Quality Craft MM905-54BCP Instruction Manual

Page 1

ELECTRIC FIREPLACE HEATER

MODEL: MM905-54BCP (NDF-68NR)

IMPORTANT: Please note when you open the carton, carefully check the unit and make sure there is no damage. If you have any problems with assembling the unit, with how the various functions work or with damage or missing parts please call 1-800-459-4409 (9:00am - 5:00pm EST) immediately for service.

NOTE: DO NOT RETURN UNIT TO THE STORE BEFORE CALLING THE TOLL FREE NUMBER. Do not dispose of your cartons until you are completely satisﬁed with your new heater.

NOTE: Light bulbs may become loose during shipping. If the ﬂame effect is dim or does not work, please check that the light bulb or bulbs are ﬁnger tight in socket. See instructions for replacing the bulb or bulbs.

INSTRUCTION MANUAL

ATTENTION:

1. Find a location for the ﬁreplace heater that is protected from direct sunlight.

2. Do not plug the unit into the power outlet before reading all instructions.

SAVE THESE INSTRUCTIONS FOR FUTURE USE.

ELECTRIC SHOCK, AND INJURY TO PERSONS, INCLUDI NG THE FOLLOWING:

1) Read all instructions before using this electric ﬁreplace heater.

2) This electric ﬁreplace heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. The grill directly in front of the heater outlet becomes hot during heater operation. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) away from the front of the unit and keep them away from the sides and rear.

3) Extreme caution is necessary when any heater is used by, or near, children or individuals with disabilities and whenever the ﬁreplace is left operating and unattended.

4) Always unplug ﬁreplace when not in use.

5) Do not operate any electric ﬁreplace with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner.

6 Do not use outdoors.

7) This electric ﬁreplace heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.

8) Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from trafﬁc area and where it will not be tripped over.

9) To disconnect ﬁreplace, turn controls to off, then remove plug from outlet.

10) Connect to properly grounded outlets only.

11) Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or ﬁre, or damage the heater.

12) To prevent a possible ﬁre, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.

13) A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or ﬂammable liquids are used or stored.

14) Use this ﬁreplace heater only as described in this manual. Any other use not recommended by the manufacturer may cause ﬁre, electric shock, or injury to persons.

15) Avoid the use of an extension cord because the extension cord may overheat and cause a risk of ﬁre. However, if you have to use an extension cord, the cord shall be No.14 AWG minimum size and rated not less than 1875 watts.

16) Caution: Do not plug this product into a receptacle controlled by a wall switch or dimmer.

17) When storing or transporting the unit and cord, keep in a dry place, free from excessive vibration and store so as to avoid damage.

IMPORTANT SAFETY INSTRUCTIONS

WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE,

CAUTION: IF YOU USE THIS HEATER IN CONJUNCTION WITH A THERMAL CONTROL, A PROGRAM CONTROLLER, A TIMER OR ANY OTHER DEVICE THAT SWITCHES THE HEATER ON AUTOMATICALLY,

Page 2

REMEMBER TO OBSERVE ALL SAFETY WARNINGS AT ALL TIMES. THE FIREPLACE HEATER HAS SAFETY OVERHEAT PROTECTION. IF THE OVERHEAT PROTECTION TRIPS, SWITCH OFF ALL SWITCH BUTTONS AND WAIT APPROXIMATELY 5 -10 MINUTES. IT SHOULD RESET AUTOMATICALLY ONCE THE UNIT COOLS DOWN.

WARNING: PROCEDURES AND TECHNIQUES IF NOT CAREFULLY FOLLOWED WILL RESULT IN DAMAGE TO THE EQUIPMENT AND WILL EXPOSE THE USER TO THE RISK OF SERIOUS INJURY, ILLNESS OR DEATH.

This electric ﬁreplace heater is for use on 120 volts. The cord has a plug as shown at A in illustration below. An adapter as shown at C is available for connecting three-blade grounding-type plugs to two-slot receptacles. The green grounding plug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.

A 15 AMP circuit is required to operate this heater. If the breaker trips when the heater is used then you may need to move the heater to another location or unplug other appliances that are on the same circuit. If you require an extension cord use one that is rated at 1875 watts.

L-shape bracket.......................................................................2

Screws for L bracket ................................................................8

Plastic connectors ....................................................................1

KD screws ...............................................................................3

KD nuts ...................................................................................3

TOOL REQUIRED: PHILLIPS HEAD SCREWDRIVER

ASSEMBLY INSTRUCTIONS

PARTS LIST QTY

A) Top panel..........................................................................1

B) Base (Fireplace insert included)..........................................1

C) Back panel .......................................................................1

D) Base support panel ...........................................................1

E) Left side panel ..................................................................1

F) Right side panel ................................................................1

G) Left inner panel ................................................................1

H) Right inner panel ..............................................................1

W) KD screws ......................................................................72

X) Plastic connectors ...........................................................24

Y) SELF REPAIR SET

Touch-up repair paint (bottle) ....................................................1

MANTEL ASSEMBLY:

CAUTION: PLACE A PIECE OF CARDBOARD OR PROTECTIVE SHEET ON THE FLOOR IN ORDER TO AVOID SCRATCHING THE DECORATIVE SURFACE OF YOUR MANTEL DURING ASSEMBLY.

PLEASE DO NOT FULLY TIGHTEN THE KD SCREWS UNTIL ALL PANELS ARE ASSEMBLED.

NOTE: EACH PLASTIC CONNECTOR IS PRE-ASSEMBLED (PREDRILLED) ON THE SPECIFIC PANELS WITH 2 SCREWS. IF THE KD SCREW(S) DO NOT FIT DURING ASSEMBLY, LOOSEN THE 2

Page 3

(PRE-DRILLED) SCREWS TO ADJUST THE PLASTIC CONNECTOR UNTIL THE KD SCREWS ARE ABLE TO BE INSTALLED. TIGHTEN ALL KD SCREWS ONCE ALL PANELS ARE ASSEMBLED.

Step 1: Attach all plastic connector [X] to panels A, B, C and D with KD screws (2 screws for each plastic connector). See Fig. A.

Step 3: Attach back panel [C] to base [B] with 3 KD screws [W] as shown in Fig. C.

ﬁg. C

Step 4: Attach top panel [A] to the unit as shown in Fig. D with 11 KD screws [W].

ﬁg. A

Step 2: Attach base support panel [D] to the bottom of base [B] with 2 KD screws [W]. Attach panel E, F, G and H on the top of base [B] with 8 KD screws [W]. See Fig. B.

ﬁg. B

ﬁg. D

Step 5: Tighten all screws.

OPERATION

After reading complete instructions, conﬁrm all controls on ﬁreplace are in the OFF position. Plug the ﬁreplace into a 15AMP/120Volt outlet. If the cord does not reach, you may use an extension cord rated for a minimum of 1875 WATTS. Once the ﬁreplace insert has been properly connected to a grounded electrical outlet, it is ready to operate.

OPERATION BY THE CONTROL PANEL

The controls are located behind the grill below the front glass and can be accessed by pulling the grill from the top, forward and down.

Page 4

CAUTION: CENTRE OF GRILL MAY GET HOT DURING OPERATION. DO NOT TOUCH CENTER OF FRONT GRILL WHEN OPENING.

NOTE: When the O/I switch is turned off, the heater functions will

stop even though the switches may be in the ON position.

OPERATION BY THE REMOTE CONTROL

Plug in your electric ﬁreplace and it will beep once, this means you have power and your remote is ready to operate your electric ﬁreplace.

Standby switch. Press this switch once the unit become energized and you can select the following functions as desired. Press this switch again. The unit will be OFF and enter standby mode.

Press this button once for ﬂame effect. The unit will be beep and the indicator light will be ON. The bulbs for ﬂame effect & logset will be ON. To adjust the ﬂame intensity, hold down the button

- the ﬂame optics will go higher or lower. Once you have found the desired setting, release the button. Pressing the button again will stop the light function.

750W: Press this button for low heat level. The unit will beep, the pilot light and indicator light will be on. The ﬁreplace heater will give low heat level. Pressing once again will stop the low heat level function.

1500W: Press this button for high heat level. The unit will beep, the pilot light and indicator light w ill be on. The ﬁreplace heater will give high heat level. Pressing once again will stop the high heat level function.

O/I: Press this button for main power. The indicator light will turn on.

Standby switch. Press this switch once the unit becomes energized and you can select the following functions as desired. Press this switch again. The unit will be OFF and enter standby mode.

- the ﬂame optics will go higher or lower. Once you have found the desired setting, release the button. Pressing the button again will stop the light function.

750 W: Press this button the low heat level. The unit will beep and the indicator light will be ON. The ﬁreplace heater will give off low heat. Pressing once again will stop the low heat level function.

1500 W: Press this button the high heat level. The unit will beep and the indicator light will be ON. The ﬁreplace heater will give off high heat. Pressing once again will stop the high heat level function.

Heat Temperature Control Knob: To adjust the temperature to your individual requirements, turn the temperature control dial to the right (clockwise) to increase the desired temperature and to the left (counter clockwise) for lower temperature.

REMOTE CONTROL BATTERY REPLACEMENT

Replace with 2 AAA batteries.

WARNING: Do not mix old and new batteries Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.

Page 5

MAINTENANCE

WARNING:

Disconnect power and unplug the power cord before attempting any maintenance or cleaning to reduce the risk of ﬁre, electric shock or damage to persons. The bulbs in your unit can become extremely hot. Allow at least 10 minutes between turning off the unit and removing the light bulbs to avoid the accidental burning of the skin.

REPAIR SET

TOUCH-UP REPAIR PAINT

RISK OF FIRE: DO NOT EXCEED THE RECOMMENDED BULB WATTAGE.

REPLACING THE LIGHT BULBS

Step 1: Remove 14 screws on the back of ﬁreplace and open

the rear cover. There are 2 larger screws and 12 smaller

screws. Step 2: You will ﬁnd 1 X 40W Type B-10 bulbs under log-set bed. Step 3: Loosen and remove the burnt out bulb and replace with

new bulb. Step 4: Close the rear cover. Secure the larger screws into the top

left corner hole and bottom right corner holes as shown

in the diagram. Secure the 12 smaller screws into the

remaining holes. Make sure the screws are in the correct

holes and have been tightened. Step 5: Plug in the unit.

Paint directly on the mantel unit if necessary. Fig. A.

Fig. A

REPAIRS

If any problems are found with the original parts during mantel assembly such as the panels cannot be installed with the plastic connector. Try to solve by one of the following methods.

Tools required: Electric drill, drill bits 3/4 inches (10 mm) or 1/16 inches (2 mm), pencil, hammer, Philips screwdriver, safety goggles and gloves (if necessary).

WARNING: Wear goggles before you start drilling.

Option 1:

Use the spare KD NUTS, KD SCREWS and PLASTIC CONNECTOR.

1. Place the PLASTIC CONNECTOR on the mantel unit and mark the drill-holes as shown in Fig. B.

Fig. B

Page 6

2. Drill the holes with diameter 3/4 inches (10 mm) and depth 3/4 inches (10 mm) on the mantel. Each PLASTIC CONNECTOR needs 3 holes. See Fig. C.

Fig. C Fig. D

Fig. G Fig. H

3. Attach the SMALL L-BRACKET and lock in place with SCREWS as shown in Fig. H.

3. Gently install the KD NUTS into the drilled-holes with hammer as shown in Fig. D.

4. Attach the PLASTIC CONNECTOR and lock in place with KD SCREWS as shown in Fig. E.

Fig. E

Option 2:

Use the SMALL L-BRACKETS and SCREWS.

1. Place the SMALL L-BRACKET to the unit as shown and mark the drill-holes on the mantel as shown in Fig. F.

CLEANING

To clean the unit, ﬁrst turn off controls on unit and unplug the unit from the power source. To clean glass display panel; remove dust with clean dry cloth or to remove ﬁnger prints and other marks clean glass with clean damp cloth. Do not use abrasive cleaners or spray liquids on glass display panel surface. Metal and metal painted parts should be cleaned with damp cloth. Do not use abrasive cleaners or spray liquids on these surfaces.

WARRANTY

Every electric ﬁreplace heater is tested before it leaves the factory and it is guaranteed for one year. If the unit should fail to operate correctly within one year from the date of purchase, call customer service at 1-800-459-4409 (EST). We will, at our discretion either repair or replace the unit. It will have to be returned to us freight prepaid and we will return the repaired or replaced unit to you freight prepaid. The company’s sole obligation is to repair or replace the unit.

This warranty is void if in the opinion of Quality Craft the unit has been tampered with, altered, misused, damaged, abused or used with the wrong power source. Light bulbs are not covered by this warranty. The warranty is for homeowner use only and does not cover units used in commercial situations.

Fig. F

2. Drill the holes with diameter 1/16 inches (2 mm) and depth 5/16 inches (8mm) on the mantel. Each SMALL L-BRACKET needs 4 holes. See Fig. G.

Imported by

Quality Craft

Laval, Quebec, Canada H7S 2G7 1-800-459-4409 (EST) www.qualitycraft.com

Made in China