Quantum DXi6802 and
DXi690x: Rack Mount Rails
Replacement
Follow the steps in this document to replace the rack mount rails in the DXi6802
or DXi690x:
1 Shutting Down the System on page 2
2 Replacing the rack mount rails:
• Replacing the DXi6802 or DXi690x Node Rails on page 3:
• Replacing the DXi6802 Array or Expansion Module Rails on page 8
• Replacing the DXi690x Array or Expansion Module Rails on page 12
3 Turning On the System on page 17
Necessary Tools
Before you begin, gather the necessary tools:
• Small flat head screwdriver
• Large flat head screwdriver
• #2 PHILLIPS screwdriver
Caution: Use appropriate ESD precautions, including the use of a grounding
strap, when performing any of these procedures.
© 2015 Quantum Corporation. All rights reserved. Quantum, the Quantum logo, DLT, DLTtape, the DLTtape logo, SuperLoader,
Scalar, DXi, StorageCare, StorNext, GoProtect, and Vision are registered trademarks of Quantum Corporation and its affiliates
in the United States and/or other countries. All other trademarks are the property of their respective owners. Quantum
specifications are subject to change.
6-68446-01, April 2016
*6-68446-01*
Quantum DXi6802 and DXi690x: Rack Mount Rails Replacement
Port 1 Port 2
ID/Diag
Lnk Lnk
Power switches
Array Module (rear view)
ID/Diag
Port 1
Power switches
Expansion Module (rear view)
6-68446-01
April 2016
Shutting Down the System
To shut down the system:
Caution: Before shutting down the DXi6802 or DXi690x, make sure that all
backup and replication jobs are finished, and that space
reclamation activity is complete.
1 Shut down the system from the remote management console using the
Shutdown option on the Utilities > Reboot & Shutdown page.
Note: Shutting down the system can take up to 15 minutes. Only the
Node will completely shut down.
Figure 1 Turning Off the Array
Modules (RBODs)
Figure 2 Turning Off the
Expansion Modules (EBODs)
Note: If you need help accessing remote management, see the
User’s Guide
DXi690x User’s Guide
(6-67199) at www.quantum.com/DXi6800docs or the
(6-68159) at www.quantum.com/
DXi6000
DXi6900docs.
2 After the Node shuts down, turn off both power switches on the back of
each Array Module (RBOD) (see
Figure 1). Wait until the seven segment
display on the rear of the module turns off.
3 Turn off both power switches on the back of each Expansion Module (EBOD)
(see
Figure 2).
2 Shutting Down the System
Quantum DXi6802 and DXi690x: Rack Mount Rails Replacement
Replacing the DXi6802 or DXi690x Node Rails
Follow the steps below to replace the DXi6802 or DXi690x Node rails:
1 Removing the DXi6802 or DXi690x Node from the Rack on page 3
2 Installing the DXi6802 or DXi690x Node Rack Mounting Rails on page 5
3 Installing the DXi6802 or DXi690x Node on page 6
6-68446-01
April 2016
Removing the DXi6802 or DXi690x Node from the Rack
To remove the DXi6802 or DXi690x Node from the rack:
1 Shut down the DXi6802 or DXi690x system (see Shutting Down the System
on page 2).
2 If installed, remove the front bezel from the Node by lifting the latch on the
left side of the bezel.
3 Remove all power, SAS, Ethernet, and Fibre Channel cables from the rear of
the Node. Make sure to label the cables so they can be easily identified
when they are re-connected to the Node after the replacement procedure is
complete.
4 Press the locking tab on either side of the Node, and slide the Node out
from the rack until the inner rails lock.
Note: If necessary, remove the optional screws securing the Node to the
front of the rack (behind the locking tab).
5 Locate the lock levers on the sides of the inner rails (see Figure 3). Unlock
each lever by rotating it up to its release position.
Replacing the DXi6802 or DXi690x Node Rails 3
Quantum DXi6802 and DXi690x: Rack Mount Rails Replacement
Inner slide rails
Rear rail standoffs
Rear rail J-slots
Slide-release lock button
Lock lever
Locking tab
Locking tab
6-68446-01
April 2016
Figure 3 Removing the Node
from the Rack
6 Slide the Node forward until the rail standoffs are at the front of the J-slots.
7 Remove the Node from the rack and place it on a level surface.
WARNING: The DXi6802 Node (including hard drives) weighs 53.3
pounds (24.2 kg). The DXi6900 G1/G2 Node (including hard
drives) weighs 53.0 pounds (24.0 kg). A minimum of two
people are required to lift the chassis.
8 Use a flat head screwdriver to lift the latch release button on the end piece
midpoint and unseat each rail (see
the rack.
4 Replacing the DXi6802 or DXi690x Node Rails
Figure 4), and then remove the rails from
Figure 4 Removing the Node
Latch release button
Rails
Quantum DXi6802 and DXi690x: Rack Mount Rails Replacement
6-68446-01
April 2016
Installing the DXi6802 or DXi690x Node Rack Mounting Rails
To install the replacement DXi6802 or DXi690x Node rack mounting rails:
1 If present, remove the orange plastic clip from each mounting rail so that
the rail can be extended. (The rails are marked right and left.)
2 Position the left and right rail end pieces labeled FRONT facing inward, and
orient each end piece to seat in the holes on the front side of the vertical
rack flanges (see
Figure 5).
Replacing the DXi6802 or DXi690x Node Rails 5
Quantum DXi6802 and DXi690x: Rack Mount Rails Replacement
Rail front end
Rail back end
Latches click into place in rack flange
(round or square holes)
Latch release button
6-68446-01
April 2016
Figure 5 Installing the Node
Rails
Installing the DXi6802 or DXi690x Node
3 Align each back end piece in the bottom and top holes of the desired U
spaces.
4 Engage the back end of the rail until it fully seats on the vertical rack flange
and the latch clicks into place. Repeat these actions to position and seat the
front end piece on the vertical rack flange.
To install the DXi6802 or DXi690x Node:
1 Pull the inner slide rails out of the rack until they lock into place (see
Figure 6).
6 Replacing the DXi6802 or DXi690x Node Rails
Figure 6 Installing the Node
Inner slide rails
Rear rail standoffs
Rear rail J-slots
Slide-release lock button
Lock lever
Locking tab
Locking tab
Quantum DXi6802 and DXi690x: Rack Mount Rails Replacement
6-68446-01
April 2016
2 Locate the rear rail standoff on each side of the system and lower them into
the rear J-slots on the slide assemblies.
3 Rotate the system downward until all the rail standoffs are seated in all four
of the J-slots.
4 Slide the system inward until the lock levers click into place.
5 Press the slide-release lock buttons on both rails and slide the system into
the rack.
6 Reconnect all power, SAS, Ethernet, and Fibre Channel cables on the rear of
the Node.
Note: For cabling diagrams, see the
Configuration Guide
DXi6800docs or the
(6-67757) at www.quantum.com/
DXi690x Installation and Configuration Guide
DXi6800 Installation and
(6-68160) at www.quantum.com/DXi6900docs.
7 Turn on the system (Turning On the System on page 17).
8 If applicable, replace the front bezel. Insert the right side of the bezel into
the slots on the right side of the Node, then snap the left side of the bezel
into place.
Replacing the DXi6802 or DXi690x Node Rails 7
Quantum DXi6802 and DXi690x: Rack Mount Rails Replacement
End cap tabs
Expansion Module
End cap tabs
Array Module
6-68446-01
April 2016
Replacing the DXi6802 Array or Expansion Module Rails
Follow the steps below to replace the DXi6802 Array or Expansion Module rails:
1 Removing the DXi6802 Array or Expansion Module from the Rack on page 8
2 Installing the DXi6802 Array or Expansion Module Rack Mounting Rails on
page 9
3 Installing the DXi6802 Array or Expansion Module on page 11
Removing the DXi6802 Array or Expansion Module from the Rack
Figure 7 Removing the Array
or Expansion Module
1 Shut down the DXi6802 system (see Shutting Down the System on page 2).
2 Remove all power and SAS cables from the rear of the Array or Expansion
Module. Make sure to label the cables so they can be easily identified when
they are re-connected to the module after the replacement procedure is
complete.
3 Remove the end caps from each side of the Array or Expansion Module (see
Figure 7).
4 Remove the bottom front screw on each rail (see Figure 8).
8 Replacing the DXi6802 Array or Expansion Module Rails
Figure 8 Removing the Array
Rack mounting holes Adjustment screws
Mounting rail
Remove the bottom front
screw BEFORE sliding out
the module
or Expansion Module Rails
Quantum DXi6802 and DXi690x: Rack Mount Rails Replacement
6-68446-01
April 2016
5 Slide the Array or Expansion Module out of the rack and place it on a level
surface.
WARNING: The DXi6802 Array Module (RBOD) and Expansion Module
(EBOD) weigh 55.6 pounds (25.2 kg) and 54.7 pounds (24.8
kg) respectively. A minimum of two people are required to lift
either chassis.
6 For each rail, perform the following steps (see Figure 12):
a Loosen the adjustment screws on the mounting rail.
b Remove the screws securing the rear flange of the mounting rail to the
cabinet.
c Remove the top front screw on each rail.
d Contract the support rail and remove rail from the cabinet.
Installing the DXi6802 Array or Expansion Module Rack Mounting Rails
To install the replacement DXi6802 Array Module or Expansion Module rack
mounting rails:
Note: The rails are designed to accommodate racks with both round and
square holes. Nut clips are
not
needed for racks with square holes.
Replacing the DXi6802 Array or Expansion Module Rails 9
1 For racks with square holes, replace the set of small spacers on the front and
rear of the support rail with the large spacers included in the rail kit (see
Figure 9).
Note: You do
not
need to replace the spacers if you are using a rack with
round holes.
Quantum DXi6802 and DXi690x: Rack Mount Rails Replacement
Rack mounting holes Adjustment screws
Mounting rail
Spacers
Insert the bottom front
screw AFTER installing the
module to secure the
module in place
6-68446-01
April 2016
2 Make sure that the adjustment screws on the support rail are loose.
3 Place the support rail inside the cabinet and extend the support rail until the
flanges on the support rail touch the inside of the cabinet.
4 Insert one M5 screw through the front of the cabinet and screw into the top
captured nut in the support rail. Add a large washer between each M5
screw and the mounting rail bracket.
Note: Only insert the top screw on the front of the rail at this time. Do
not
insert the bottom screw yet.
5 Insert two M5 screws through the rear of the cabinet and screw into the
captured nuts in the rear flange in the mounting rail. Add a large washer
between each M5 screw and the mounting rail bracket.
6 Tighten the adjustment screws on the mounting rail.
Caution: Do not over tighten the screws. You can strip the threads on
the mounting rails if the hex screws are over-tightened.
7 Repeat this procedure for the second mounting rail.
Figure 9 Installing the Array or
Expansion Module Rails
10 Replacing the DXi6802 Array or Expansion Module Rails
Quantum DXi6802 and DXi690x: Rack Mount Rails Replacement
End caps (indicator icons)
Expansion Module
End cap (drive numbers)
Array Module
6-68446-01
April 2016
Installing the DXi6802 Array or Expansion Module
Figure 10 Installing the Array
or Expansion Module
To install the DXi6802 Array Module or Expansion Module:
1 Align the Array or Expansion Module with the rails and slide the module into
the rack (see
Figure 10).
2 Insert one M5 screw through the bottom hole in the front of each rail to
secure the module in place (see
Figure 9).
3 Install the end caps on either side of the module by inserting the top of the
end cap first and then snapping the bottom into place.
Install the end cap with the indicator icons to the left of the module, and
install the end cap with the drive numbers to the right of the module.
4 Reconnect all power and SAS cables on the rear of the module.
Note: For cabling diagrams, see the
Configuration Guide
(6-67757) at
DXi6800 Installation and
www.quantum.com/DXi6800docs.
5 Turn on the system (Turning On the System on page 17).
Replacing the DXi6802 Array or Expansion Module Rails 11
Quantum DXi6802 and DXi690x: Rack Mount Rails Replacement
6-68446-01
April 2016
Replacing the DXi690x Array or Expansion Module Rails
Note: NetApp Co-Branded EMEA installations do not follow the rack
installation procedures below. NetApp Co-Branded EMEA Array and
Expansion Module rails follow the same procedures as the DXi6802
disk backup system (see
Module Rails on page 8).
Follow the steps below to replace the DXi690x Array or Expansion Module rails:
1 Removing the DXi690x Array or Expansion Module from the Rack on
page 12
2 Installing the DXi690x Array or Expansion Module Rack Mounting Rails on
page 15
3 Installing the DXi690x Array or Expansion Module on page 16
Replacing the DXi6802 Array or Expansion
Removing the DXi690x Array or Expansion Module from the Rack
To remove the DXi690x Array or Expansion Module from the rack:
1 Shut down the DXi690x system (see Shutting Down the System on page 2).
2 Remove all power and SAS cables from the rear of the Array or Expansion
Module. Make sure to label the cables so they can be easily identified when
they are re-connected to the module after the replacement procedure is
complete.
3 Remove the end caps from each side of the Array or Expansion Module.
4 Remove the 10-32 x 3/4 in. SEM screw with washer on each side of the Array
or Expansion Module’s front panel (see
Figure 11).
12 Replacing the DXi690x Array or Expansion Module Rails
Figure 11 Removing the Array
Front of Array or
Expansion Module
10-32 x 3/4 in. screw
Rails
or Expansion Module
Quantum DXi6802 and DXi690x: Rack Mount Rails Replacement
6-68446-01
April 2016
5 Slide the Array or Expansion Module out of the rack and place it on a level
surface.
WARNING: The DXi690x Array Module and Expansion Module (including
hard drives) weigh 59.0 pounds (26.8 kg) and 57.0 pounds
(25.9 kg) respectively. A minimum of two people are required
to lift the chassis.
6 For each rail, pull on the blue release latch on each end piece and unseat the
rail from the rack (see
Figure 12).
Replacing the DXi690x Array or Expansion Module Rails 13
Quantum DXi6802 and DXi690x: Rack Mount Rails Replacement
Rail front end
Rail back end
Latches click into place in rack flange
(round or square holes)
Latch release button
6-68446-01
April 2016
Figure 12 Removing the Array
or Expansion Module Rails
14 Replacing the DXi690x Array or Expansion Module Rails
Quantum DXi6802 and DXi690x: Rack Mount Rails Replacement
Rail front end
Rail back end
Latches click into place in rack flange
(round or square holes)
Latch release button
6-68446-01
April 2016
Installing the DXi690x Array or Expansion Module Rack Mounting Rails
Figure 13 Installing the Array
or Expansion Module Rails
To install the replacement DXi690x Array Module or Expansion Module rack
mounting rails:
1 Position the left and right rail end pieces labeled FRONT facing inward, and
orient each end piece to seat in the holes on the front side of the vertical
rack flanges (see
Figure 13).
2 Align each back end piece in the bottom and top holes of the desired U
spaces.
3 Engage the back end of the rail until it fully seats on the vertical rack flange
and the latch clicks into place. Repeat these actions to position and seat the
front end piece on the vertical rack flange.
Replacing the DXi690x Array or Expansion Module Rails 15
Quantum DXi6802 and DXi690x: Rack Mount Rails Replacement
Front of Array or
Expansion Module
10-32 x 3/4 in. screw
and nylon washer
Rails
6-68446-01
April 2016
Installing the DXi690x Array or Expansion Module
Figure 14 Array or Expansion
Module Installation
To install the Array Module or Expansion Module:
1 Align the Array or Expansion Module with the rails and slide the module into
the rack (see
Figure 14).
16 Replacing the DXi690x Array or Expansion Module Rails
2 Use a 10-32 x 3/4 in. SEM screw with washer at the bottom hole on each
side of the Array or Expansion Module’s front panel to secure the module to
the rack.
3 Install the end caps on either side of the module by inserting the top of the
end cap first and then snapping the bottom into place.
Install the end cap with the indicator icons to the left of the module, and
install the end cap with the drive numbers to the right of the module.
4 Reconnect all power and SAS cables on the rear of the module.
Note: For cabling diagrams, see the
Configuration Guide
(6-68160) at www.quantum.com/
DXi690x Installation and
DXi6900docs.
5 Turn on the system (Turning On the System on page 17).
Turning On the System
ID/Diag
Port 1
Power switches
Expansion Module (rear view)
Port 1 Port 2
ID/Diag
Lnk Lnk
Power switches
Array Module (rear view)
Power button
Node (front view)
To turn on the DXi6802 or DXi690x system:
1 Turn on both power switches on the back of each Expansion Module (EBOD)
(see
Figure 15). Wait until the seven segment display on the rear of the
module displays 00 (approximately 1 minute).
Figure 15 Turning On the
Expansion Modules (EBODs)
2 Turn on both power switches on the back of each Array Module (RBOD) (see
Figure 16). Wait until the seven segment display on the rear of the module
displays 99 (approximately 3 minutes).
Quantum DXi6802 and DXi690x: Rack Mount Rails Replacement
6-68446-01
April 2016
Figure 16 Turning On the
Array Modules (RBODs)
Figure 17 Turning on the Node
3 Press the power button on the front of the Node (see Figure 17). Wait for
the system to boot before attempting to log on.
Note: The system can take approximately 30 minutes to start up,
depending on the amount of installed storage capacity.
Turning On the System 17
Quantum DXi6802 and DXi690x: Rack Mount Rails Replacement
6-68446-01
April 2016
18 Turning On the System
Loading...