Qualstar XLS-810160, XLS-810240 User Manual
XLS-810160/
810240
Tape Library
Product Specification
501800 Rev. C
Copyright Notice
Copyright© 2010 by Qualstar Corporation — All Rights Reserved
Information contained in this document is copyrighted by Qualstar Corporation. It is
intended for use by Qualstar's customers and prospective customers to evaluate,
integrate, operate and maintain Qualstar products. Customers and prospective
customers may reproduce this document as needed for these uses. Reproduction in
whole or in part for any other use or by any other party is prohibited without prior
written permission from Qualstar Corporation.
Disclaimer
Every effort has been made to keep the information contained in this document
current and accurate as of the date of publication or revision. However, no guarantee
is given or implied that the document is error-free or that it is accurate with regard to
any specification.
Qualstar reserves the right to modify the design or specification without notice. This
specification may not be construed as a contractual obligation except as specifically
agreed to by Qualstar in writing at the time of order.
Trademark Notice
Qualstar and the Qualstar logo are registered trademarks and X-Link is a trademark
of Qualstar Corporation. Other trademarks are the property of their respective
owners.
Notices
Qualstar products are covered by one or more of the following patents:
6,271,982, 6,560,061 and 7,181,313. Other patents pending.
Equipment is manufactured from new parts, or new and used parts.
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense Shielded or optical cables are required for this device to comply with
FCC Rules. Use them when connecting this device to others.
XLS-810160/810240 Library Product Specification
i
For additional information, contact Qualstar at:
QUALSTAR CORPORATION
3990-B Heritage Oak Court
Simi Valley CA 93063
Fax: (805) 583-7749
Phone: (805) 583-7744
Email: sales@qualstar.com
www.qualstar.com
ii 501800 Rev. C
Table of Contents
1 Introduction ...................................................................................................................... 1-1
1.1 Scope.............................................................................................................................. 1-1
1.2 Related Documentation................................................................................................ 1-1
2 Product Description ........................................................................................................ 2-1
2.1 General Description...................................................................................................... 2-1
2.2 XLS Standard Features ............................................................................................... 2-3
2.3 X-Link Features............................................................................................................ 2-4
2.4 XLS High Availability Features .................................................................................. 2-4
2.5 Features ........................................................................................................................ 2-5
2.6 XLS Library .................................................................................................................. 2-6
2.6.1 System Controller.................................................................................................. 2-7
2.6.2 Power Supplies ...................................................................................................... 2-7
2.6.3 Touch Screen and X-Link Interface ..................................................................... 2-9
2.6.4 Robotic Handler and Barcode Reader................................................................ 2-10
2.6.5 Tape Drives.......................................................................................................... 2-11
2.6.6 I/O Port................................................................................................................. 2-11
2.6.7 Cartridge Slots..................................................................................................... 2-11
2.6.8 Doors, Windows, Locks, and Security Features ................................................ 2-12
2.6.9 Expansion Pod ..................................................................................................... 2-12
2.6.10 XLS-85000 Memory Expansion Module............................................................. 2-13
3 Physical Specifications................................................................................................... 3-1
3.1 Dimensions (in inches) ................................................................................................. 3-1
3.2 Weights.......................................................................................................................... 3-3
3.3 Exterior Color ............................................................................................................... 3-3
3.4 Logo ............................................................................................................................... 3-4
3.5 Physical Installation..................................................................................................... 3-4
4 Power Requirements....................................................................................................... 4-1
4.1 AC Power Requirements and Consumption ............................................................... 4-1
4.1.1 Power Source Disturbances .................................................................................. 4-2
4.1.2 Power Entry ........................................................................................................... 4-2
4.1.3 Power Cords........................................................................................................... 4-3
5 Performance Specifications .......................................................................................... 5-1
5.1 Data Cartridge Handling Times.................................................................................. 5-1
5.2 Scan All Barcodes ......................................................................................................... 5-1
6 Environmental Specifications ...................................................................................... 6-1
6.1 Temperature, Humidity, and Altitude........................................................................ 6-1
6.2 Acoustical Noise............................................................................................................ 6-1
XLS-810160/810240 Library Product Specification iii
7 Reliability Specifications............................................................................................... 7-1
7.1 Mean Exchanges Between Failures ............................................................................ 7-1
8 Agency Compliance ......................................................................................................... 8-1
8.1 EEC Directive Compliance (European Economic Community)................................. 8-1
8.1.1 Reduction of Hazardous Substances (RoHS)....................................................... 8-1
8.1.2 XLS Construction Materials................................................................................. 8-1
8.2 Emissions/Immunity Standards Compliance ............................................................. 8-2
8.3 Safety Standards Compliance...................................................................................... 8-2
9 Maintainability ................................................................................................................. 9-1
9.1 Mean Time To Repair................................................................................................... 9-1
9.2 Preventive Maintenance .............................................................................................. 9-1
9.2.1 Controller Battery Replacement .......................................................................... 9-1
9.2.2 Maintaining Controller UPS Protection .............................................................. 9-1
9.3 Tape Drive Cleaning..................................................................................................... 9-1
9.4 Adjustments .................................................................................................................. 9-2
iv 501800 Rev. C
1 Introduction
1.1 Scope
This product specification describes the Qualstar model XLS-810160/810240
intelligent tape libraries. It provides detailed specifications, configuration options, and
installation requirements. This document is intended for use by individuals
evaluating, purchasing, or integrating the XLS-810160/810240 tape libraries.
1.2 Related Documentation
For additional information about the XLS, refer to the documents listed in Table 1-1.
Subject Document Qualstar
Document
Installation XLS Installation Manual 501801
Operation and Administration XLS User Guide 501803
Service XLS Technical Service Manual 501810
Medium Changer Interface XLS Interface Manual 501611
Supported Tape Drives Qualstar Supported Tape Drives PIN-014
Approved Data Cartridges Approved Data Cartridges PIN-038
Barcode Label Specification Barcode Label Information and Specifications PIN-040
SCSI-3 Primary Command Set ANSI INCITS 301:1997, SCSI-3 Primary Commands (SPC)
SCSI-3 Medium Changer
Command Set
Parallel SCSI Standard ANSI X3.302-1998 SCSI Parallel Interface-2 (SPI-2)
Fibre Channel Standard ANSI X3.269:1996 Fibre Channel Protocol (FCP)
TapeAlert
Table 1-1 Related Documents
NCITS 314:1998, SCSI-3 Medium Changer Commands (SMC)
T10/143r0, TapeAlert Specification v 3,
Hewlett-Packard Company.
XLS-810160/810240 Library Product Specification 1-1
2 Product Description
This chapter provides an introduction to the Qualstar XLS-810160/810240 tape
libraries and describes the major features and components.
2.1 General Description
The Qualstar XLS is a mid-range tape library combining an efficient design with an
intelligent system architecture. The XLS library is designed to accommodate a wide
range of storage needs.
The XLS 810240 accommodates up to 10 tape drives, up to 762 cartridges, and up to
two 10-slot I/O ports. The XLS 810160 can accommodate up to 10 tape drives, up to
682 cartridges, and up to two 10-slot I/O ports. The XLS-810160/810240 is shown in
Figure 2-1. An optional expansion pod consisting of 116 tape slots may be installed on
the left side of the unit. Alternatively, both models can also host one XLS-85000
Media Expansion Module (MEM2). The MEM2 houses 517 tape slots.
A system controller within the library oversees the operation of the robotics, tape
drives, and power supplies. It also hosts the X-Link™ library management interface,
which can be accessed locally using the touch screen or remotely across a LAN or the
Internet. Remote monitoring is also supported over Ethernet using SNMP.
Resources in the XLS can be subdivided into as many as eight independent logical
library partitions, with each partition controlled across its own host connection.
Interface offerings include parallel SCSI and Fibre Channel.
Access to the control functions of the XLS is protected by user names and passwords.
XLS-810160/810240 Library Product Specification
2-1
Figure 2-1 XLS-810160/810240
2-2 501800 Rev. C
2 Product Description
2.2 XLS Standard Features
The following features are standard:
• Ability to attach one expansion pod or MEM2 for additional capacity. The expansion
pod can store up to 116 cartridges and the MEM2 can store 517 cartridges.
• Linux-based system controller to oversee the operation of the robotics, sensors, and
power supplies and to provide the library’s management and control interfaces.
• Internal CAN protocol for highly reliable inter-processor communications.
• Integrated support for Fibre Channel and SCSI Library Interface Adapters (LIAs).
Up to four dual-ported LIAs enable host software to control the library’s
medium-changer interface using the standard SCSI-3 command set.
• Support for up to eight independent, user-configurable library partitions. Each
partition (referred to as a logical library) is a subset of the available tape drives,
cartridge slots, and I/O ports.
• Supports Fibre Channel and SCSI LTO tape drives.
• Robotic handler with integrated barcode reader to provide automated inventory
tracking and optical calibration of storage and tape drive positions.
• Up to two I/O ports to facilitate the import and export of cartridges. Each I/O port
includes a removable 10-cartridge magazine.
• Fifteen-inch color touch screen for local configuration, monitoring, and control using
X-Link.
• Highly visible colored LEDs to provide instantaneous status of the library, power
supplies, and tape drives from a distance.
• Comprehensive security system to protect the library from unauthorized access.
Key locks and electronic locks secure the doors. The Inventory Sentry monitors
intrusions into the storage areas and minimizes off-line time.
XLS-810160/810240 Library Product Specification 2-3
2.3 X-Link Features
With a web-based design that supports standard Internet browsers, the X-Link
library management interface can be accessed locally using the color touch screen or
remotely over a LAN or the Internet. The local and remote functions are identical, and
multiple simultaneous connections are supported.
Features of X-Link include the following:
• Menu-based organization that includes customizable content, intuitive controls, and
comprehensive, context-sensitive help.
• Installation and configuration wizards to streamline the installation process.
• Configurable access to various library functions. Using the familiar user group
paradigm, a library administrator can control what tasks each user can perform.
All X-Link users must have valid user IDs and passwords.
• A View Hardware capability that allows library operators to obtain status
information about the tape drives and other hardware components.
• Comprehensive event manager to track and log recent library events. The library
can be configured to send email and pager alerts to specified users when an event
occurs.
• Support for the SNIA Storage Media Library (SML) SNMP MIB, using messages.
The MIB can be downloaded at www.qualstar.com/snia-mib
• Exportable reports and tables. Inventory reports, event logs, and other tables can
be exported to Microsoft Excel, XML, or comma-separated value (CSV) files.
• “Never lost” manuals. The XLS ships with paper manuals, but electronic versions
are always available in Adobe Acrobat PDF format from X-Link or from Qualstar’s
web site.
2.4 XLS High Availability Features
The XLS is designed for 24/7/365 operation and includes the following features for
high availability and “online” serviceability:
• N+1 redundant power system option.
• Dual AC input power option.
• System health monitor and restart manager.
• Automated event reporting via email and pager alerts.
• Remote configuration and management.
• Journaling file system on the system controller for faster recovery from power
losses and system resets.
2-4 501800 Rev. C
Loading...