Quantum 860450 User manual

Video LED Ring Light

● Variable Color Temperature

● Variable Dimming

● Programmable Light Setting

● Automatic Lighting Track (ALT)

Omicron 4 – OM4

1.0 Introduction

Omicron 4 is a lightweight, versatile, high power LED ring light.

Omicron 4 provides continuous high quality video LED lighting. Designed
specifically for 35mm DSLR type cameras, Omicron 4 can be easily adapted to
other video camera types.

Omicron 4‘s “chromatically correct” light spectrum emanates from 64 critically
color-balanced LEDs. A balanced mix of cool white, warm white and colored
LEDs fill in the spectral gaps that are characteristic of white-only LED lights.

The wide range of adjustable color temperature (2500K – 6500K) of Omicron 4
can emulate traditional daylight and tungsten sources.

The light intensity of Omicron 4 can be dimmed from 100% to 0% without
altering color temperature.

The Automatic Lighting Track (ALT) will automatically adjust Omicron 4’s light
intensity as ambient lighting conditions change, or the distance to the subject
changes.

The light intensity and color temperature can be stored into 8 Pre-sets and can
be quickly recalled when needed.

Omicron 4 can be powered from any standard 12 – 24 volt industrial video
battery pack such as a V-mount battery. Quantum offers several choices – see
Section 3.2 and 5.0. An AC power supply is included with the Omicron 4.

2.0 Overview

The Quantum Omicron 4 (OM4) Video LED Ring Light for video operation
consists of:

OM4 - Variable Color Temperature Ring Light
OM44 - AC Adapter for operating OM4 using 110V-240V AC power source

2.1 Additional Accessories

OM41 – Power cable to power OM4 by V mount Battery.

OM43 – Power cable to power OM4 by Quantum QB8 or T3 battery pack.

QB8 – Quantum battery pack to power OM4 and DSLR cameras.

3.0 Mounting & Power Accessories

On
Press and hold the Power
button until the digital display
shows “ON”. The OM4 light
output will gradually increase
to the last intensity setting
used. The intensity level (0 –

100) will appear on the
display.

Off
Press and hold the Power
button until the digital display
shows “OFF”. The OM4 light
will gradually dim.

Connect a power
source to the Omicron

4. See Section 3.2 for
a list of power sources.

The digital display shows
“rdY” and will blink once per
second. The OM4 is ready to
operate.

If the digital display blinks “Lb”.

It indicates the voltage of the
power source is too low to
operate. Check the battery
pack operation.

The battery may need charging

75

Adjust the light intensity

Turn the Mode knob
clockwise to increase the
light intensity, count­clockwise to decrease the
light intensity.

Power button

Mode Knob

3.1 Mounting
QF29 – for under camera mounting OM42 – for twin rail mounting

3.2 Power

AC Power – OM44 (provided)

DC Power
V Mount Battery – using OM41 power cable

Quantum QB8, T3 – using OM43 power cable

4.0 Operation

4.1 Connections

4.2 ON / OFF

4.3 Adjust Light Intensity (0 – 100%)

Push and release the Mode knob, the display shows the intensity 0 – 100%.

4.4 Adjust Color Temperature (2500 – 6500)

Adjust the color temperature

Turn the Mode knob clockwise to increase the
color temperature (towards cool), count­clockwise to decrease the color temperature
(towards warm).

Turn ON ALT

While aiming at your subject, momentarily push the
Power button one, or more times, until the display
shows “Auto”.

Turn OFF the ALT

Push the Power button once. The display will
show the light intensity level.

3500

P-on

P3

P3

Poff

Push and release the Mode knob, the display shows the 4 digit color
temperature (2500 – 6500).

4.5 Automatic Lighting Track (ALT) Operation

Automatic Lighting Track (ALT) Operation will keep constant illumination on the
subject when the distance between it and the OM4 LED Ring Light changes.
ALT reacts faster than the aperture controlled exposure of most video and
HDSLR cameras.

Turn OM4 ON

With the OM4 turned on, place it at the maximum distance you intend to shoot from your
subject. Set the intensity knob to 100. Your minimum shooting distance will be one half of
your maximum.

Indications

If the digital display shows “HI”, you are too close to your subject and you need to move
away.
If the digital display shows “Lo”, you are too far from your subject and you need to move
closer.

4.6 Pre-set Mode (P)

In Pre-set mode light intensity and color temperature may be saved for later
use. There are 8 Pre-sets, labeled P1, P2, . . . P8, that can be quickly recalled
when needed.

To enter Pre-set mode,
Push the Mode knob down until P-on
appears in the display (approx. 2s)

To recall Pre–sets
Rotate the Mode knob to scroll through P1 – P8, then push and release the
Mode knob.

The color temperature for that pre-set will display for 1 second, then the light
intensity will be displayed.

Adjusting your Pre-sets
Once you have located a Pre-set P1 – P8, you can adjust and store the color
temperature and light intensity.

Push and release the Mode knob to adjust the desire light intensity (see 4.3)
Push and release the Mode knob to adjust color temperature (see 4.4).
Push and release the Mode knob to show current Pre-set number.
(rotate adjustment to select a different Pre-set number if desired)
.
Press and hold the Mode knob, Pre-set number will blink.
When number stops blinking the settings
have been saved.

To exit Pre-set Mode:

Push and release Mode knob to show current Pre-set number.
Rotate the Mode knob until the display shows Poff.
Push and release the Mode knob to exit.

5.0 Specifications

Light Output: 255fc / 2700lux 1.5ft/ .5m

72fc / 750lux 3ft / 1m
17fc / 170lux 7ft / 2m

Light output adjustment: 0 – 100%

Color temperature adjustment range: 2500 – 6500K

Illumination Angle: 60 Degree

Ring Size: 9.25in x 1.1in / 235mm x 28mm

Weight: 20oz / 560g

Housing: (widest point) 2 in / 50mm

Maximum Lens Diameter: 3.9 in / 100mm

Power: 30W

Input Voltage: 12 – 24V DC

Power Source: Full Power Run Time (Approx):

Quantum T3 1 Hr

Quantum QB8 2 Hrs

V-Mount Battery: 90WHr 3 Hrs

160WHr 5 Hrs

AC Power:
Quantum OM44 (included) Unlimited

6.0 Customer Service

Having any trouble using your Quantum product? We are here to help. Mail,
call, fax, or email our Service Department:

Service department

Quantum Instruments Inc

10 Commerce Drive

Hauppauge, NY 11788

Tel: [phone] Fax: [phone]

Website: www.qtm.com

Troubleshooting tips are available at www.qtm.com, Support, Customer
Support, FAQ. If you suspect a malfunction or require adjustment, return the
unit to us with an accurate description of the problem. Please be sure your
problem is not caused by improper operating procedure or malfunctions in your
other equipment. Send all equipment carefully packaged and insured to our
address above.

An estimate of repair cost on out-of-warranty merchandise may be forwarded if
you desire.

Normal repair time is 10 – 15 days. Paying by check will delay the repair until
the check clears (up to 15 days). For expedited service, contact our Service
Department.

Summary:

Ship via UPS, Parcel Post, or other carrier, insured.
Give a clear, detailed description of the problem.
Give your mailing address and daytime phone number, fax #, and/or email.
For warranty repairs include a copy of the receipt.

Note: Please do not e-mail your credit card information.

Limited Warranty

Quantum products have a 1 year limited warranty. Please refer to the Limited
Warranty card for complete details, conditions, and terms.

Quantum Instruments Inc.

10 Commerce Drive, Hauppauge NY 11788-3968 USA

Tel: [phone] Fax: [phone]

www.qtm.com

P7xx