Qualtex MIS882, MIS883, MIS884 User Manual

User

Manual

Commercial Water Boiler

SAVE

THESE INSTRUCTIONS FOR FUTURE

REFERENCE

INTRODUCTION

This

electric catering

water urn is

manufactured

in

resilient

stainless

steel and

polished

to

give

a long

lasting

finish.

Good care

and supervision

of

your

new

purchase

will give you years

of trouble-free service.

Constant

simmering

water

enables hot drinks to

be

prepared

quickly

in

places

like

hotels,

cafes, schools,

offices,lounges,

restaurants

and all

kinds of

party

gatherings.

IMPORTANT

SAFEGUARDS

To ensure

you

obtain full

benefits from

your

new

catering

urn. Please

read

this instruction

booklet

carefully,

and follow

all instructions;

failure

to

follow

guided

instructions

responsibly

will

not

be accepted.

Installation

requirements

It is essential

that

this appliance is

installed

correctly. Installation

should comply

with electric

outlet

22O/240V.

L.

2.

Before

Using/Connecting to Power

Supply:

Remove all

packaging

and any

protective

plastic

coating.

Only use

urn

on a

flat level

surface that

is

adequate

to

support

the weight

when full

of water, and

keep

it

away

from

the

edge of

counters

to avoid

accident.

Do

not

place

the appliance

near a

hot

gas

or electric

burner

or near

any hot surfaces.

Close

supervision

is

necessary

when

any appliance

is

used by

or

near

children,

4.

Do not use the

water urn

outdoors.

If the

supply

cord

is

damaged,

it must

be

replaced

by

the manufacturer,

service

agent

or

similar

qualified

person

in order

to avoid

a

hazard.

(The

supply

cord

may

become

warm

when

the appliance

is in use')

If the

water

urn breakdowns

or

has been

damaged

in

any

manner,

return it

to

the nearest

authorized

service

facility

for

examination

and

repair.

7.

Always

switch

off

before

removing

plug from the

outlet.

8.

Do not lift

or

move the

urn when

it contains

hot water'

9.

Turn

off the

power supply

and

remove

the

plug when

not

in use.

Cool

the

water

urn

off

before

moving/cleaning

or

replacing

any

parts'

10.

Remove

the

plug

by

grasping the

plug. Do not

pull

the cord.

5.

6.

11. Do

not

let cord hang over edge

of counter/work

space.

IZ.Do not

place

the

appliance

where

the mains lead

could fall into

a sink.

L3. Place

the water

urn securely in center of counter

or

work

space.

L4. Always

put

water in the urn before switching on. Do

not switch

on the water urn if the water tank is

empty.

15. To

protect

against

electric shock, do not immerse the

water urn

in water.

16. Switch OFF after use and unplug

the unit

from the

socket.

l7.Do not overfill urn as there is a risk that boiling

water will

be ejected

from

around the lid.

18. The water urn should not be

operated by

persons

(including

children) with reduced

physical,

sensory

or mental capabilities,

or

lack

of experience or

knowledge, without

supervision.

THE

WATER

URN

Cool-touch handles

Temperafure

Control

Plastic

lid with

twist

lock

OrVOff

switch

THE APPLIANCE

IS NOW

READY TO USE

WARNING:

-

Do

not touch the

surface.

The surface of the

water

urn

gets

very

hot during use.

- Do

not remove the

lid while boiling.

- If the

appliance

is overfilled, boiling

water may spill

out.

- This appliance

is not intended

for use by

young

children unless

they

are adequately supervised

by

a

responsible

person

to ensure

that they can

use the

appliance safely.

i
I

l

I

I

.

Before

Use:

Fill,

heat, and

discard the

water twice

before

general use.

-

Under

filling

may

cause

the thermal

cut-out to

operate

[and

may

shorten

the

element life).

HOW TO USE

1. Remove all

packaging

before

use.

2.

Place

the drip

tray on

the base

underneath

the

tap,

as shown in

picture.

3. Twist lid anti

clockwise.

Open the

lid

and fill the

urn

with the

desired

amount

of

water.

Do not fill above

the MAX

capacity

mark.

4. Always

put

water

in the urn before

switching

on.

5.

Plug the

urn to the

main

socket.

6. Switch

ON the

urn. The

red indicator

light

will

illuminate

when water

is heating.

After the

water

has

boiled

the

urn will

automatically

switch to

keep

warm, and

the

green

indicator

light will

illuminate

showing

that the

urn is

preserving heat.

7.

Turn the temperature

control to

the desired

setting.

This urn

is not

intended to

continuously

boil water

due to

the hazards

of steam and

water escaping

from

under

the

lid.

B. Use the

water faucet

to dispense

water. Open the

tap

by

pulling

the

tap lever to

the horizontal

position;

close

the tap

by returning

the lever to the

vertical

position.

9.

When about

three cups of

water are

remaining in the

urn,

turn the appliance

off and

unplug it from the

electric

outlet.

ro. Always

make

sure there

is at least minimal water

in

the

urn to

prevent boil-dry.

I

BOIt-DRY

PROTECTION

To

prevent

accident

from

boil-dry, the appliance

is

protected

with

a

thermal limiter. If water in the tank

is

boiled dry, the limiter

activates and

the appliance turns

itself

off, although

the lamp will remain

on.

If

the thermal

limiter is

activated, there

is

a manual reset

button

located

in the middle of the base bottom. Turn

off unit. Let to cool.

Press button to reset.

THERMAL

CUT-OUT

The heating

element is fitted

with a thermal cut-out,

which

protects

the urn from

damage when continuous misuse

of

the

urn is allowed

[boil

dry, switched

on

without

water,

or

the appliance

exterior has

been accessible with water)

the

thermal cut-out will

stop the appliance

from working.

Do not confuse

thermal cut-out

with boil-dry

protection.

Thermal

cut-out in

the appliance is

a disposable

part.

Once

thermal cut-out is

triggered, the appliance

will be

impaired

and cannot

be used again. Therefore

the

appliance

should be taken

to an authorized agent

to

replace

the thermal

cut-out. A single fuse will

be replaced.

In rare instances, if

the heating element is

damaged, the

unit

must

be replaced.

CLEANING AND MAINTENANCE

ALWAYS TURN

OFF THE POWER

SUPPLY, REMOVE THE PLUG

AND ALLOW

THE URN TO

COOL

BEFORE

CLEANING.

THIS

URN IS NOT

WATERPROOF!

CLEANING

THE URN

- Always rinse the

urn

immediately

after each

use'

- Pour

a small

amount

of

hot

water into the tank.

Brush

sides

and

rinse

with

hot water

until clean.

- Clean interior

with

a

soft brush.

Remove

any scale

or sediment

from

the element

and

rinse thoroughly

with

clean

water.

-

Always

remember

to empty and

rinse the

urn

with

hot

water before

using

again.

-

Remove the

cover

and

clean.

-

Clean the

exterior

with water and

detergent.

Do

not

use harsh

abrasive

cleaners

to avoid

scratches'

Doing

so will

damage

the surface

finish.

-

Use a soft

cloth

to wipe the

urn body

dry.

Descaling:

In hard

water areas,

scale will

form on the

element

and

interior.

This

will adversely

affect the

operation

of the

urn

if allowed

to accumulate.

Descale

on a

regular basis,

using

a suitable

descaler

recommended

for stainless

steel

kettles.

Follow

the instructions

provided with the

descaling

product.

ELECTRIC

CIRCUIT DIAGRAM

This

appliance requires a 16Amp

plug.

USAGE PAMNIETERS:

Model No. Power

Approximate

Capacity

Voltage Environmental

Temperature
in Use

Environmental
Humidity
in Use

MISBB2 1500w 9L

220V-

240V/

50Hz

10-38 degrees Less

than 90%

MISBB3 1500w

20L

220V-

240V/

50Hz

10-38

degrees Less than 90%

MISBB4 2500w 351

220V­240V

/

50Hz

10-38 degrees Less

than

90%