MODEL LHQM
EXIT/UNIT COMBINATION
IMPORTANT SAFEGUARDS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS MAY RESULT IN DEATH, SERIOUS INJURY
OR SIGNIFICANT PROPERTY DAMAGE – For your protection, read and follow these warnings and instructions carefully before
installing or maintaining this equipment. These instructions do not attempt to cover all installation and maintenance situations. If you do
not understand these instructions or additional information is required, contact Lithonia Lighting or your local Lithonia Lighting distributor.
WARNING: RISK OF ELECTRIC SHOCK – NEVER CONNECT TO, DISCONNECT FROM OR SERVICE WHILE EQUIPMENT IS
ENERGIZED.
WARNING: RISK OF FIRE – Lamps are hot. Keep combustibles material away from hot parts. Observe lamp manufacturer’s
warnings, recommendations and restrictions on lamp operation and maintenance. Make sure lamps are correctly installed.
WARNING: DO NOT USE ABRASIVE MATERIALS, OR OTHER SOLVENTS. USE OF THESE SUBSTANCES MAY DAMAGE
FIXTURE, WHICH MAY RESULT IN PERSONAL INJURY.
WARNING: RISK OF PERSONAL INJURY – This product may have sharp edges. Wear gloves to prevent cuts or abrasions when
removing from carton, handling, installing and maintaining this product. (WHERE APPLICABLE)
• Before wiring to power supply, turn off electricity at fuse or circuit breaker.
• Disconnect A.C. power and unplug battery before servicing.
• Consult your local building code for approved wiring and installation.
• Do not use outdoors.
• Do not let power supply cord touch hot surfaces.
• Do not mount near gas or electric heater.
• Do not install a damaged fixture.
• This product must be installed in accordance with the applicable installation codes and ordinances.
• Proper grounding is required to ensure personal safety. (WHERE APPLICABLE)
• All service shall be performed by qualified service personnel. This product must be installed and maintained in accordance with the
applicable installation codes by a person familiar with the construction and operation of the product and the hazards involved.
• Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel.
• The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
• Do not use this equipment for other than intended use.
• Halogen cycle lamps operate at high temperatures. Do not store or place flammable materials near lamp.
• Use caution when servicing batteries. Battery acid can cause burns to skin and eyes. If acid is spilled on skin or eyes, flush acid with fresh
water and contact a physician immediately.
CAUTION: Halogen cycle lamp(s) may be used in this fixture. To avoid shattering, do not operate lamp in excess of rated voltage.
Protect lamp against abrasions and scratches and against liquids when lamp is operating. Dispose of lamps with care. Halogen lamps operate
at high temperatures. Do not store or place flammable materials near lamps.
SAVE THESE INSTRUCTIONS
US Patent No. 5,526,251; 5,646,502; 6,142,648; D379,373; 5,611,163; D484,272; D473,672
Canadian Patent No. 80,141 & 2,180,495
GENERAL INFORMA TION
SHOWN WITH LEAD ACID BATTERY
A
E
To Remove Face Plate-
Press in snaps at bottom or top of housing to separate
face plate from housing.
B
To Remove Back Plate-
Press in snaps at bottom or top of housing. Then
release latches A and B from the inside of housing.
C
To Remove Directional chevrons-
Remove colored panel and push chevron out for
desired configuration.
F
To Remove Canopy-
Rotate cam locking pin level with housing and remove
from hooks. Squeeze snaps and pull housing free.
G
DC Connection-
Connect battery to lamp board
AFTER AC power can be continuously provided to exit.
D
Remove and Relocate Lamp Mount Assembly
Remove face plate and back plate.
Disconnect lamp harness from lamp board.
Press four snaps (two each side) to release lamp
mount assembly from housing. Relocate to top of
housing and resnap into place. Connect lamp harness
to lamp board.
Page 2
To Remove Lens and Change Lamps-
Release lens bylifting outward and over button with
thumb. Replace lamp with an identical lamp.
Loading...