quantum HARDCARD EL DATASHEET

Page 1
HardCard EL
Though they will work under Windows 95, they do so in `DOS Compatibility mode'. No enhanced mode driver exists at
ATA Jumper Settings
Product Name: Hardcard IIXL Serial Number Codes: CDC and CDE Formatted Capacity: 52 XL 52,311,040 105XL 105,231,360 Average Access Time: 17ms Interface: ST506; BIOS driven as IDE Driver Needed: ATDOSXL.SYS
Must be installed in CONFIG.SYS as:
DEVICE=ATDOSXL.SYS
In order for the hardcard to work in a given system, the user must assign a unique IRQ and a BIOS address. The default for this card is IRQ 11, BIOS address C8000-C9FFF. SW8 is reserved. Due to a bus timing issue, the hardcards are unable to work in most Pentium and DX4 systems.
this time, and there are no plans to produce one.
IRQ
1 of 1
Page 2
HardCard EL
DRIVE SELECT
ATA Jumper Settings
IRQ
11 12 14
*These are default settings
ADDRESS SELECTION
SW5
ON* OFF OFF
SW6
OFF* ON OFF
SW1
ON*
ON ON ON ON ON ON ON
*These are default settings.
SW2
ON*
ON ON
ON OFF OFF OFF OFF
SW7 SW8
OFF* OFF* OFF ON
SW3
ON*
ON OFF OFF
ON
ON OFF OFF
OFF OFF
SW4
ON*
OFF
ON
OFF
ON
OFF
ON
OFF
BIOS ADDRESS
C8000-C9FFF* 170-177, 376-377
CA000-CBFFF 320-327, 32E-32F
CC000-CDFFF 170-177, 376-377
CE000-CFFFF 320-327, 32E-32F D0000-D1FFF 170-177, 376-377 D2000-D3FFF 320-327, 32E-32F D4000-D5FFF 170-177, 376-377 D6000-D7FFF 320-327, 32E-32F
I/O ADDRESS
0 0 1 1 0 0 1 1
2 of 2
Page 3
HardCard EZ
Though they will work under Windows 95, they do so in `DOS Compatibility mode'. No enhanced mode driver exists at this
ATA Jumper Settings
Product Name: Hardcard IIEZ Serial Number Codes: GDF, GDG, GDH and GDJ Formatted Capacity: HC EZ42 42MB HC EZ85 85MB HC EZ127 127MB HC EZ170 170MB HC EZ240 240MB Average Access Time: From 19ms to 16ms. Interface: ST506; BIOS driven as IDE Driver Needed: ATDOSHC.SYS
Must be installed in CONFIG.SYS as: DEVICE=ATDOSHC.SYS In order for the hardcard to work in a given system, the user must assign a unique IRQ and a BIOS address. The default for this card is IRQ 11, BIOS address C8000-C9FFF. SW8 is reserved for IRQ 14 (IDE MODE). Due to a bus timing issue, the hardcards are unable to work in most Pentium and DX4 systems.
time and there are no plans to produce one.
1 of 1
Page 4
DRIVE SELECT
IRQ
IRQ
10 11 12 14
*These are default settings
ADDRESS SELECTION
SW5 SW6 SW7 SW8
ON OFF* ON* OFF OFF OFF OFF
OFF
OFF OFF OFF* OFF* ON OFF ON
SW1
ON*
ON ON ON ON ON ON ON
*These are default settings.
SW2
ON*
ON ON
ON OFF OFF OFF OFF
OFF
SW3
ON*
ON OFF OFF
ON
ON OFF OFF
HardCard EZ
ATA Jumper Settings
SW4
ON*
OFF
ON
OFF
ON
OFF
ON
OFF
BIOS ADDRESS
C8000-C9FFF* 170-177, 376-377
CA000-CBFFF
CC000-CDFFF
CE000-CFFFF D0000-D1FFF D2000-D3FFF D4000-D5FFF D6000-D7FFF
I/O ADDRESS
320-327, 32E-32F
170-177, 376-377
320-327, 32E-32F
170-177, 376-377
320-327, 32E-32F
170-177, 376-377
320-327, 32E-32F
0 0 1 1 0 0 1 1
2 of 2
Page 5
HardCard II
In order for the hardcard to work in a given system, the user must assign a unique IRQ and a BIOS address.
. No enhanced mode driver
ATA Jumper Settings
Product Name: Hardcard II Serial Number Codes: CDA and CDB Formatted Capacity: HCII-40 40,256,000 HCII-80 80,512,000 Average Access Time: 25ms Interface: ST506; BIOS driven as IDE Driver Needed: ATDOSHC2.SYS
Must be installed in CONFIG.SYS as: DEVICE=ATDOSHC2.SYS
The default for this card is IRQ 11, BIOS address C8000-C9FFF. SW8 is reserved. Due to a bus timing issue, the hardcards are unable to work in most Pentium and DX4 systems. Though they will work under Windows 95, they do so in `DOS Compatibility mode'
exists at this time, and there are no plans to produce one.
IRQ
1 of 1
Page 6
HardCard II
DRIVE SELECT
ATA Jumper Settings
IRQ
IRQ 11 ON* OFF* IRQ 12 OFF ON
*These are default settings.
ADDRESS SELECTION
SW4 SW5
SW1
ON*
ON ON
ON OFF OFF OFF OFF
*These are default settings.
SW2
ON*
ON OFF OFF
ON
ON OFF OFF
SW3
ON*
OFF
ON
OFF
ON
OFF
ON
OFF
BIOS ADDRESS
C8000-C9FFF* 170,177, 376-377*
CA000-CBFFF 320-327, 32E-32F
CC000-CDFFF 170-177, 376-377
CE000-CFFFF 320-327, 32E-32F D0000-D1FFF 170-177, 376-377 D2000-D3FFF 320-327, 32E-32F D4000-D5FFF 170-177, 376-377 D6000-D7FFF 320-327, 32E-32F
I/O ADDRESS
0*
0 1 1 0 0 1 1
2 of 2
Loading...