lifting or
guiding the library. Use safe practices when lifting or guiding the library and handling the slide assembly or the ramp.
To remove a stand-alone library from the pallet:
13
Procedure
1
Remove the plastic bag enclosing the P1000:
a
Cut along the front seam of the plastic bag.
b
Continue to cut all the way to the back of the library.
c
Fold the bag out of the way.
2
Remove the foam supports from between the li brary and the pallet (see figure 14).
22 Removing th e Library from the Pallet
Figure 14 Removing the Foam Supports, Stand-alone Library
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999
Foam supports
Figure 15 Removing the Stand-alone Library from the Pallet
Procedure (continued)
3
Attach the ramp to the pallet using fastener strips (see figure 15).
4
Make any necessary preparations for moving the library. This may involve clearing a path to the installation site, unlocking
doors, and placing mats over carpeted areas.
5
Carefully roll the library down the ramp.
Fastener strips
6
Detach the ramp and place it on top of the pallet.
Removing the Library from the Pallet 23
ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 2, Rel. 0 March 1999
Procedure (continued)
7
Roll the library to the installation site.
8
Save the shipping carton, bag, foam supports, ramp, and pallet for future use.
These items are required to package the library for reshipment.
Removing a Rack-mount Library from the Pallet
To remove a rack-mount library from the pallet:
15
Note: The instructions in this section assume you have already installed the
slide assembly in the rack. If you have not, do so now, following the instructions in “Installing the Slide Assembly in the Rack” on page 13.
Procedure
1
Remove the plastic bag enclosing the library:
a
Cut along the front seam of the plastic bag.
b
Continue to cut all the way to the back of the library.
c
Fold the bag out of the way.
2
Pull the slide tray forward in the rack so it is fully extended.
Warning: The rack may ti p forward when you extend the slide tray or
place the library on the slide tray. If rack stabilizing feet are present, extend them during this procedure. If the rack does not have stabilizing feet, use extreme caution when extending the slide tray and mounting the P1000 in the rack.
24 Removing th e Library from the Pallet
Figure 16 Lifting the Rack-mount Library from the Pallet
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999
Procedure (continued)
3
W ith the help of a second person, lift the library fr om the pallet (see figure 16).
Library
Shipping bag
Pallet
Foam supports
Removing the Library from the Pallet 25
ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 2, Rel. 0 March 1999
Procedure (continued)
4
Place the library on the fully extended slide assembly tray (see figure 17).
Figure 17 Placing the Library on the Slide Assembly Tray
Inner channel lock
Screws
5
Secure the library to the slide tray, using six screws from the accessories kit (see figure 17).
6
Verify that, when the slide assembly is fully extended, there is adequate clearance around the library to access the back panel and remove the library enclosure.
7
Press on the inner channel loc ks t o release them (see figure 17) and then push the slide assembly all the way into the rack.
26 Removing th e Library from the Pallet
Figure 18 Locking the Slide Tray in the Rack
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
Procedure (continued)
8
To prevent the library from sliding out of the rack during operation, secure the locking brackets to the retma rails (see figure 18).
March 1999
Retma rail
Locking bracket
9
These items are required to package the library for reshipment.
Removing the Library from the Pallet 27
ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 2, Rel. 0 March 1999
Removing the Internal Packing

Opening the Doors

Materials
18
This section explains how to remove the internal packing materials that protect the library during shipping and installation.
Caution: Before removing the internal packing materials, verify that
the library is at its final installation site. Moving the library without these materials in place may damage the library.
Caution: Take precautions to prevent electrostatic discharge
whenever you remove the library enclosure or open the library doors.
18
To open the library doors:
Procedure

Removing the Load and Bulk Packs

1
Locate the key in the accessories kit and unlock the front door of the library.
2
Open the left door first, then open the right door.
To remove the load and bulk packs (see figure 19):
18
Procedure
1
Grip the load pack handles and squeeze them together. This releases the latches securing the load pack.
2
Still holding the load pack handles, pull the load pack forwar d and out of the library.
3
Repeat steps 1 and 2 to remove the bulk pack.

28 Removing the Internal Packing Materials

Figure 19 Removing the Load and Bulk Packs
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999
Handles

Removing the Shipping Restraint

To remove the shipping restraint:
19
Note: The shipping restraint that protects the extension axis assembly is
attached to the bottom drive shelf and fits over the supports for the load and bulk packs.
Procedure
1
Grasp the front edge of the shipping restraint and carefully push inward at both corners while lifting i t up at an angle ( see figur e 20).
The tab on the shipping restraint (between the mounting blocks for the load and bulk packs) pops up, releasing the shipping restraint from the load pack shelf. The back of the shipping restraint unhooks from the bottom drive shelf.
2
Lift the shipping restraint off the extension axis assembly.
3
Raise the extension axis assembly and remove the foam block beneath it.
4
Lower the extension axis assembly to its normal position on the floor of the library.
Note: Retain the original shipping con tainer and shipping bag, pall et,
ramp, accessories tray, and all packing materials for future use.
Removing the Internal Packing Materials 29
ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 2, Rel. 0 March 1999
Figure 20 Removing the Shipping Restraint
Extension axis assembly
Shipping restraint
Drive shelf
30 Removing the Internal Packing Materials
ATL P1000 Series Library Unpacking Instructions
Document 6221100-02, Ver. 2, Rel. 0
March 1999

Packaging the Library for Reshipment

If it becomes necessary to reshi p the library, repackage the library in its original shipping materials as follows:
Procedure
1
Unload and eject all tape cartridges from the tape drives.
2
Turn off the library and disconnect all cables.
3
Open the library doors:
a
Using the key in the accessories ki t, unlock the fr ont door of the library .
b
Open the left door first, then open the right door.
4
Remove the load and bulk packs (see figure 19 on page 29):
a
Grip the load pack handles and squeeze them together. This releases the latches securing the load pack.
b
Still holding the load pack handles, pull the load pack forward and out of the library.
20
c
Repeat steps 4a and 4b to remove the bulk pack.
Note: In order to install the shipping restraint, the gripper must face
the front of the library.
5
If the gripper is facing the tape drives, rotate the extension axis so that the gripper faces the front of the library:
a
Reaching through the library doors, move the gripper backwards (away from t he tape drives) and compress it against its rear limit.
This unlocks the rotary assembly and permits the extension axis to rotate.
b
Rotate the extension axis assembly 180° so that the gripper faces the front of the library.
c
Jiggle the extension assembly slightly to relatch the rotary assembly.
6
Secure the extension axis assembly:
a
Center the extension axis assembly between the mounting blocks for the load and bulk packs.
b
Raise the extension axis assembly and place the foam block beneath it.
Packaging the Library for Reshipment 31
ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 2, Rel. 0 March 1999
Procedure (continued)
c
Carefully lower the extension axis assembly so that it rests on the foam block.
d
Hook the lip of the shipping restraint under the edge of the bottom drive shelf (see figure 20 on page 30).
e
Move the gripper forward or backward as necessary so that it fits underneath the shipping restraint.
f
Press the front edge of the shipping restraint downward until the tab on the shipping restraint snaps into place.
7
Replace the load and bulk packs.
8
Close and lock the library doors.
9
Recrate the library:
a
Place the library in the shipping bag.
b
Place the library on the shipping pallet.
c
Replace the foam supports between the library and the pallet (see figure 14 on page 23).
d
Place the shipping carton over the library and secure it with the four clips.
e
Replace the foam supports inside the shipping carton.
f
Place the ramp (stand-alone library) or slide assembly (rack­mount library) on top of the library (see figure 7 on page 11 and figure 8 on page 12).
g
Place the accessories tray on top of the ramp or slide assembly.
h
Close and seal the shipping carton.
The library is now ready for reshipment.
32 Packaging the Library for Reshipment
Loading...