Page 1
STRATOS S810 Series
S810-X52L
Ultra Dense High Computing
Multi-node 2U Server
User's Guide
Document Version: 1.2.0
Page 2
CONVENTIONS
XVI
Conventions
Several different typographic conventions are used throughout
this manual. Refer to the following examples for common
usage.
Bold type face denotes menu items, buttons and application
names.
Italic type face denotes references to other sections, and the
names of the folders, menus, programs, and files.
<Enter> type face denotes keyboard keys.
WARNING!
Warning information appears before the text it references and
should not be ignored as the content may prevent damage to the
device.
CAUTION!
CAUTIONS APPEAR BEFORE THE TEXT IT REFERENCES, SIMILAR TO
NOTES AND WARNINGS. CAUTIONS, HOWEVER, APPEAR IN CAPITAL LET-
TERS AND CONTAIN VITAL HEALTH AND SAFETY INFORMATION.
Important:
Indicates information that is important to know for the proper completion of a procedure, choice of an option, or completing a task.
!
!
Note:
Highlights general or useful information and tips.
Page 3
ACRONYMS
XVII
Acronyms
TERM DEFINITION
A/D Analog to Digital
ACPI Advanced Configuration and Power Interface
ASF Alerting Standard Forum
Asserted
Active-high (positive true) signals are asserted when in
the high electrical state (near power potential). Activelow (negative true) signals are asserted when in the low
electrical state (near ground potential).
BIOS Basic Input/Output System
BIST Built-In Self Test
BMC
At the heart of the IPMI architecture is a microcontroller
called the Baseboard management controller (BMC)
Bridge
Circuitry connecting one computer bus to another, allowing an agent on one to access the other
BSP Bootstrap processor
Byte 8-bit quantity
CLI Command Line Interface
CMOS
In terms of this specification, this describes the PC-AT
compatible region of battery-backed 128 bytes of memory, which normally resides on the baseboard
CPU Central Processing Unit
Deasserted
A signal is deasserted when in the inactive state. Activelow signal names have “_L” appended to the end of the
signal mnemonic. Active-high signal names have no “_L”
suffix. To reduce confusion when referring to active-high
and active-low signals, the terms one/zero, high/low, and
true/false are not used when describing signal states.
DTC Data Transfer Controller
EEPROM Electrically Erasable Programmable Read-Only Memory
EMP Emergency Management Port
FRU Field Replaceable Unit
GB 1024 MB.
GPIO General Purpose Input/Out
HSC Hot-Swap Controller
Hz Hertz (1 cycle/second)
I
2
C
Inter-Integrated Circuit bus
IANA Internet Assigned Numbers Authority
IBF Input buffer
ICH I/O Controller Hub
ICMB Intelligent Chassis Management Bus
IERR Internal Error
IP Internet Protocol
IPMB Intelligent Platform Management Bus
Page 4
ACRONYMS
XVIII
IPMI Intelligent Platform Management Interface
ITP In-Target Probe
KB 1024 bytes.
KCS Keyboard Controller Style
KVM Keyboard, Video, Mouse
LAN Local Area Network
LCD Liquid Crystal Display
LCT Lower Critical Threshold
LED Light Emitting Diode
LNCT Lower Non-Critical Threshold
LNRT Lower Non-Recoverable Threshold
LPC Low Pin Count
LSI Large Scale Integration
LUN Logical Unit Number
MAC Media Access Control
MB 1024 KB
MD2 Message Digest 2 – Hashing Algorithm
MD5 Message Digest 5 – Hashing Algorithm – Higher Security
Ms Milliseconds
Mux Multiplexer
NIC Network Interface Card
NMI Nonmaskable Interrupt
NM Node Management
OBF Output buffer
OEM Original Equipment Manufacturer
Ohm Unit of electrical resistance
PDB Power Distribution Board
PEF Platform Event Filtering
PEP Platform Event Paging
PERR Parity Error
POH Power-On Hours
POST Power-On Self Test
PWM Pulse Width Modulation
RAC Remote Access Card
RAM Random Access Memory
RMCP Remote Management Control Protocol
ROM Read Only Memory
RTC
Real-Time Clock. Component of the chipset on the baseboard.
RTOS Real Time Operation System
SCI Serial Communication Interface
SDC SCSI Daughter Card
SDR Sensor Data Record
SEEPROM
Serial Electrically Erasable Programmable Read-Only
Memory
Page 5
ACRONYMS
XIX
SEL System Event Log
SERR System Error
SMBus
A two-wire interface based on the I
2
C protocol. The
SMBus is a low-speed bus that provides positive
addressing for devices, as well as bus arbitration
SMI
Server Management Interrupt. SMI is the highest priority
nonmaskable interrupt
SMM Server Management Mode
SMS Server Management Software
SNMP Simple Network Management Protocol
SOL Serial Over LAN
UART Universal Asynchronous Receiver/Transmitter
UCT Upper Critical Threshold
UDP User Datagram Protocol
UNCT Upper Non-Critical Threshold
UNRT Upper Non-Recoverable Threshold
WDT Watchdog Timer
Word 16-bit quantity
Page 6
SAFETY INFORMATION
XX
Safety Information
Important Safety Instructions
Read all caution and safety statements in this document before
performing any of the instructions.
Warnings
Heed safety instructions: Before working with the server,
whether using this manual or any other resource as a reference, pay close attention to the safety instructions. Adhere to
the assembly instructions in this manual to ensure and maintain
compliance with existing product certifications and approvals.
Use only the described, regulated components specified in this
manual. Use of other products / components will void the UL
listing and other regulatory approvals of the product and will
most likely result in non-compliance with product regulations in
the region(s) in which the product is sold.
System power on/off: The power button DOES NOT turn off
the system AC power. To remove power from system, you must
unplug the AC power cord from the wall outlet. Make sure the
AC power cord is unplugged before opening the chassis, adding, or removing any components.
Hazardous conditions, devices and cables: Hazardous electrical conditions may be present on power, telephone, and communication cables. Turn off the server and disconnect the
power cord, telecommunications systems, networks, and
modems attached to the server before opening it. Otherwise,
personal injury or equipment damage can result.
Electrostatic discharge (ESD) and ESD protection: ESD can
damage drives, boards, and other parts. We recommend that
you perform all procedures in this chapter only at an ESD workstation. If one is not available, provide some ESD protection by
wearing an antistatic wrist strap attached to chassis ground any
unpainted metal surface on the server when handling parts.
ESD and handling boards: Always handle boards carefully.
They can be extremely sensitive to electrostatic discharge
(ESD). Hold boards only by their edges. After removing a board
from its protective wrapper or from the server, place the board
component side up on a grounded, static free surface. Use a
conductive foam pad if available but not the board wrapper. Do
not slide board over any surface.
Installing or removing jumpers: A jumper is a small plastic
encased conductor that slips over two jumper pins. Some jumpers have a small tab on top that can be gripped with fingertips
or with a pair of fine needle nosed pliers. If the jumpers do not
have such a tab, take care when using needle nosed pliers to
remove or install a jumper; grip the narrow sides of the jumper
with the pliers, never the wide sides. Gripping the wide sides
can damage the contacts inside the jumper, causing intermittent
problems with the function controlled by that jumper. Take care
to grip with, but not squeeze, the pliers or other tool used to
remove a jumper, or the pins on the board may bend or break.
Page 7
SAFETY INFORMATION
XXI
Page 8
REVISION HISTORY
XXII
Revision History
Refer to the table below for the updates made to this manual.
Copyright
Copyright © 2014 Quanta Computer Inc. This publication,
including all photographs, illustrations and software, is protected under international copyright laws, with all rights
reserved. Neither this manual, nor any of the material contained
herein, may be reproduced without the express written consent
of the manufacturer. All trademarks and logos are copyrights of
their respective owners.
Version 1.2 / 1/24/14
Disclaimer
The information in this document is subject to change without
notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for
any particular purpose. Furthermore, the manufacturer reserves
the right to revise this publication and to make changes from
time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.
For the latest information and updates please refer to
www.QuantaQCT.com
All the illustrations in this technical guide are for reference only
and are subject to change without prior notice.
DATE CHAPTER UPDATES
Page 9
About the Server
Chapter 1
Page 10
ABOUT THE SERVER INTRODUCTION
1-1
1.1 Introduction
This manual is written for system technicians who are responsible for troubleshooting, upgrading, and repairing the server chassis.
This document provides an overview of the hardware features of the chassis, troubleshooting information, and instructions on how to
add and replace components of the multi-node server series.The document also provides information on the BIOS, and Baseboard
Management Controller (BMC).
For the latest version of this manual, see www.quantaqct.com.
System Features
The system comprises a 2U/30.5” long chassis using a standard SSI mainboard. Some of the major features are as follows:
Chipset: Intel
®
C600 series, upgradable ROM kit support.
Processors (x2): Intel
®
Xeon E5-2600/E5-2600 v2 series
processors.
PCI-E x16: (1) PCI-E x16 G3 riser slot for low-profile card,
(1) PCI-E x16 G3 slot for Quanta LSISAS/RAID or 10 GbE
SFP+ Mezzanine card.
Memory: Up to sixteen DIMM slots are available. DDR3
800/1066/1333/1600 MHz UDIMM, RDIMM, and LRDIMM
memory is supported.
Storage: Up to six 2.5" SATA/SAS hot-plug HDDs or three
3.5" SATA/SAS hot-plug HDDs per node
Network: Intel® Powerville I350 GbE or Twinville X540
10G BASE-T RJ45 dual-port on board
Note:
S810-X52L supports power in the range of 220V - 240V.
Page 11
ABOUT THE SERVER SYSTEM FEATURES
1-2
Table 1-1: S810-X52L SKU
S810-X52L
S810-X52L 2.5"
( 1
TO 1 1G SKU)
S810-X52L 2.5"
( 1 TO 1 10G SKU)
S810-X52L 3.5"
( 1 TO 1 1G SKU)
S810-X52L 3.5"
( 1 TO 1 10G SKU)
Form Factor ( L x W x H )
X5 (2U chassis)
774.7mm x 447mm x 87.3mm
30.5" x 17.6" x 3.44"
MB size (W x L )
165mm x 492.3mm
6.5" x 19.38" (half-width)
Up to 4 independent nodes in a 2U chassis
Processor
(2) Intel
®
Xeon® processor E5-2600/E5-2600 v2 family per node, up to 130W
Chipset
Intel
®
C602 (Patsburg A)
SAS Controller
[Intel
®
SAS controller]
Intel
®
C602 (Patsburg A) upgrade ROM #5 (optional)
Intel
®
C602 (Patsburg A) upgrade ROM #6 (optional)
or
[LSI SAS controller]
Quanta LSISAS 2008 Mezzanine card (optional)
Quanta LSISAS 2108 Mezzanine card (optional)
[Intel® SAS controller]
Intel® C602 (Patsburg A) upgrade ROM #1 (optional)
Intel® C602 (Patsburg A) upgrade ROM #2 (optional)
or
[LSI SAS controller]
Quanta LSISAS 2008 Mezzanine card (optional)
Quanta LSISAS 2108 Mezzanine card (optional)
Memory
DDR3 800/1066/1333/1600 MHz x 16
ECC UDIMM/RDIMM/LRDIMM slots per node, up to 512 GB
Storage
2.5" SATA/SAS (6* 3Gb SCU) hot-plug HDD per node x 6
USB Flash Module for OS installation per node x 1
(optional)
3.5" SATA/SAS(3* 3Gb SCU) hot-plug HDD per node x 3
USB Flash Module for OS installation per node x 1
(optional)
HDD Backplane 1 to 1
PCIe Expansion Slot
PCIe x16 G3 riser slot for low-profile card per node x 1
PCIe x16 G3 slot for Quanta LSISAS/RAID or 10GbE SFP+ mezzanine card per node x 1
Page 12
ABOUT THE SERVER SYSTEM FEATURES
1-3
SW RAID Options
[Intel
®
SW RAID] (Optional)
Intel
®
C602 (Patsburg A) upgrade ROM #9 SATA RAID
0/1/10/5 for SCU
Intel
®
C602 (Patsburg A) upgrade ROM #5 SAS RAID 0/
1/10 for SCU
Intel
®
C602 (Patsburg A) upgrade ROM #6 SAS RAID 0/
1/10/5 for SCU
or
[LSI SW RAID]
Quanta LSISAS 2008 mezzanine card for RAID 0/1/10
[Intel
®
SW RAID]
Intel
®
C602 (Patsburg A) RSTe SATA RAID 0/1/10/5
Intel
®
C602 (Patsburg A) upgrade ROM #1 SAS RAID 0/
1/10 for SCU
Intel
®
C602 (Patsburg A) upgrade ROM #2 SAS RAID 0/
1/10/5 for SCU
or
[LSI SW RAID]
Quanta LSISAS 2008 mezzanine card for RAID 0/1/10
HW RAID Options
Quanta LSISAS2108 PD-8 mezzanine card for RAID 0/1/10/5 (optional)
Quanta LSISAS2108 PD-8 mezzanine card + LSI RAID 6 Key for RAID 0/1/10/5/6/50/60 (optional)
Network
(2) Intel
®
Powerville I350
GbE RJ45 ports on board
per node
(1) Quanta 10Gb SFP+
dual port mezzanine card
(optional)
(2) Intel
®
Twinville X540
10G BASE-T RJ45 ports
on board per node
(1) Quanta 10Gb SFP+
dual port mezzanine card
(optional)
(2) Intel
®
Powerville I350
GbE RJ45 ports on board
per node
(1) Quanta 10Gb SFP+
dual port mezzanine card
(optional)
(2) Intel
®
Twinville X540
10G BASE-T RJ45 ports
on board per node
(1) Quanta 10Gb SFP+
dual port mezzanine card
(optional)
Management Port (1) Dedicated 10/100 BASE-T RJ45 management port per node
Integrated Graphics BMC Aspeed AST2300 8MB DDR3 Video memory
Rear I/O
(2) USB 2.0 ports per node
(1) VGA per node
(1) RS232 Serial port per node
(2) GbE or 10G BASE-T RJ45 ports per node
(1) 10/100 BASE-T RJ45 management port per node
Table 1-1: S810-X52L SKU (Continued)
S810-X52L
S810-X52L 2.5"
( 1
TO 1 1G SKU)
S810-X52L 2.5"
( 1 TO 1 10G SKU)
S810-X52L 3.5"
( 1 TO 1 1G SKU)
S810-X52L 3.5"
( 1 TO 1 10G SKU)
Page 13
ABOUT THE SERVER SYSTEM FEATURES
1-4
Power Supply
(1) 1400W high efficiency PSU, 200-240VAC 50/60Hz
(1) 1400W high efficiency redundant PSU, 200-240VAC 50/60Hz (optional)
TPM No
RoHS Yes
Intel Node Management
support
No
System Management IPMI v2.0 Compliant, on board "KVM over IP" support
Table 1-1: S810-X52L SKU (Continued)
S810-X52L
S810-X52L 2.5"
( 1
TO 1 1G SKU)
S810-X52L 2.5"
( 1 TO 1 10G SKU)
S810-X52L 3.5"
( 1 TO 1 1G SKU)
S810-X52L 3.5"
( 1 TO 1 10G SKU)
Page 14
ABOUT THE SERVER PACKAGE CONTENTS
1-5
1.1 Package Contents
The following list includes the package components for a 2
node configuration:
1 x 2U server chassis
2 x Mainboard modules
2 x Dummy modules
4 x Processor heatsinks
16 x Dummy DIMMs
1 x Power supply
1 x Power cord
Utility CD (Technical Guide included)
Rail kit
Important:
Server configurations may vary. Confirm your sales representative
for the exact items included in your order.
Page 15
ABOUT THE SERVER A TOUR OF THE SYSTEM
1-6
1.1 A Tour of the System
The S810-X52L is available as a 2.5” HDD or a 3.5” HDD system. The following illustrations show the major component parts of
these two variants.
2.5” HDD System
Figure 1-1. 2.5” System Component Overview
1
2
3
4
5
6
7
8
9
Ta ble 1-2: 2.5” System Component Overview
No. Item Description
1 PSUs 2 Power supply units (PSU)
2 Chassis System chassis
3
Node
controller
Controls and LEDs for system management
4 2.5” HDDs 24 2.5” hard disk drive (HDD) cage
5 Fans Fan module cage
6 PDB boards Top and Bottom PDB (Power Distribution Board)
7
Top cover
extension
Top cover extension
8 Top cover System top cover with handle
9 MB modules 4 hot-swap mainboard modules
Page 16
ABOUT THE SERVER 3.5” HDD SYSTEM
1-7
3.5” HDD System
Figure 1-2. 3.5” System Component Description
1
2
3
4
5
6
7
8
Ta ble 1-3: 3.5” System Component Description
No. Item Description
1 PSUs 2 Power supply units (PSU)
2 Chassis System chassis
3
Node
controller
Controls and LEDs for system management
4 3.5” HDDs 12 3.5” hard disk drive (HDD) cage
5 Fans Fan module cage
6 PDB boards Top and Bottom PDB (Power Distribution Board)
7 Top cover System top cover with handle
8 MB modules 4 hot-swap mainboard modules
Page 17
ABOUT THE SERVER SYSTEM FRONT FEATURES
1-8
System Front Features
Figure 1-3. System Front Features
Node Control Panels
The node control panels manage specific 2.5” and 3.5” HDD
groups as indicated in the following illustrations.
2.5” HDD Group Configuration
Figure 1-4. 2.5” HDD Configuration
3.5” HDD Group Configuration
Figure 1-5. 3.5” HDD Configuration
Note:
2.5" SKU shown (Figure 1-3)
Table 1-4: System Front Features
No Feature Description
1
Node
control
panels
4 node control system
2 HDD bays 2.5” or 3.5” HDD array
2
1
Note:
Each HDD drive group serves a designated mainboard. See “System Rear Features” on page 11 for information on mainboards.
1 2 3 4
MB1 HDD BAY MB2 HDD BAY
MB3 HDD BAY
MB4 HDD BAY
Page 18
ABOUT THE SERVER SYSTEM FRONT FEATURES
1-9
Node Control Panel Features
Figure 1-6. Node Control Panel Features
Table 1-5: Node Control Panel Features
No Feature Function
1
MB1 Power
Button
Power on/off for MB1
2
MB1 ID
Button
MB1 module ID LED control
1 2 3 4
5
6
7
8
1
2
3
4
MB1 HDD BAY MB2 HDD BAY
MB3 HDD BAY
MB4 HDD BAY
3
MB2 Power
Button
Power On/Off for MB2
4
MB2 ID
Button
MB2 module ID LED control
5
MB3 Power
Button
Power on/off for MB3
6
MB3 ID
Button
MB3 module ID LED control
7
MB4 Power
Button
Power on/off for MB4
8
MB4 ID
Button
MB4 module ID LED control
Note:
The buttons are functional LEDs. The numbered items in the following tables represent the same item in the preceding figure.
Table 1-5: Node Control Panel Features (Continued)
No Feature Function
Page 19
ABOUT THE SERVER SYSTEM HDD SKU INTRODUCTION
1-10
System HDD SKU Introduction
The multi-node systems are available as a 2.5” or 3.5” SKU.
Within the HDD array, the HDD enumeration is as follows:
2.5” HDD Configuration
Figure 1-7. 2.5” HDD Configuration
3.5” HDD Configuration
Figure 1-8. 3.5” HDD Configuration
Table 1-6: Node Control Panel LED Description
No Feature Function Status Description
1
MB1 Power
Button LED
Power button
LED function
Green LED:
On
DC on
3
MB2 Power
Button LED
Green LED:
Off
DC off
5
MB3 Power
Button LED
Amber LED:
Blinking
DC off and
fault
7
MB4 Power
Button LED
Green LED/
Amber LED:
alternate
blinking
DC on and
fault
2
MB1 ID
Button
ID button LED
function
Blue LED:
Blinking
Select mode
4
MB2 ID
Button
6
MB3 ID
Button
Blue LED: Off
Normal
mode
8
MB4 ID
Button
Note:
The numbered items in “Node Control Panel LED Description” are
a direct correlation to “Node Control Panel Features”.
0 1 2 3 4 5 012345
MB1 HDD BAY MB2 HDD BAY
MB3 HDD BAY
MB4 HDD BAY
012345 012345
MB1 HDD BAY MB2 HDD BAY
MB3 HDD BAY
MB4 HDD BAY
0
1
2
0
1
2
0
1
2
0
1
2
Page 20
ABOUT THE SERVER SYSTEM REAR FEATURES
1-11
System Rear Features
S810-X52L System Rear
Figure 1-9. S810-X52L System Rear
The S810-X52L system rear consists of four mainboard modules and two power supply units. Dummy modules are installed
to maintain proper airflow in the event that mainboard slots are
not fully populated.
S810-X52L Module I/O Features
Figure 1-10. S810-X52L Module I/O Features
WARNING!
Mainboard combinations other than S810-X52L are
not supported.
!
TOP PSU
BOTTOM PSU
MB 1
MB 2
MB 3
MB 4
Table 1-7: S810-X52L Module I/O Features
No Feature Description
1 USB port 2 USB ports (2.0 compliant)
2 Rear ID LED ID identification
3 Serial port Connect serial devices to this port
4 VGA port Connect a monitor to this port
5
Dedicated
Management
Port
10/100 BASE-T RJ45 management port
6 NIC 2 GbE or 10G BASE-T RJ45 port
7 NIC 1 GbE or 10G BASE-T RJ45 port
8 Power button On/Off power to the module
1 23 4 5 678
Page 21
ABOUT THE SERVER SYSTEM REAR FEATURES
1-12
S810-X52L Module I/O LED Description
Ta ble 1-8: S810 -X52L Module I/O LED Description
No Feature Status Description
2ID LED
Blue On
Identify module by
BMC Web UI
Blue
Blinking
Identify module by
PWR button
Off Normal mode
5,6
NIC1 & 2
LEDs (see
“LAN LEDs”)
Right
Off No link
Green On Link, no access
Green
Blinking
Link, access
Left
Off
No link / link, access
10 Mbps
Green On Link, access 100 Mbps
Amber On
Link, access 1000
Mbps
7
Remote
Management
port LEDs
Right
Off No link, no access
Green Off Link, no access
Amber On Link, no access
Green On Link, access 10 Mbps
Amber On Link, access 100 Mbps
Left
Off
No link / link, no
access
Green
Blinking
Link, access
Table 1-8: S810-X52L Module I/O LED Description (Continued)
No Feature Status Description
Page 22
ABOUT THE SERVER SYSTEM REAR FEATURES
1-13
LAN LEDs
The system mainboard has one I350 or X540 (optional) Ethernet controller and two 1GbE or 10GbE (optional) ports. Each
RJ45 connector has two built-in LEDs. See the following illustration and table for details.
Figure 1-11. RJ45 LAN Connector
HDD LED
Table 1-9: 1 GbE and 10 GbE LED Description
10 GbE Chip Onboard 1 GbE Chip Onboard
Link Activity Link Activity
10 GbE LED Green
Green
Blinking
N/A N/A
1 GbE LED Amber
Green
Blinking
Amber
Green Blinking
100M Off
Green
Blinking
Green
Green Blinking
Link
Activity
PIN 1
Location
Table 1-10: HDD LED Description
SGPIO LED Pattern
Slot/Device States (RAID States) HDD Access
Identification
Status
LED
(Green)
Status
LED
(Amber)
Fault LED
(Red)
Active LED (Deep
Green)
Slot Empty n/a Off Off Off
Identify n/a On Off
When HDD R/W
access, the
active LED is On.
No R/W access,
the active LED is
Off.
Active LED con-
trol by HDD.
When rebuild
completed Identify/Fault, Status/
Fault LED will
return to green.
Fail n/a Off On
Rebuild n/a
On 1 sec./
Off 1 sec.
Off 1 sec./
On 1 sec.
Device Online On n/a Off
Page 23
ABOUT THE SERVER POWER SUB-SYSTEM
1-14
Power Sub-System
Figure 1-12. PSU to Mainboard Module Description
A system has two modular Power Supply Units (PSU). Both
PSU’s are directly connected to the Power Distribution Boards
(PDBs), the HDD backplane, and middle plane allowing each
PSU to individually provide power for all mainboards (MB1 to
MB4).
The power supply units used for each model are:
PSU LED
Figure 1-13. PSU LED
WARNING!
Mainboard combinations other than S810-X52L are
not supported.
Table 1-11: Power Supply Units by Model
Model PSU AC Input
S810-X52L 2 x 1400W redundant PSU 220V
TOP PSU
BOTTOM PSU
MB 1
MB 2
MB 3
MB 4
!
Table 1-12: PSU LED Description
No Feature Status Description
1PSU LED
Green Normal operation
Yellow Fault
1
Page 24
ABOUT THE SERVER COOLING SUB-SYSTEM
1-15
Cooling Sub-System
Fans may spin for some time after the system has been powered off. Allow time for the fans to stop rotating before handling
system components.
Figure 1-14. Cooling Sub System
Table 1-13: Fan Cooling System
No Feature Description
1
Fan cooling
system
A metal frame holding fan modules
1
Page 25
Installation and Assembly Safety
Instructions
Chapter
Installation and Assembly Safety
Instructions
Chapter
Page 26
INSTALLATION AND ASSEMBLY SAFETY INSTRUCTIONS INSTALLATION ASSEMBLY SAFETY INSTRUCTIONS
2-1
2.1 Installation Assembly Safety Instructions
Guidelines
The power supply in this product contains no user-serviceable parts.
Refer servicing only to qualified personnel.
Do not attempt to modify or use the supplied AC power cord if it is not the exact type required. A product
with more than one power supply will have a separate AC power cord for each supply.
The power button on the system does not turn off system AC power.
To remove AC power from the system, you must unplug each AC power cord from the wall outlet or power
supply.
The power cord(s) is considered the disconnect device to the main (AC) power. The socket outlet that the
system plugs into shall be installed near the equipment and shall be easily accessible.
Page 27
INSTALLATION AND ASSEMBLY SAFETY INSTRUCTIONS GUIDELINES
2-2
SAFETY STEPS: Whenever you remove the chassis covers to access the inside of the system, follow these
steps:
1. Turn off all peripheral devices connected to the system.
2. Turn off the system by pressing the power button.
3. Unplug all AC power cords from the system or from wall outlets.
4. Label and disconnect all cables connected to I/O connectors or ports on the back of the system.
5. Provide some electrostatic discharge (ESD) protection by wearing an antistatic wrist strap attached to
chassis ground of the system-any unpainted metal surface-when handling components.
6. Do not operate the system with the chassis covers removed.
A microprocessor and heat sink may be hot if the system has been running. Also, there may be sharp pins
and edges on some board and chassis parts. Contact should be made with care. Consider wearing protective gloves.
Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Dispose of used batteries according to manufacturer's instructions.
Page 28
INSTALLATION AND ASSEMBLY SAFETY INSTRUCTIONS GUIDELINES
2-3
The system is designed to operate in a typical office environment.
Choose a site that is:
Clean and free of airborne particles (other than normal room dust).
Well ventilated and away from sources of heat including direct sunlight.
Away from sources of vibration or physical shock.
Isolated from strong electromagnetic fields produced by electrical devices.
In regions that are susceptible to electrical storms, we recommend you plug your system into a surge
suppressor and disconnect telecommunication lines to your modem during an electrical storm.
Provided with a properly grounded wall outlet.
Provided with sufficient space to access the power supply cord(s), because they serve as the product's
main power disconnect.
WARNING!
The server system is safety certified as rack-mounted equipment for use in a server room or computer room,
using the customer rack kit.
The rail racks are designed to carry only the weight of the server system. Do not place additional load onto
any rail-mounted equipment.
System rack kits are intended to be installed in a rack by trained service technicians.
Heavy object. Indicates two people are required to safely handle the system.
Page 29
Safety Information
Chapter
Safety Information
Chapter
Page 30
SAFETY INFORMATION SERVER SAFETY INFORMATION
3-1
3.1 Server Safety Information
To reduce the risk of bodily injury, electrical shock, fire, and
equipment damage, read this document and observe all warnings and precautions in this guide before installing or maintaining your server product.
In the event of a conflict between the information in this document and information provided with the product or on the website for a particular product, the product documentation takes
precedence.
Your server should be integrated and serviced only by technically qualified persons.
You must adhere to the guidelines in this guide and the assembly instructions in your server manuals to ensure and maintain
compliance with existing product certifications and approvals.
Use only the described, regulated components specified in this
guide. Use of other products / components will void the UL Listing and other regulatory approvals of the product, and may
result in noncompliance with product regulations in the
region(s) in which the product is sold.
Safety Warnings and Cautions
To avoid personal injury or property damage, before you begin
installing the product, read, observe, and adhere to all of the following safety instructions and information. The following safety
symbols may be used throughout the documentation and may
be marked on the product and / or the product packaging.
CAUTION
Indicates the presence of a hazard that may cause
minor personal injury or property damage if the
CAUTION is ignored.
WARNING
Indicates the presence of a hazard that may result
in serious personal injury if the WARNING is
ignored.
Indicates potential hazard if indicated information is
ignored.
Indicates shock hazards that result in serious injury
or death if safety instructions are not followed.
Indicates hot components or surfaces.
Indicates do not touch fan blades, may result in
injury.
Indicates to unplug all AC power cord(s) to disconnect AC power.
Page 31
SAFETY INFORMATION INTENDED APPLICATION USES
3-2
Intended Application Uses
This product was evaluated as Information Technology Equipment (ITE), which may be installed in offices, schools, computer
rooms, and similar commercial type locations. The suitability of
this product for other product categories and environments
(such as medical, industrial, residential, alarm systems, and
test equipment), other than an ITE application, may require further evaluation.
Site Selection
The system is designed to operate in a typical office environment. Choose a site that is:
Clean, dry, and free of airborne particles (other than nor-
mal room dust).
Well-ventilated and away from sources of heat including
direct sunlight and radiators.
Away from sources of vibration or physical shock.
Isolated from strong electromagnetic fields produced by
electrical devices.
In regions that are susceptible to electrical storms, we rec-
ommend you plug your system into a surge suppressor
and disconnect telecommunication lines to your modem
during an electrical storm.
Provided with a properly grounded wall outlet.
Provided with sufficient space to access the power supply
cord(s), because they serve as the product's main power
disconnect.
Provided with either two independent AC power sources
or two independent phases from a s single source.
Please recycle battery.
The rail racks are designed to carry only the weight
of the server system. Do not use rail-mounted
equipment as a workspace. Do not place additional
load onto any rail-mounted equipment.
Indicates two people are required to safely handle
the system.
Restricted Access Location: The server is
intended for installation only in a Server Room or
Computer Room where both these conditions
apply:
access can only be gained by SERVICE PER-
SONS or by USERS who have been instructed
about the reasons for the restrictions applied to
the location and about any precautions that shall
be taken; and
access is through the use of a TOOL or lock and
key, or other means of security, and is controlled
by the authority responsible for the location.
Page 32
SAFETY INFORMATION EQUIPMENT HANDLING PRACTICES
3-3
Equipment Handling Practices
Reduce the risk of personal injury or equipment damage:
Conform to local occupational health and safety require-
ments when moving and lifting equipment.
Use mechanical assistance or other suitable assistance
when moving and lifting equipment.
To reduce the weight for easier handling, remove any eas-
ily detachable components.
Power and Electrical Warnings
Power Cord Warnings
If an AC power cord was not provided with your product, purchase one that is approved for use in your country.
CAUTION!
THE POWER BUTTON, INDICATED BY THE STAND-BY POWER MARKING,
DOES NOT
COMPLETELY TURN OFF THE SYSTEM AC POWER, 5V
STANDBY POWER IS ACTIVE WHENEVER THE SYSTEM IS PLUGGED IN.
T
O REMOVE POWER FROM SYSTEM, YOU MUST UNPLUG THE AC
POWER CORD FROM THE WALL OUTLET. YOUR SYSTEM MAY USE MORE
THAN ONE AC POWER CORD. MAKE SURE ALL AC POWER CORDS ARE
UNPLUGGED. MAKE SURE THE AC POWER CORD(S) IS / ARE
UNPLUGGED BEFORE YOU OPEN THE CHASSIS, OR ADD OR REMOVE
ANY NON HOT-PLUG COMPONENTS.
CAUTION!
DO NOT ATTEMPT TO MODIFY OR USE AN AC POWER CORD IF IT IS NOT
THE EXACT TYPE REQUIRED. A SEPARATE AC CORD IS REQUIRED FOR
EACH SYSTEM POWER SUPPLY.
!
!
CAUTION!
THE POWER SUPPLY IN THIS PRODUCT CONTAINS NO USER-SERVICE-
ABLE PARTS. DO NOT OPEN THE POWER SUPPLY. HAZARDOUS VOLT-
AGE, CURRENT AND ENERGY LEVELS ARE PRESENT INSIDE THE POWER
SUPPLY. RETURN TO MANUFACTURER FOR SERVICING.
CAUTION!
WHEN REPLACING A HOT-PLUG POWER SUPPLY, UNPLUG THE POWER
CORD TO THE POWER SUPPLY BEING REPLACED BEFORE REMOVING IT
FROM THE SERVER.
CAUTION!
TO AVOID RISK OF ELECTRIC SHOCK, TURN OFF THE SERVER AND DIS-
CONNECT THE POWER CORD, TELECOMMUNICATIONS SYSTEMS, NET-
WORKS, AND MODEMS ATTACHED TO THE SERVER BEFORE OPENING IT.
CAUTION!
TO AVOID ELECTRICAL SHOCK OR FIRE, CHECK THE POWER CORD(S)
THAT WILL BE USED WITH THE PRODUCT AS FOLLOWS:
Do not attempt to modify or use the AC power cord(s) if they
are not the exact type required to fit into the grounded electrical
outlets.
The power cord(s) must meet the following criteria: The power
cord must have an electrical rating that is greater than that of
the electrical current rating marked on the product.
!
!
!
!
Page 33
SAFETY INFORMATION SYSTEM ACCESS WARNINGS
3-4
System Access Warnings
CAUTION!
THE POWER CORD MUST HAVE SAFETY GROUND PIN OR CONTACT
THAT IS SUITABLE FOR THE ELECTRICAL OUTLET.
CAUTION!
THE POWER SUPPLY CORD(S) IS / ARE THE MAIN DISCONNECT DEVICE
TO AC POWER. THE SOCKET OUTLET(S) MUST BE NEAR THE EQUIP-
MENT AND READILY ACCESSIBLE FOR DISCONNECTION.
CAUTION!
THE POWER SUPPLY CORD(S) MUST BE PLUGGED INTO SOCKET-OUT-
LET(S) THAT IS /ARE PROVIDED WITH A SUITABLE EARTH GROUND.
!
!
!
CAUTION!
TO AVOID PERSONAL INJURY OR PROPERTY DAMAGE, THE FOLLOWING
SAFETY INSTRUCTIONS APPLY WHENEVER ACCESSING THE INSIDE OF
THE PRODUCT:
Turn off all peripheral devices connected to this product.
Turn off the system by pressing the power button to off.
Disconnect the AC power by unplugging all AC power cords
from the system or wall outlet.
Disconnect all cables and telecommunication lines that are
connected to the system.
Retain all screws or other fasteners when removing access
cover(s). Upon completion of accessing inside the product,
refasten access cover with original screws or fasteners.
Do not access the inside of the power supply. There are no ser-
viceable parts in the power supply. Return to manufacturer for
servicing.
Power down the server and disconnect all power cords before
adding or replacing any non hot-plug component.
When replacing a hot-plug power supply, unplug the power
cord to the power supply being replaced before removing the
power supply from the server.
CAUTION!
IF THE SERVER HAS BEEN RUNNING, ANY INSTALLED PROCESSOR(S)
AND HEAT SINK(S) MAY BE HOT.
!
!
Page 34
SAFETY INFORMATION RACK MOUNT WARNINGS
3-5
Rack Mount Warnings
The following installation guidelines are required by UL for
maintaining safety compliance when installing your system into
a rack.
The equipment rack must be anchored to an unmovable support to prevent it from tipping when a server or piece of equipment is extended from it. The equipment rack must be installed
according to the rack manufacturer's instructions.
Install equipment in the rack from the bottom up, with the heaviest equipment at the bottom of the rack.
Extend only one piece of equipment from the rack at a time.
You are responsible for installing a main power disconnect for
the entire rack unit. This main disconnect must be readily
accessible, and it must be labeled as controlling power to the
entire unit, not just to the server(s).
To avoid risk of potential electric shock, a proper safety ground
must be implemented for the rack and each piece of equipment
installed in it.
Elevated Operating Ambient - If installed in a closed or multiunit rack assembly, the operating ambient temperature of the
rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment
in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow - Installation of the equipment in a rack
should be such that the amount of air flow required for safe
operation of the equipment is not compromised.
Mechanical Loading - Mounting of the equipment in the rack
should be such that a hazardous condition is not achieved due
to uneven mechanical loading.
Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the effect that
overloading of the circuits might have on overcurrent protection
and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.
Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained.
CAUTION!
UNLESS YOU ARE ADDING OR REMOVING A HOT-PLUG COMPONENT,
ALLOW THE SYSTEM TO COOL BEFORE OPENING THE COVERS. TO
AVOID THE POSSIBILITY OF COMING INTO CONTACT WITH HOT COMPO-
NENT(S) DURING A HOT-PLUG INSTALLATION, BE CAREFUL WHEN
REMOVING OR INSTALLING THE HOT-PLUG COMPONENT(S).
CAUTION!
TO AVOID INJURY DO NOT CONTACT MOVING FAN BLADES. IF YOUR
SYSTEM IS SUPPLIED WITH A GUARD OVER THE FAN, DO NOT OPERATE
THE SYSTEM WITHOUT THE FAN GUARD IN PLACE.
!
!
Page 35
SAFETY INFORMATION ELECTROSTATIC DISCHARGE (ESD)
3-6
Particular attention should be given to supply connections other
than direct connections to the branch circuit (e.g. use of power
strips).
Electrostatic Discharge (ESD)
Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by their edges. After removing a
board from its protective wrapper or from the server, place the
board component side up on a grounded, static free surface.
Use a conductive foam pad if available but not the board wrapper. Do not slide board over any surface.
Other Hazards
Battery Replacement
Cooling and Airflow
CAUTION!
ESD CAN DAMAGE DRIVES, BOARDS, AND OTHER PARTS. WE RECOM-
MEND THAT YOU PERFORM ALL PROCEDURES AT AN ESD WORKSTA-
TION. IF ONE IS NOT AVAILABLE, PROVIDE SOME ESD PROTECTION BY
WEARING AN ANTISTATIC WRIST STRAP ATTACHED TO CHASSIS
GROUND -- ANY UNPAINTED METAL SURFACE -- ON YOUR SERVER
WHEN HANDLING PARTS.
CAUTION!
THERE IS THE DANGER OF EXPLOSION IF THE BATTERY IS INCOR-
RECTLY REPLACED. WHEN REPLACING THE BATTERY, USE ONLY THE
BATTERY RECOMMENDED BY THE EQUIPMENT MANUFACTURER.
!
!
CAUTION!
DISPOSE OF BATTERIES ACCORDING TO LOCAL ORDINANCES AND REG-
ULATIONS.
CAUTION!
DO NOT ATTEMPT TO RECHARGE A BATTERY.
CAUTION!
DO NOT ATTEMPT TO DISASSEMBLE, PUNCTURE, OR OTHERWISE DAM-
AGE A BATTERY.
CAUTION!
CAREFULLY ROUTE CABLES AS DIRECTED TO MINIMIZE AIRFLOW
BLOCKAGE AND COOLING PROBLEMS. FOR PROPER COOLING AND AIR-
FLOW, OPERATE THE SYSTEM ONLY WITH THE CHASSIS COVERS
INSTALLED. OPERATING THE SYSTEM WITHOUT THE COVERS IN PLACE
CAN DAMAGE SYSTEM PARTS. TO INSTALL THE COVERS:
Check first to make sure you have not left loose tools or parts
inside the system.
Check that cables, add-in cards, and other components are
properly installed.
Attach the covers to the chassis according to the product
instructions.
!
!
!
!
Page 36
SAFETY INFORMATION OTHER HAZARDS
3-7
Laser Peripherals or Devices
CAUTION!
TO AVOID RISK OF RADIATION EXPOSURE AND / OR PERSONAL INJURY:
Do not open the enclosure of any laser peripheral or device
Laser peripherals or devices are not serviceable
Return to manufacturer for servicing.
Use certified and rated Laser Class I for Optical Transceiver
product.
!
Page 37
Regulatory and Compliance
Information
Chapter
Regulatory and Compliance
Information
Chapter
Page 38
REGULATORY AND COMPLIANCE INFORMATION PRODUCT REGULATORY COMPLIANCE MARKINGS
4-1
4.1 Product Regulatory Compliance Markings
This product is marked with the following Product Certification
markings:
Table 10-1: Product Regulatory Compliance Markings
R
EGULATORY
C
OMPLIANCE
REGION MARKING
cULus Listing
Marks
USA /
Canada
CE Mark Europe
FCC Marking
(Class A)
USA
This device complies with Part 15 of the
FCC Rules. Operation of this device is
subject to the following two conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
VCCI Marking (Class A)
Japan
BSMI Certification Number & Class A
Warning
Taiwan
R43039
GOST R
Marking
Russia
ICES Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la
classe A est conforme à la norme
NMB-003 du Canada.
Recycling
Package
Mark
Other than
China
Table 10-1: Product Regulatory Compliance Markings (Continued)
Page 39
REGULATORY AND COMPLIANCE INFORMATION ELECTROMAGNETIC COMPATIBILITY NOTICES
4-2
4.2 Electromagnetic Compatibility Notices
FCC Verification Statement (USA)
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one
or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the
receiver
Connect the equipment to an outlet on a circuit other than
the one to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
Any changes or modifications not expressly approved by the
grantee of this device could void the user's authority to operate
the equipment. The customer is responsible for ensuring compliance of the modified product.
Only peripherals (computer input/output devices, terminals,
printers, etc.) that comply with FCC Class A or B limits may be
attached to this computer product. Operation with noncompliant
peripherals is likely to result in interference to radio and TV
reception.
All cables used to connect to peripherals must be shielded and
grounded. Operation with cables, connected to peripherals, that
are not shielded and grounded may result in interference to
radio and TV reception.
Europe (CE Declaration of
Conformity)
This product has been tested in accordance too, and complies
with the Low Voltage Directive (73/23/EEC) and EMC Directive
(89/336/EEC). The product has been marked with the CE Mark
to illustrate its compliance.
Page 40
REGULATORY AND COMPLIANCE INFORMATION VCCI (JAPAN)
4-3
VCCI (Japan)
English translation of the notice above:
This is a Class A product based on the standard of the Voluntary Control Council for Interference (VCCI) from Information
Technology Equipment. If this is used near a radio or television
receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction
manual.
BSMI (Taiwan)
The BSMI Certification Marking and EMC warning is located on
the outside rear area of the product
Regulated Specified Components
To maintain the UL listing and compliance to other regulatory
certifications and/or declarations, the following regulated components must be used and conditions adhered to. Interchanging
or use of other component will void the UL listing and other
product certifications and approvals.
Updated product information for configurations can be found on
the site at the following URL: www.qsscit.com
If you do not have access to the Web address, please contact
your local representative.
Add-in cards: must have a printed wiring board flammabil-
ity rating of minimum UL94V-1. Add-in cards containing
external power connectors and/or lithium batteries must
be UL recognized or UL listed. Any add-in card containing
modem telecommunication circuitry must be UL listed. In
addition, the modem must have the appropriate telecommunications, safety, and EMC approvals for the region in
which it is sold.
Peripheral Storage Devices: must be UL recognized or UL
listed accessory and TUV or VDE licensed. Maximum
power rating of any one device is 19 watts. Total server
configuration is not to exceed the maximum loading conditions of the power supply.
Page 41
REGULATORY AND COMPLIANCE INFORMATION RESTRICTION OF HAZARDOUS SUBSTANCES (ROHS) COMPLIANCE
4-4
Restriction of Hazardous Substances
(RoHS) Compliance
Quanta® Computer Inc. has a system in place to restrict the
use of banned substances in accordance with the European
Directive 2002/95/EC. Compliance is based on declaration that
materials banned in the RoHS Directive are either (1) below all
applicable threshold limits or (2) an approved / pending RoHS
exemption applies.
RoHS implementation details are not fully defined and may
change.
Threshold limits and banned substances are noted below:
Quantity limit of 0.1% by mass (1000 PPM) for:
Lead
Mercury
Hexavalent Chromium
Polybrominated Biphenyls Diphenyl Ethers (PBDE)
Quantity limit of 0.01% by mass (100 PPM) for:
Cadmium
End of Life / Product Recycling
Product recycling and end-of-life take-back systems and
requirements vary by country. Contact the retailer or distributor
of this product for information about product recycling and / or
take-back.
Loading...