Quantum AS 30.0, AS 10.2, AS 20.5, AS 40.0, AS 60.0 Product Manual

Quantum Fireball Plus AS

Quantum Fireball Plus ASQuantum Fireball Plus AS

Quantum Fireball Plus AS

10.2/20.5/30.0/40.0/60.0 GB AT

10.2/20.5/30.0/40.0/60.0 GB AT10.2/20.5/30.0/40.0/60.0 GB AT

10.2/20.5/30.0/40.0/60.0 GB AT
Product Manual

Product ManualProduct Manual

Product Manual

December 12, 2000

81-121729-04

Quantum res e rv e s the right to mak e c ha n ges and improvements to its prod u c t s, wi t h ou t i n cu r ri n g
any obligation to incorporate such changes or improvements into units previously sold or shipped.

You can request Quantum publications from your Quantum Sales Representative or order them
directly from Quantum.

Publication Number: 81-121729-04

UL/CSA/TUV/CE

UL standard 1950 recognition granted under File No. E78016
CSA standard C22.2 No. 950 certification granted under File No. LR49896
TUV Rheinland EN 60 950 granted under File No. R 9677196
Tested to FCC Rules for Radiated and Conducted Emissions, Part 15, Sub Part J, for Class-B

Equipment.

SERVICE CENTERS

Quantum Service Center Quantum Asia-Pacific Pte. Ltd. Quantum Customer Service Group
160 E. Tasman 50 Tagore Lane #b1-04 Quantum Ireland Ltd.
San Jose, California 95134 Singapore, 2678 Finnabair Industrial Park
Phone: [phone] Phone: [phone] Dundalk
Fax: [phone] Fax: [phone] County Louth, Ireland
http://www.quantum.com Tel: [phone]

Fax: [phone]

PATENTS

These products are covered by or licensed under one or more of the following U.S. Pa tents:
4,419,701; 4, 538,193 4,625,109; 4,639,798; 4,647,769; 4,647,997; 4,661,696; 4,669,004;
4,675,652; 4,703,176; 4,730,321; 4,772,974; 4,783,705; 4,819,153; 4,882,671; 4,920,442;
4,920,434; 4,982,296; 5,005,089; 5,027,241; 5,031,061; 5,084,791; 5,119,254; 5,160,865;
5,170,229; 5,177,771; O ther U.S. and F oreign Patents Pending.

©

2000 Quantum Corporation. All rights reserved. Printed in U.S.A.

Quantum, the Quantum logo, and AIRLOCK are trademarks of Quantum Corporation, registered
in the U.S.A. and other countries. Capacity for the extraordinary, Quantum Fireball Plus AS,
AutoTransfer, AutoRead, Au toWrite, DisCache, DiskWa re, Defect Fr ee Interfac e, and WriteC ache
are trademarks of Quantum Corporation. All other brand names or trademarks are the property of
their manufacture rs.

This product or document is protected by copyright and distributed under licenses restricting its
use, copying, distribution, and decompilation. No part of this product or document may be
reproduced in any form by any means without prior written authorization of Quantum and its
licensors, if any.

RESTRICTED RIGHTS LEGEND: Use, duplication, or disclosure by the government is subject to
restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer
Software clause at DFARS 252.227-7013 and FAR 52.227-19.

THIS PUBLICATION IS PROVIDED “AS IS’ WITHOUT WARRANTY OF ANY KIN D, EITHER
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON­INFRINGEMENT.

Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT iii

Table of Contents

Table of ContentsTable of Contents

Table of Contents

Chapter 1
ABOUT THIS MANUAL

1.1 AUDIENCE................................................................................................................. 1-1

1.2 MANUAL ORGANIZATION..................................................................................... 1-1

1.3 TERMINOLOGY AND CONVENTIONS ................................................................. 1-1

1.4 REFERENCES............................................................................................................. 1-3

Chapter 2
GENERAL DESCRIPTION

2.5 PRODUCT OVERVIEW ............................................................................................. 2-5

2.6 KEY FEATURES......................................................................................................... 2-5

2.7 Regulatory Compliance Standards.............................................................................. 2-7

2.8 HARDWARE REQUIREMENTS................................................................................ 2-7

Chapter 3
INSTALLATION

3.1 SPACE REQUIREMENTS.......................................................................................... 3-1

3.2 UNPACKING INSTRUCTIONS ................................................................................ 3-2

3.3 HARDWARE OPTIONS............................................................................................. 3-4

3.3.1 Cable Select (CS) Jumper .................................................................................. 3-5

3.3.2 Drive Select (DS) Jumper .................................................................................. 3-6

3.3.3 Master Jumper configuration ............................................................................. 3-6

3.3.4 Jumper Parking (PK) Position ........................................................................... 3-6

3.3.5 Alternate Capacity (AC) .................................................................................... 3-7

3.4 ATA BUS ADAPTER.................................................................................................. 3-8

3.4.1 40-Pin ATA Bus Connector ............................................................................... 3-8

3.4.2 Adapter Board .................................................................................................... 3-8

3.5 MOUNTING ............................................................................................................... 3-9

3.5.1 Orientation ......................................................................................................... 3-9

3.5.2 Clearance .......................................................................................................... 3-11

3.5.3 Ventilation ........................................................................................................ 3-11

3.6 COMBINATION CONNECTOR (J1) ...................................................................... 3-11

3.6.1 DC Power (J1, Section A) ................................................................................ 3-12

3.6.2 External Drive Activity LED ............................................................................ 3-12

3.6.3 ATA Bus Interface Connector (J1, Section C) ................................................ 3-12

3.7 FOR SYSTEMS WITH A MOTHERBOARD ATA ADAPTER............................... 3-13

3.8 FOR SYSTEMS WITH AN ATA ADAPTER BOARD............................................. 3-13

3.8.1 Adapter Board Installation ............................................................................... 3-13

3.9 TECHNIQUES IN DRIVE CONFIGURATION ...................................................... 3-15

3.9.1 The 528-Megabytes Barrier .............................................................................. 3-15

Table of Contents

iv Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT

3.9.2 The 8.4-Gigabytes Barrier .................................................................................3-16

3.9.3 Operating system limitations ............................................................................3-16

3.10 SYSTEM STARTUP AND OPERATION................................................................. 3-17

Chapter 4
SPECIFICATIONS

4.1 SPECIFICATION SUMMARY ................................................................................... 4-1

4.2 FORMATTED CAPACITY.......................................................................................... 4-3

4.3 DATA TRANSFER RATES......................................................................................... 4-3

4.4 TIMING SPECIFICATIONS ...................................................................................... 4-4

4.5 POWER........................................................................................................................ 4-5

4.5.1 Power Sequencing ..............................................................................................4-5

4.5.2 Power Reset Limits .............................................................................................4-5

4.5.3 Power Requirements ...........................................................................................4-6

4.6 ACOUSTICS................................................................................................................ 4-7

4.7 MECHANICAL ........................................................................................................... 4-8

4.8 ENVIRONMENTAL CONDITIONS.......................................................................... 4-8

4.9 SHOCK AND VIBRATION........................................................................................ 4-9

4.10 HANDLING the DRIVE ........................................................................................... 4-10

4.11 RELIABILITY............................................................................................................ 4-10

4.12 ELECTROMAGNETIC SUSCEPTIBILITY.............................................................. 4-11

4.13 SPINDLE IMBALANCE........................................................................................... 4-11

4.14 DISK ERRORS.......................................................................................................... 4-11

Chapter 5
BASIC PRINCIPLES OF OPERATION

5.1 Quantum Fireball Plus AS DRIVE MECHANISM..................................................... 5-1

5.1.1 Base Casting Assembly .......................................................................................5-3

5.1.2 DC Motor Assembly ...........................................................................................5-3

5.1.3 Disk Stack Assemblies ........................................................................................5-3

5.1.4 Headstack Assembly ...........................................................................................5-4

5.1.5 Rotary Positioner Assembly ................................................................................5-4

5.1.6 Automatic Actuator Lock ...................................................................................5-4

5.1.7 Air Filtration .......................................................................................................5-5

5.2 DRIVE ELECTRONICS.............................................................................................. 5-5

5.2.1 Integrated µProcessor, Disk Controller and ATA Interface Electronics ............5-6

5.2.2 Read/Write ASIC ................................................................................................5-8

5.2.3 PreAmplifier and Write Driver .........................................................................5-10

5.3 FIRMWARE FEATURES .......................................................................................... 5-10

5.3.1 Disk Caching .....................................................................................................5-10

5.3.2 Head and Cylinder Skewing .............................................................................5-12

5.3.3 Error Detection and Correction ........................................................................5-13

5.3.4 Defect Management ..........................................................................................5-15

Table of Contents

Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT v

Chapter 6
ATA BUS INTERFACE AND ATA COMMANDS 6-1

6.1 INTRODUCTION....................................................................................................... 6-1

6.2 SOFTWARE INTERFACE.......................................................................................... 6-1

6.3 MECHANICAL DESCRIPTION................................................................................ 6-1

6.3.1 Drive Cable and Connector ................................................................................ 6-1

6.4 ELECTRICAL INTERFACE ....................................................................................... 6-1

6.4.1 ATA Bus Interface .............................................................................................. 6-1

6.4.2 Host Interface Timing ........................................................................................ 6-9

6.5 REGISTER ADDRESS DECODING ....................................................................... 6-21

6.6 REGISTER DESCRIPTIONS ................................................................................... 6-22

6.6.1 Control Block Registers .................................................................................... 6-22

6.6.2 Command Block Registers ............................................................................... 6-24

6.7 COMMAND DESCRIPTIONS................................................................................. 6-29

6.7.1 Recalibrate ........................................................................................................ 6-29

6.7.2 Read Sectors ..................................................................................................... 6-30

6.7.3 Write Sectors .................................................................................................... 6-31

6.7.4 Read Verify Sectors .......................................................................................... 6-32

6.7.5 Seek .................................................................................................................. 6-33

6.7.6 Execute Drive Diagnostics ............................................................................... 6-34

6.7.7 INITIALIZE DRIVE PARAMETERS .............................................................. 6-36

6.7.8 Download Microcode ....................................................................................... 6-37

6.7.9 SMART ............................................................................................................. 6-38

6.7.10 Read Multiple Sectors ...................................................................................... 6-48

6.7.11 Write Multiple Sectors ........................... ....................................... ...... ....... ...... 6-49

6.7.12 Set Multiple Mode ........................... ...... ...... ....... ...... ....... ...... ....... ...... ....... ...... 6-50

6.7.13 Read DMA ............................................. ...... ....... ...... ....... ...... ....... ...... ....... ...... 6-51

6.7.14 Write DMA ...... ....... ...... ....... ...... ....... ...... ...... ....... ...... ....... ...... .......................... 6-52

6.7.15 STANDBY IMMEDIATE ............................ ....... ...... ....... ...... ....... ...... ....... ...... 6-54

6.7.16 IDLE IMMEDIATE ......................................................... ...... ....... ...... ....... ...... 6-55

6.7.17 STANDBY ............................................. ...... ....... ...... ....................................... 6-56

6.7.18 IDLE .......... ...... ....... ...... ....... ...... ....... ...... ...... ....................................... ....... ...... 6-57

6.7.19 READ BUFFER ................... ...... ....... ...... ...... ....................................... ....... ...... 6-58

6.7.20 CHECK POWER MODE ................................................................................. 6-59

6.7.21 SLEEP .............................................. ...... ...... ....... ....................................... ...... 6-60

6.7.22 FLUSH CACHE ........................ ....... ...... ...... ....... ...... ....... ................................ 6-61

6.7.23 WRITE BUFFER .............................. ...... ...... ....... ...... ....... ...... ....... ...... ....... ...... 6-62

6.7.24 IDENTIFY DRIVE .................... ....... ...... ...... ....... ...... ....... ...... ....... ................... 6-63

6.7.25 Set Features EFh .............................................................................................. 6-71

6.7.26 Set Features (Ultra ATA/100) ......................................................................... 6-71

6.7.27 Read Defect List ............................................................................................... 6-72

6.7.28 Configuration ...................................................... ...... ....... ...... ....... ...... ....... ...... 6-75

6.7.29 Host Protected Mode Feature .......................................................................... 6-79

6.8 ERROR REPORTING............................................................................................... 6-86

Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT vi

List of Figures

List of FiguresList of Figures

List of Figures

Figure 3-1 Mechanical Dimensions of Quantum Fireball Plus AS Hard Disk Drive ......3-1

Figure 3-2 Drive Packing Assembly .................................................................................3-2

Figure 3-3 Drive Packing Assembly of a Polypropylene 20-Pack Container ...................3-3

Figure 3-4 Jumper Locations for the Quantum Fireball Plus AS Hard Disk Drive ........3-4

Figure 3-5 Jumper Locations on the Interface Connector ...............................................3-4

Figure 3-6 AT Connector and Jumper Location ..............................................................3-7

Figure 3-7 Mounting Dimensions for the Quantum Fireball Plus AS

Hard Disk Drives ..................................... ....... ...... ....... ...... ....... ...... ....... ...... ...3-9

Figure 3-8 Mounting Screw Clearance for the Quantum Fireball Plus AS

Hard Disk Drives ..................................... ....... ...... ....... ...... ....... ...... ....... ...... .3-10

Figure 3-9 J1 DC Power and ATA Bus Combination Connector ......................................3-11

Figure 3-10 Drive Power Supply and ATA Bus Interface Cables ....................................3-14

Figure 3-11 Completing the Drive Installation ................................................................3-15

Figure 5-1 Quantum Fireball Plus AS AT Hard Disk Drive Exploded View ..................5-2

Figure 5-2 Quantum Fireball Plus AS AT Hard Disk Drive Block Diagram ...................5-5

Figure 5-3 Block Diagram ................................................................................................5-6

Figure 5-4 Sector Data Field with ECC Check Bytes ....................................................5-14

Figure 6-1 PIO Interface Timing ....................................................................................6-10

Figure 6-2 Multiword DMA Bus Interface Timing ........................................................6-11

Figure 6-3 Initiating a Data In Burst ..............................................................................6-15

Figure 6-4 Sustained Data In Burst ...............................................................................6-15

Figure 6-5 Host Pausing a Data In Burst .......................................................................6-16

Figure 6-6 Device Terminating a Data In Burst .............................................................6-16

Figure 6-7 Host Terminating a Data In Burst ................................................................6-17

Figure 6-8 Initiating a Data Out Burst ...........................................................................6-17

Figure 6-9 Sustained Data Out Burst ............................................................................6-18

Figure 6-10 Device Pausing a Data Out Burst .................................................................6-18

Figure 6-11 Host Terminating a Data Out Burst .............................................................6-19

Figure 6-12 Device Terminating a Data out Burst ...........................................................6-20

Figure 6-13 Host Interface RESET Timing ......................................................................6-20

Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT vii

List of Tables

List of TablesList of Tables

List of Tables

Table 3-1 AT Jumper Options................................................................................................. 3-5

Table 3-2 J1 Power Connector, Section A............................................................................ 3-12

Table 3-3 Logical Addressing Format................................................................................... 3-17

Table 4-1 Specifications.......................................................................................................... 4-1

Table 4-2 Formatted Capacity ................................................................................................ 4-3

Table 4-3 Timing Specifications ............................................................................................. 4-4

Table 4-4 Power Reset Limits................................................................................................. 4-5

Table 4-5 Typical Power and Current Consumption.............................................................. 4-6

Table 4-6 Acoustical Characteristics—Sound Power............................................................. 4-7

Table 4-7 Environmental Specifications............ ....... ...... ...... ....... ....................................... .... 4-8

Table 4-8 Shock and Vibration Specifications....................................................................... 4-9

Table 4-9 Error Rates............................................................................................................ 4-11

Table 5-1 Cylinder Contents................................................................................................... 5-3

Table 5-2 Skew Offsets ......................................................................................................... 5-13

Table 6-1 Drive Connector Pin Assignments (J1, Section C) ............................................... 6-2

Table 6-2 Series Termination for Ultra ATA/100 .................................................................. 6-6

Table 6-3 Signal Line Definitions........................................................................................... 6-8

Table 6-4 Interface Signal Name Assignments....................................................................... 6-8

Table 6-5 PIO Host Interface Timing................................................................................... 6-10

Table 6-6 Multiword DMA Host Interface Timing .............................................................. 6-11

Table 6-7 Ultra DMA Data Transfer Timing Requirements................................................. 6-12

Table 6-8 Ultra DMA Data Burst Timing Descriptions ....................................................... 6-13

Table 6-9 Host Interface RESET Timing.............................................................................. 6-20

Table 6-10 I/O Port Functions and Selection Addresses....................................................... 6-21

Table 6-11 Command Block Register Initial Values............................................................... 6-22

Table 6-12 Device Control Register Bits ................................................................................ 6-23

Table 6-13 Drive Address Register Bits.................................................................................. 6-24

Table 6-14 Error Register Bits ................................................................................................ 6-25

Table 6-15 Drive Head Register Bits ...................................................................................... 6-26

Table 6-16 Status Register Bits............................................................................................... 6-27

Table 6-17 Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT

Command Codes and Parameters......................................................................... 6-28

Table 6-18 Diagnostics Codes................................................................................................. 6-34

Table 6-19 Device Attribute Thresholds Data Structure ...................................................... 6-43

Table 6-20 Individual Threshold Data Structure .................................................................. 6-43

Table 6-21 Device SMART Data Structure............................................................................ 6-44

Table 6-22 Valid Count Range................................................................................................ 6-56

Table 6-23 Sector Count Result Value and Status................................................................. 6-59

Table 6-24 Identify Drive Parameters..................................................................................... 6-65

Table 6-25 Transfer/Mode Values .......................................................................................... 6-71

Table 6-26 READ DEFECT LIST LENGTH Command Bytes .............................................. 6-72

Table 6-27 AT READ DEFECT LIST Command Bytes ......................................................... 6-73

Table of Contents

viii Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT

Table 6-28 DEFECT LIST DATA FORMAT.......................................................................... 6-74

Table 6-29 DEFECT ENTRY DATA FORMAT...................................................................... 6-74

Table 6-30 Accessing the READ CONFIGURATION Command.......................................... 6-75

Table 6-31 Accessing the SET CONFIGURATION Command ............................................. 6-76

Table 6-32 Accessing the SET CONFIGURATION WITHOUT

SAVING TO DISK Command.............................................................................. 6-77

Table 6-33 Configuration Command Format.......................................................................... 6-78

Table 6-34 Command Errors ................................................................................................... 6-86

Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT 1-1

Chapter 1

Chapter 1Chapter 1

Chapter 1

ABOUT THIS MANUAL

ABOUT THIS MANUALABOUT THIS MANUAL

ABOUT THIS MANUAL

This chapter gives an overview of the contents of this manual, including the
intended audience, how the manual is organiz ed, terminology and conventions, and
references.

1.1

1.11.1

1.1 AUDIENCE

AUDIENCEAUDIENCE

AUDIENCE

The Quantum Fireball Plus ASM™10.2/20.5/30.0/40.0/60.0 GB AT Product
Manual is intended for several audiences. These audiences include: the end user,
installer, developer, original equipment manufacturer (OEM), and distributor. The
manual provides information about installation, principles of operation, interface
command implementation, and maintenance.

1.2

1.21.2

1.2 MANUAL ORGANIZATION

MANUAL ORGANIZATIONMANUAL ORGANIZATION

MANUAL ORGANIZATION

This manual is org anized into the following chapters:

•Chapter 1 – About This Manual

•Chapter 2 – General Description

•Chapter 3 – Installation

•Chapter 4 – Specifications

•Chapter 5 – Basic Principles of Operation

•Chapter 6 – ATA Bus Interface and ATA Commands

1.3

1.31.3

1.3 TERMINOLOGY AND CONVENTIONS

TERMINOLOGY AND CONVENTIONSTERMINOLOGY AND CONVENTIONS

TERMINOLOGY AND CONVENTIONS

In the Glossary at the back of this manual, you can find definitions for many of the
terms used in this manual. In addition, the following abbreviations are used in this
manual:

• ASIC application-specific integrated circuit

• ATA advanced technology attachment

• bpi bits per inch

• dB decibels

• dBA decibels, A weighted

About This Manual

1-2 Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT

• ECC error correcting code

• fci flux changes per inch

•Hz hertz

•KB kilobytes

• LSB least significant bit

• mA milliamperes

• MB megabytes (1 MB = 1,000,000 bytes when referring to disk
storage and 1,048,576 bytes in all other cases)

• Mbit/s megabits per second

•MB/s megabytes per second

•MHz megahertz

•ms milliseconds

• MSB most significant bit

• mV millivolts

•ns nanoseconds

•tpi tracks per inch

•µs microseconds

•V volts

The typographical and naming conventions used in this manual are listed below.
Conventions that are unique to a specific table appear in the notes that follow that
table.

Typographical Conventions:

• Names of Bits: Bit names are presented in initial capitals. An example

is the Host Software Reset bit.

• Commands: Interface commands ar e listed in all capita ls. An example

is WRITE LONG.

• Register Names: Registers are g iven in this manual with initial

capitals. An example is the Alternate Status Register.

• Parameters: Pa rameter s are gi ven as init ial c apitals wh en spel led ou t,

and are given as all capi tals whe n a bbrevia te d. E xamples are Pref et ch
Enable (PE), and Cache Enable (CE).

• Hexadecimal Notation: The hexadecimal notation is given in 9-point

subscript form. An example is 30

H

.

• Signal Negation: A signal name that is defined as active low is listed

with a minus sign following the signal. An example is RD–.

• Messages: A message that is sent from the drive to the host is listed in

all capitals. An example is ILLEGAL COMMAND.

About This Manual

Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT 1-3

Naming Conventions:

• Host: I n general, the system in which the d rive reside s is refe rred to as
the host.

• Computer Voice: This refers to items you type at the computer
keyboard. These items are listed in 10-point, all capitals, Courier font.
An example is FORMAT C:/S.

1.4

1.41.4

1.4 REFERENCES

REFERENCESREFERENCES

REFERENCES

For additional information about the AT interface, refer to:

• IBM Technical Reference Manual #6183355, March 1986.

• ATA Common Access Method Specification, Revision 5.0.

About This Manual

1-4 Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT

Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT 2-5

Chapter 2

Chapter 2Chapter 2

Chapter 2

GENERAL DESCRIPTION

GENERAL DESCRIPTIONGENERAL DESCRIPTION

GENERAL DESCRIPTION

This chapter summarizes the general functions and key features of the Quantum
Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT hard disk drives, as well as the
applicable standards and regulations.

2.5

2.52.5

2.5 PRODUCT OVERVIEW

PRODUCT OVERVIEWPRODUCT OVERVIEW

PRODUCT OVERVIEW

Quantum’s Fireball Plus AS hard disk drives are part of a family of high
performance, 1-inch-high hard disk drives manufactured to meet the highest
product quality standards.

These hard disk drives use nonremovable, 3 1/2-inch hard disks and are
available with the ATA interface.

The Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT hard disk drives
feature an embedded hard disk drive controller, and use ATA commands to
optimize system performance. Because the drive manages media defects and error
recovery internally, these operations are fully transparent to the user.

The innovative design of the Quantum Fireball Plus AS hard disk drives
incorporate leading edge technologies such as Ultra ATA/100, Advanced Cache
Management, Shock Protection System™(SPS), Data Protection System (DPS )
and Quiet Drive Technology (QDT). Thes e enhanced techn ol ogi e s enab l e
Quantum to produce a family of high-p erformance, high-reliability drives.

2.6

2.62.6

2.6 KEY FEATURES

KEY FEATURESKEY FEATURES

KEY FEATURES

The Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT hard disk drives
include the following key features:

General

• Formatted storage capacity of 10.2 GB (1 disk, 1 head), 20.5 GB (1 disk, 2
heads), 30.0 GB (2 disks, 3 heads), 40.0 GB (2 disks, 4 heads), and 60.0 GB
(3 disks, 6 heads)

• Low profile, 1-inch height

• Industry standard 3 1/2-inch form factor

• Emulation of IBM

®

PC AT® task file register, and all AT fixed disk

commands

• Windows NT and 9X Certification

General Description

2-6 Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT

Performance

• Average seek time of 8.5 ms

• Average rotational latency of 4.17 ms

• New Ultra ATA interface with Quantum-patented Ultra ATA/100 protocol
supporting burst data transfer rates of 100 MB/s.

• 2 MB buffer with 1.9 MB (approximate) Advance Cache Management
(ACM).

• Look-ahead DisCache feature with continuous prefetch and WriteCache
write-buffering capabilities

• AutoTask Register update, Multi-block AutoRead, and Multi-block
AutoWrite features in a custom ASIC

• Read-on-arrival firmware

• Quadruple-burst ECC, and double burst ECC on-the-fly

• 1:1 interleave on read/write operations

• Support of all standard ATA data transfer modes with PIO mode 4 and
multiword DMA mode 2, and Ultra DMA modes 0, 1, 2, 3, 4 and 5

• Adaptive cache segmentation

Reliability

• 625,000 hours mean time between failure (MTBF) in the field

• Automatic retry on read errors

• 344-bit, interleaved Reed-Solomon Error Correcting Code (ECC ), with cross
checking correction up to four separate bursts of 32 bits each totalling up to
128 bits in length

• S.M.A.R.T. 4 (Self-Monitoring, Analysis and Reporting Technology)

•Patented Airlock

®

automatic shipping lock, magnetic actuator retract, and

dedicated landing zone

• Transparent media defect mapping

• High performance, in-line defective sector skipping

• Reassignment of defective sectors discovered in the field, without
reformatting

• Shock Protection System to reduce handling induced failures

• Data Protection System to verify drive integrity

• Quiet Drive Technology (QDT)

Versatility

•Power saving modes

•Downloadable firmware

• Cable select feature

• Ability to daisy-chain two drives on the interface

General Description

Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT 2-7

2.7

2.72.7

2.7 Regulatory Compliance Standards

Regulatory Complianc e StandardsRegulatory Compliance Standards

Regulatory Complianc e Standards

Quantum Corporation’s disk drive products meet all domestic and international
product safety regulatory compliance requirements. Quantum’s disk drive products
conform to the following specifically marked Product Safety Standards:

• Underwriters Laboratories (UL) Standard 1950. This certificate is a
category certification pertaining to all 3.5-inch series drives models.

• Canadian Standards Association (CSA) Standard C.22.2 No. 1950.
This certificate is a category certification pertaining to all 3.5-inch
series drives models.

• TUV Rheinland Standard EN60 950. This certificate is a category
certification pertaining to all 3.5-inch series drives models.

Product EMI/EMS Qualifications:

Product EMI/EMS Qualifications:Product EMI/EMS Qu alifications:

Product EMI/EMS Qualifications:

• CE Mark authorization is granted by TUV Rheinland in compliance
with our qualifying under EN 55022:1994 and EN 50082-1:1997.

• C-Tick Mark is an Australian authorization marked noted on
Quantum’s disk drive products. The mark proves con formity to the
regulatory compliance document AS/NZS 3548: 1995 and BS EN
55022: 1995.

• Quantum’s disk drives are designed as a separate subas sembly that conforms
to the FCC Rules for Radiated and Conducted emissions, Part 15 Subpart J;
Class B when installed in a given computer system.

• Approval from Taiwan BSMI. Number: 3892A638

2.8

2.82.8

2.8 HARDWARE REQUIREMENTS

HARDWARE REQUIREMENTSHARDWARE REQUIREMENTS

HARDWARE REQUIREMENTS

The Quantum Fireball Plus AS hard disk drives are compatible with the IBM PC
AT, and other computers that are compatible with the IBM PC AT. It connects to
the PC either by means of a third-part y IDE-compatible adapter board, or b y
plugging a cable from the drive directly into a PC motherboard that supplies an
ATA interface.

General Description

2-8 Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT

Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT 3-1

Chapter 3

Chapter 3Chapter 3

Chapter 3

INSTALLATION

INSTALLATIONINSTALLATION

INSTALLATION

This chapter explains how to unpack, configure, mount, and connect the Quantum
Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT hard disk drive prior to
operation. It also explains how to start up and operate the drive.

3.1

3.13.1

3.1 SPACE REQUIREMENTS

SPACE REQUIREMENTSSPACE REQUIREMENTS

SPACE REQUIREMENTS

The Quantum Fireball Plus AS hard disk drives are shipped without a faceplate.
Figure 3-1 shows the external dimensions of the Quantum Fireball Plus AS 10.2/

20.5/30.0/40.0/60.0 GB AT drives.

Figure 3-1

Figure 3-1 Figure 3-1

Figure 3-1

Mechanical Dimensions of Quantum Fireball Plus AS Hard Disk Drive

26.1 mm (max)
(1.00 inches)

101.6 ± 0.25 mm
(4.00 inches)

147 mm (max)
(5.75 inches)

Installation

3-2 Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT

3.2

3.23.2

3.2 UNPACKING INSTRUCTIONS

UNPACKING INSTRUCTIONS UNPACKING INSTRUCTIONS

UNPACKING INSTRUCTIONS

1. Open the shipping container and remove the packing assembly that
contains the drive.

2. Remove the driv e from th e packing assembly.

3. When you are ready to install the drive, remove it from the ESD bag.

Figure 3-2 shows the packing assembly for a single Quantum Fireball Plus AS
hard disk drive. A 20-pack shipping container is available for multiple drive
shipments.

Figure 3-2

Figure 3-2 Figure 3-2

Figure 3-2

Drive Packing Assembly

CAUTION:

CAUTION:CAUTION:

CAUTION: The maximum limits for phys ical shock can be exceeded if the

drive is not handled properly. Special care should be
taken not to bump or drop the drive. It is highly recommended
that Quantum Fireball Plus AS drives are not stacked or placed
on any hard surface after they ar e unpacked. Such handling
could cause media damage.

CAUTION:

CAUTION:CAUTION:

CAUTION: During shipment and handling, the antistatic electrostatic dis-

charge (ESD) bag prevents electronic component
damage due to electrostati c discharge. To av oid accidental dam­age to the drive, do not use a sharp instrume nt to open the ESD
bag and do not touch PCB components. Save the packing mate­rials for possible future use.

Installation

Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT 3-3

Figure 3-3

Figure 3-3 Figure 3-3

Figure 3-3 Drive Packing Assembly of a Polypropylene 20-Pack Container

Note: The 20-pack container should be shipped in the same way it

was received from Quantum. When individual drives are
shipped from the 20-pack container then it should be appropri­ately packaged (n ot supplied wi th the 20-pack) to prevent dam­age.

Installation

3-4 Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT

3.3

3.33.3

3.3 HARDWARE OPTIONS

HARDWARE OPTIONSHARDWARE OPTIONS

HARDWARE OPTIONS

The configuration of a Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB
AT hard disk dr iv e d ep end s on th e h os t syst em in wh i ch i t is t o be ins ta ll ed. T hi s
section describes the hardware options that you must take into account prior to
installation. Figure 3-4 shows the printed circuit board (PCB) assembly,
indicating the jumpers that control some of these options.

Figure 3-4

Figure 3-4 Figure 3-4

Figure 3-4

Jumper Locations for the Quantum Fireball Plus AS Hard Disk Drive

Figure 3-5

Figure 3-5 Figure 3-5

Figure 3-5 Jumper Locations on the Interface Connector

DC Power
Connector

Jumpers

ATA-Bus
Interface
Header

Back of

Drive

Front

Drive

Installation

Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT 3-5

The configuration of the following Three jumpers controls the drive’s five modes
of operation:

•CS – Cable Select

• DS – Drive Select

•PK– Jumper Parking Position (Slave mode)

• AC– Alternate Capacity

The AT PCB has two jumper locatio ns provided to configure t he drive in a system.
The default configuration for the drive as shipped from the factory is with a
jumper across the DS location, and open positions in the CS, PK and AC
positions.

Table 3-1 defines the operation of the master/slave jumpers and their function
relative to pin 28 on the interface. 1 indicates that the specified jumper is installed;
0 indicates that the jumper is not installed.

Table 3-1

Table 3-1 Table 3-1

Table 3-1

AT Jumper Options

Note: In Table 3-1, a 0 indicates that the jumper is removed, a 1 indi-

cates that the jumper is installed, and an X indicates that the
jumper setting does not matter.

3.3.1

3.3.13.3.1

3.3.1 Cable Select (CS) Jumper

Cable Select (CS) JumperCable Select (CS) Jumper

Cable Select (CS) Jumper

When a Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT hard disk
drive and another ATA hard disk drive are daisy-chained together, they can be
configured as Master or Slave either by the CS or DS jumpers. To configure the
drive as a Master or Slav e with the CS feature, the CS jumper is in stalled (1). Th e
drive's position on the 80 conductor Ultra ATA data cable then determines
whether the drive is a Master (Device 0) or a Slave (Device 1). If the drive is
connected to the end of the Ultra (cable Select) data cable the drive is a Master.
If the drive is connected to the middle connection it is set as a Slave.

Once you install the C S jumper, the driv e is configured as a Ma ster or Slave by t he
state of the Cable Sele ct signal: pin 28 of the ATA bus conne ctor. Please no te that
pin 28 is a vendor-specific pin that Quantum is using for a specific purpose. More
than one function is allocated to CS, according to the ATA CAM specification
(see reference to this specification in Chapter 1). If pin 28 is a 0 (grounded), the

CS

CSCS

CS DS

DSDS

DS PK

PKPK

PK PIN 28

PIN 28PIN 28

PIN 28 DESCRIPTION

DESCRIPTIONDESCRIPTION

DESCRIPTION

0 0 X X Drive is configured as a slave
1 0 X Gnd Drive is configured as Master (Device 0) when attached

to the end of a 80 conductor Ultra ATA cable
0 1 X X Drive is configured as a Master
1 0 X Open Drive is configured as a Slave (Device 1) when attached

to the middle of a 80 conductor Ultra ATA cable
1 1 X X Drive is configured as a Master with an attached slave

that does not support DASP

Installation

3-6 Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT

drive is configured as a Master. If it is a 1 (high), the drive is configured as a Slave.
In order to configure two drives in a Master/Slave relationship using the CS
jumper, you need to use a cable that provides the proper signal level at pin 28 of
the ATA bus connector. This allows two drives to operate in a Master/Slave
relationship according to the drive cable placement.

The Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT hard disk drives
are shipped from the f actory as a Master (Device 0 - CS jumper installed). To
configure a drive as a Slave (Device 1- DS scheme), the CS jumper must be
removed. In this configuration, the spare jumper removed from the CS position
may be stored on the PK jumper pins.

3.3.2

3.3.23.3.2

3.3.2 Drive Select (DS) Jumper

Drive Select (DS) JumperDrive Select (DS) Jumper

Drive Select (DS) Jumper

You can also daisy-chain two drives on the ATA bus interface by using their Drive
Select (DS) jumper s. To use th e DS fea ture, th e CS ju mper must not be inst alled .

To configure a drive as the Master (Device 0), a jumper must be installed on the
DS pins.

Note: The order in which drives are connected in a daisy chain has no

significance.

3.3.3

3.3.33.3.3

3.3.3 Master Jumper configuration

Master Jumper configurationMaster Jumper configuration

Master Jumper configuration

In combination with the current DS or CS jumper s ettings, the Slave Present (SP)
jumper can be implemented if necessary as follows:

Note: The CS position doubles as the Slave present on this drive.

• When the drive is configured a s a Master

(DS jumper install ed or CS

jumper installed, and the Cable Select signal is set to (0), adding an
additional jumper (both jumpers DS and CS now installed) will
indicate to the drive that a Slave drive is present. This Master with
Slave Present jumper configuration shoul d be instal led on the Master
drive only if the Slave drive does not use the Drive Active/Slave
Present (DASP–) signal to indicate its presence.

3.3.4

3.3.43.3.4

3.3.4 Jumper Parking (PK) Position

Jumper Parking (PK) PositionJumper Parking (PK) Position

Jumper Parking (PK) Position

The PK position is used as a holding place for the jumper for a slave drive in
systems that do not su pport Cable Select. The pins used for the parking positio n
are vendor unique.

Installation

Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT 3-7

3.3.5

3.3.53.3.5

3.3.5 Alternate Capacity (AC)

Alternate Capacity (AC)Alternate Capacity (AC)

Alternate Capacity (AC)

For user capacities below 66,055,248 sectors (32 GB), inserting the AC jumper
limits the Number of Cylinders field 1 to a value of 16,383, as reported in
IDENTIFY DEVICE data word. This allows software drivers to determine that the
actual capacity is larger than indicated by the maximum CHS, requiring LBA
addressing to use the full capacity.

A summary of these effects for the Quantum Fireball Plus AS drives is shown in
the following table:

Figure 3-6

Figure 3-6 Figure 3-6

Figure 3-6

AT Connector and Jumper Location

AC JUMPER OUT

AC JUMPER OUTAC JUMPER OUT

AC JUMPER OUT AC JUMPER IN

AC JUMPER INAC JUMPER IN

AC JUMPER IN

10 GB

10 GB10 GB

10 GB

C=16,383
H=16
S=63
LBA=20,075,548

C=16,383
H=15
S=63
LBA=20,075,548

20 GB

20 GB20 GB

20 GB

C=16,383
H=16
S=63
LBA=40,157,056

C=16,383
H=15
S=63
LBA=40,157,056

40 GB

40 GB40 GB

40 GB

C=16,383
H=16
S=63
LBA=80,315,072

C=16,383
H=16
S=63
LBA=66,055,248

60 GB

60 GB60 GB

60 GB

C=16,383
H=16
S=63
LBA=120,478,088

C=16,383
H=16
S=63
LBA= 66,055,248

Installation

3-8 Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT

3.4

3.43.4

3.4 ATA BUS ADAPTER

ATA BUS ADAPTERATA BUS ADAPTER

ATA BUS ADAPTER

There are two ways you can configure a system to allow the Quantum Fireball Plus
AS hard disk drives to communicate over the ATA bus of an IBM or IBM­compatible PC:

1. Connect the drive to a 40-pin ATA bus connector (if available) on the
motherboard of the PC.

2. Install an IDE-compatible adapter board in the PC, and connect the drive
to the adapter board.

3.4.1

3.4.13.4.1

3.4.1 40-Pin ATA Bu s Connector

40-Pin ATA Bus Connector40-Pin ATA Bus Connector

40-Pin ATA Bus Connector

Most PC motherboards have a built-in 40-pin ATA bus connector that is
compatible with the 40-pin ATA interface of the Quantum Fireball Plus AS 10.2/

20.5/30.0/40.0/60.0 GB AT hard disk drives. If the motherboard has an ATA
connector, simply connect a 40-pin ribbon cable between the drive and the
motherboard.

You should also refer to the moth erboard instruction manual, and refer to Chapt er
6 of this manual to ensure signal compatibility.

3.4.2

3.4.23.4.2

3.4.2 Adapter Board

Adapter BoardAdapter Board

Adapter Board

If your PC motherboard does not contain a built-in 40-pin ATA bus interface
connector, you must install an ATA bus adapter board and connecting cable to
allow the drive t o interface with the mo therboard. Quantum does not supply such
an adapter board, but they are available from several third-party vendors.

Please carefully read the instruction manual that comes with your adapter board,
as well as Chapter 6 of this manual to ensure signal compatibility between the
adapter board and the drive. Also, make sure that the adapter board jumper
settings are appropriate.

Installation

Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT 3-9

3.5

3.53.5

3.5 MOUNTING

MOUNTINGMOUNTING

MOUNTING

Drive mounting orientation, clearance, and ventilation requirements are
described in the following subsections.

3.5.1

3.5.13.5.1

3.5.1 Orientation

OrientationOrientation

Orientation

The mounting holes on the Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0
GB AT hard disk drives allow the drive to be mounted in any orientation. Figure
3-6 and Figure 3-7 show the location of the three mounting holes on each side of
the drive. The drive can also be mounted using the four mounting hole locations
on the PCB side of the drive.

Note: It is highly recommended that the drive is hard mounted on to

the chassis of the system being used for general operation, as
well as for test purposes. Failure to hard mount the drive can
result in erroneous errors during testing.

Drives can be mounted in any orientation. Normal position is

with the PCB facing down.
All dimensions are in millimeters. For mounting, #6-32 UNC screws are
recommended.

Figure 3-7

Figure 3-7 Figure 3-7

Figure 3-7

Mounting Dimensions for the Quantum Fireball Plus AS Ha rd Disk Drives

Installation

3-10 Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT

Figure 3-8

Figure 3-8 Figure 3-8

Figure 3-8 Mounting Screw Clearance for the Quantum Fireball Plus AS Hard Disk Drives

CAUTION:

CAUTION:CAUTION:

CAUTION: The PCB is very close to the mounting holes. Do not ex-

ceed the specified length for the mounting screws. The
specified screw length allows full use of the mounting
hole threads, while avoiding damaging or placing un­wanted stress on the PCB. Figure 3-8 specifies the min­imum clearance between the PCB and the screws in the
mounting holes. To avoid stripping the mounting hole
threads, the maximum torque applied to the screws must
not exceed 8 inch-pounds. A maximum screw length of

0.25 inches may be used.

Installation

Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT 3-11

3.5.2

3.5.23.5.2

3.5.2 Clearance

ClearanceClearance

Clearance

Clearance from the drive to any other surface (excep t mounting surfaces) must be
a minimum of 1.25 mm (0.05 inches).

3.5.3

3.5.33.5.3

3.5.3 Ventilation

VentilationVentilation

Ventilation

The Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT hard disk drives
operate without a cooling fan, provided the ambient air temperature does not
exceed 131°F (55°C) at any point along the drive form factor envelope.

3.6

3.63.6

3.6 COMBINATION CONNECTOR (J1)

COMBINATION CONNECTOR (J1)COMBINATION CONNECTOR (J1)

COMBINATION CONNECTOR (J1)

J1 is a three-in-one combination connector. The drive’s DC power can be applied
to section A. The ATA bus interface (40-pin) uses section C. The connector is
mounted on the back edge of the printed-circuit board (PCB), as shown in Figure
3-9.

Figure 3-9

Figure 3-9 Figure 3-9

Figure 3-9

J1 DC Power and ATA Bus Combination Connector

4321

4-Pin DC Power

(J1 Section A)

40-Pin IDE

(J1 Section C)

J1 IDE (40-Pin)/DC (4-Pin)

Combination Connector

Pin 1

Pin 40

Installation

3-12 Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT

3.6.1

3.6.13.6.1

3.6.1 DC Power (J1, Section A)

DC Power (J1, Section A)DC Power (J1, Section A)

DC Power (J1, Section A)

The recommended mating conne ctors for the +5 VDC and +12 VDC input power
are listed in Table 3-2.

Table 3-2

Table 3-2 Table 3-2

Table 3-2

J1 Power Connector, Section A

Note: Labels indicate the pin numbers on the connector. Pins 2 and 3 of

section A are the +5 and +12 volt returns and are connected to­gether on the drive.

3.6.2

3.6.23.6.2

3.6.2 External Drive Activity LED

External Drive Activity LED External Drive Activity LED

External Drive Activity LED

An external drive activity LED may be connected to the DASP-I/O pin 39 on J1.
For more details, see the pin description in Table 6-1.

3.6.3

3.6.33.6.3

3.6.3 ATA Bus Interface Connector (J1, Section C)

ATA Bus Interface Connector (J1, Section C)ATA Bus Interface Connector (J1, Section C)

ATA Bus Interface Connector (J1, Section C)

On the Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT hard disk
drives, the ATA bus interface cable c onnector (J1, section C) is a 40-pin Uni versal
Header, as shown in Figure 3-9.

To prevent the possibility of incorrect installation, the connector h as been keyed
by removing Pin 20. This ensures that a connector cannot be installed upside
down.

See Chapter 6, “ATA Bus Interface and ATA Commands,” for more detailed
information about the required signals. Refer to Table 6-1 for the pin assignments
of the ATA bus connector (J1, section C).

PIN

PINPIN

PIN

NUMBER

NUMBERNUMBER

NUMBER

VOLTAGE

VOLTAGEVOLTAGE

VOLTAGE

LEVEL

LEVELLEVEL

LEVEL

MATING CONNECTOR TYPE AND PART NUMBER

MATING CONNECTOR TYPE AND PART NUMBERMATING CONNECTOR TYPE AND PART NUMBER

MATING CONNECTOR TYPE AND PART NUMBER

(OR EQUIVALENT)

(OR EQUIVALENT)(OR EQUIVALENT)

(OR EQUIVALENT)

J1 Section A (4-Pin):

1 +12 VDC 4-Pin Connector:

AMP P/N 1-480424-0
Loose piece contacts:
AMP P/N VS 60619-4
Strip contacts:
AMP P/N VS 61117-4

2 Ground

Return for
+12 VDC

3 Ground

Return for
+5 VDC

4+5 VDC

Installation

Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT 3-13

3.7

3.73.7

3.7 FOR SYSTEMS WITH A MOTHERBOARD ATA ADAPTER

FOR SYSTEMS WITH A MOTHERBOARD ATA ADAPTERFOR SYSTEMS WITH A MOTHERBOARD ATA ADAPTER

FOR SYSTEMS WITH A MOTHERBOARD ATA ADAPTER

You can install the Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT
hard disk drives in an AT-compatible system that contains a 40-pin ATA bus
connector on the motherboard.

To connect the drive to the motherboard, use a 40 conductor ribbon cable (80
conductor ribbo n cable if using Ultra ATA/100 drive) 18 inches in length or
shorter. Ensure that pin 1 of the drive is connected to pin 1 of the motherboard
connector.

3.8

3.83.8

3.8 FOR SYSTEMS WITH AN ATA ADAPTER BOARD

FOR SYSTEMS WITH AN ATA ADAPTER BOARDFOR SYSTEMS WITH AN ATA ADAPTER BOARD

FOR SYSTEMS WITH AN ATA ADAPTER BOARD

To install the Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT hard
disk drive in an AT-compatible system without a 40-pin ATA bus connector on its
motherboard, you need a third-party IDE-compatible adapter board.

3.8.1

3.8.13.8.1

3.8.1 Adapter Board Installation

Adapter Board InstallationAdapter Board Installation

Adapter Board Installation

Carefully read the manual that accompanies your adapter board before installing
it. Make sure that all the jumpers are set p roperly and th at there are no add ress or
signal conflicts. You must also investigate to see if your AT-compatible system
contains a combination floppy and hard disk controller board. If it does, you must
disable the hard disk drive controller functions on that controller board before
proceeding.

Once you have disabled the hard disk drive controller functions on the floppy/
hard drive controller, install the adapter board. Again, make sure that you have
set all jumper straps on the adapter board to avoid addressing and signal conflicts.

Note: For Sections 3.7 and 3.8, power should be turned off on the

computer before installing the drive.

Installation

3-14 Quantum Fireball Plus AS 10.2/20.5/30.0/40.0/60.0 GB AT

3.8.1.1

3.8.1.13.8.1.1

3.8.1.1 Connecting the Adapter Boa rd and the Drive

Connecting the Adapter Board and the DriveConnecting the Adapter Board and the Drive

Connecting the Adapter Board and the Drive

Use a 40-pin ribbon cable to connect the drive to the board. See Figure 3-10. To
connect the drive to the board:

1. Insert the 40-pin cable connector into the mating connector of the adapter
board. Make sure that pin 1 of th e connect or matches with pi n 1 on the cabl e.

2. Insert the other end of the cable into the header on the drive. When
inserting t his end of th e cable , make s ure th at pin 1 of th e cable connec ts
to pin 1 of the drive connector.

3. Secure the drive to the system chassis by using the mounting screws, as
shown in Figure 3-11.

Figure 3-10

Figure 3-10 Figure 3-10

Figure 3-10

Drive Power Supply and ATA Bus Interface Cables