Page 1
ELECTRIC FIREPLACE HEATER
INSTRUCTION MANUAL
M850P-26FDC
NDF-62N
ATTENTION:
1. Find a location for the fireplace heater that is protected
from direct sunlight.
2. Do not plug the unit into the power outlet before you
read all instructions.
Page 2
2
SAFETY INSTRUCTIONS
IMPORTANT
Please note when you open the carton
carefully check the unit and make sure
there are no damages. If you have any
problems with the unit, with how the various
functions work or with hidden damages or
missing parts please call 1-800-459-4409
(EST) immediately for service. NOTE: DO
NOT RETURN UNIT TO THE STORE BEFORE
CALLING THE TOLL FREE NUMBER. Do
not dispose of your cartons until you are
completely satisfied with your new fireplace
heater. Read all instructions thoroughly
before operating your new electric fireplace.
NOTE: Light bulbs may become loose
during shipping. If the flame effect is dim
or does not work, please check that light
bulb or bulbs are finger tight in socket. See
instructions for replacing bulb or bulbs.
Please do not return the sample to the store
before checking light bulbs.
NOTE: The electric fireplace heater may
emit a slight harmless odor when first
turned on. This is caused by activating the
internal heater components for the first time
and should not occur again.
1) Read all instructions before using this
electric fireplace heater.
2) This electric fireplace heater is hot when
in use. To avoid burns, do not let bare skin
touch hot surfaces. The grill directly in front
of the heater outlet becomes hot during
heater operation. Keep combustible materials, such as furniture, pillows, bedding,
papers, clothes, and curtains at least 3 feet
(0.9 m) away from the front of the unit and
keep them away from the sides and rear.
3) Extreme caution is necessary when any
heater is used by, or near, children or individuals with disabilities and whenever the
fireplace is left operating and unattended.
4) Always unplug fireplace when not in use.
5) Do not operate any electric fireplace with
a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged in any manner.
6) Do not use outdoors.
7) This electric fireplace heater is not intended for use in bathrooms, laundry areas
and similar indoor locations. Never locate
heater where it may fall into a bathtub or
other water container.
IMPORTANT SAFETY INSTRUCTIONS
WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE
RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO
PERSONS, INCLUDING THE FOLLOWING:
Page 3
3
8) Do not run cord under carpeting. Do not
cover cord with throw rugs, runners, or
similar coverings. Arrange cord away from
traffic area and where it will not be tripped
over.
9) To disconnect fireplace, turn controls to
off, then remove plug from outlet.
10) Connect to properly grounded outlets
only.
11) Do not insert or allow foreign objects to
enter any ventilation or exhaust opening as
this may cause an electric shock or fire, or
damage the heater.
12) To prevent a possible fire, do not block
air intakes or exhaust in any manner. Do
not use on soft surfaces, like a bed, where
openings may become blocked.
13) A heater has hot and arcing or sparking
parts inside. Do not use it in areas where
gasoline, paint, or flammable liquids are
used or stored.
14) Use this fireplace heater only as
described in this manual. Any other use
not recommended by the manufacturer
may cause fire, electric shock, or injury to
persons.
15) Avoid the use of an extension cord
because the extension cord may overheat
and cause a risk of fire. However, if you have
to use an extension cord, the cord shall be
SAFETY INSTRUCTIONS
No.14 AWG minimum size and rated not
less than 1875 watts.
16) When storing or transporting the unit
and cord, keep in a dry place, free from
excessive vibration and store so as to
avoid damage.
CAUTION
If you use this heater in conjunction with
a thermal control, a program controller,
a timer or any other device that switches
the heater on automatically, remember to
observe all safety warnings at all times. The
stove heater has safety overheat protection.
If the overheat protection trips, unplug the
power cord from the receptacle. It should
reset automatically after 5 minutes.
WARNING
Procedures and techniques if not carefully
followed, will result in damage to the equipment or will expose the user to the risk of
serious injury, illness or death.
This electric fireplace heater is for use on
120 volts. The cord has a plug as shown at
A in illustration below. An adapter as shown
at C is available for connecting three-blade
grounding-type plugs to two-slot receptacles. The green grounding plug extending
from the adapter must be connected to
Page 4
4
a permanent ground such as a properly
grounded outlet box. The adapter should not
be used if a three-slot grounded receptacle
is available. A 15 AMP circuit is required to
operate this heater. If the breaker trips when
the heater is used then you may need to
move the heater to another location or unplug other appliances that are on the same
circuit. If you require an extension cord use
one that is rated at 1875 watts.
SAVE THESE
INSTRUCTIONS
FOR FUTURE USE.
SAFETY INSTRUCTIONS
Page 5
5
ASSEMBLY INSTRUCTIONS
PARTS LIST:
Fireplace insert 1
A) Top panel 1
B) Base panel 1
C) Upper front panel 1
D) Lower front panel 1
E) Left front panel 1
F) Right front panel 1
G) Left upper side panel 1
H) Right upper side panel 1
J) Left lower side panel 1
K) Right lower side panel 1
P) Wood connectors 4
Q) Large “L” brackets 2
R) Nuts 2
S) Washers 2
T) Small screws 2
U) Short KD screws 5
W) KD screws 51
X) Plastic connectors 11
Y) SELF REPAIR SET
Touch-up repair paint (bottle)
L-shape bracket 2
Screws for L bracket 8
Plastic connectors 1
KD screws 3
KD nuts 3
Z) WALL ANCHOR SAFETY CABLE
Wall anchor 1
Screw for wall anchor 1
Screw for mantel 1
Safety cable 1
TOOL REQUIRED: PHILLIPS HEAD SCREWDRIVER
MANTEL ASSEMBLY:
CAUTION: Place a piece of cardboard or
protective sheet on the floor in order to avoid
scratching the decorative surface of your
mantle during assembly.
Please DO NOT fully tighten the KD screws
until all panels are assembled.
NOTE: Each plastic connector is pre-assembled (pre-drilled) on the specific panels with
2 screws. If the KD screw(s) do not fit during
assembly, loosen the 2 (pre-drilled) screws
to adjust the Plastic Connector until the KD
screws are able to be installed. Tihten all KD
screws once all panels are assembled.
Step 1: Attach 11 PLASTIC CONNECTORS [X] to
PANELS C, E, F, G, H, J and K as shown in Fig.
A (2 pcs KD screws for each PLASTIC CONNECTOR). Attach PANELS H and K together
with 4-HOLES WOOD CONNECTOR [S] and 4
KD screws. Attach PANELS G and J together
with 4-HOLES WOOD CONNECTOR [S] and 4
KD screws. See Fig A.
Page 6
6
Fig. A
Step 2: Attach PANEL E to PANEL G and J
with 1 KD screw. Attach PANEL F to PANEL
H and K with 1 KD screw. See Fig. B.
Fig. B
Step 3: Attach 2 x 4-HOLES WOOD CONNECTORS [S] to PANEL E and F with 4 KD
SCREWS (2 screws for each wood connector). Attach Panels E, G and J to BASE
PANEL [B] with 2 KD SCREWS. Attach
PANELS F, H and K to BASE PANEL [B] with
2 KD SCREWS. See Fig. C.
Fig. C
Step 4: Attach LOWER FRONT PANEL [D]
to the unit as shown in Fig. D with 2 KD
SCREWS. See fig. D.
Fig. D
Step 5: Attach UPPER FRONT PANEL [C]
to the unit as shown in Fig. E with 6 KD
SCREWS. See fig. E.
Fig. E
ASSEMBLY INSTRUCTIONS
Page 7
7
Step 6: Attach TOP PANEL [A] on top with
3 KD SCREWS. See fig. F
Fig. F
Step 7: Tighten all KD SCREWS.
FIREPLACE INSERT
INSTALLATION:
The fireplace insert can be installed after the
mantel has been fully assembled.
WARNING: Make sure the fireplace insert
controls are in the OFF position and the unit
is NOT plugged in.
Step 1: Attach 2 Large “L” brackets [Q] to
each side of the fireplace insert with washers [S] and secured with small screws [T]
and nuts [R]. See Fig. G.
Fig. G
Step 2: Attach fireplace insert into the unit
as shown in Fig. H with 5 screws [U]. (3 KD
short screws at the top of the insert and 2
short KD screws at the Large “L” bracket
[Q]). See Fig. H.
Fig. H
Step 3: Move assembled unit to desired
location. Unit should not be positioned in
area exposed to direct sunlight.
ASSEMBLY INSTRUCTIONS
Page 8
8
OPERATION
WALL ANCHOR
SAFETY CABLE
The use of WALL ANCHOR SAFETY CABLE
is highly recommended in order to reduce
the risk of the fireplace being tipped over
accidentally. WARNING: This CABLE may
reduce possible risk of injury if the fireplace
is improperly handled, but is not a substitute for proper adult supervision. Children
should not be left unattended near any
heater.
1. Drill a 5/16 in (8 mm) hole in the wall.
Insert the PLASTIC WALL ANCHOR into the
hole and gently tap until the flange on the
anchor is against the wall surface.
2. Position the back edge of the mantle close
to the wall.
3. Attach the SAFETY CABLE to the mantle
using the SCREW FOR MANTEL.
4. Use the SCREW FOR WALL to attach the
other end of SAFETY CABLE to the wall.
5. Make sure all screws are tight.
Wall
OPERATION
After reading complete instructions, confirm
all controls on fireplace are in the OFF position. Plug the fireplace into a 15AMP/120Volt
outlet. If the cord does not reach, you may
use an extension cord rated for a minimum
of 1875 WATTS. Once the fireplace insert
has been properly connected to a grounded
electrical outlet, it is ready to operate.
OPERATION BY THE
CONTROL PANEL
The controls are located behind the grill
below the front glass and can be accessed
by pulling the grill from the top, forward and
down.
WARNING: DO NOT TOUCH. HOT SURFACE
AT CENTRE OF GRILL. HANDLE LEFT OR
RIGHT SIDE OF GRILL WHEN PULLING OUT.
Page 9
9
MAINTENANCE
O/I: Press this button for main power and
flame effect. The indicator light will turn on.
See below for other control switches.
1250W: For heat function - Press this switch
while the O/I switch is in the ON position.
The indicator light will turn ON.
TEMPERATURE CONTROL: To adjust the
temperature to your individual requirements, turn the temperature control dial to
the right (clockwise) to increase the desired
temperature and to the left for lower temperature. This temperature control dial can
only be used while the O/I switch and 1250W
switch are in the ON position.
NOTE: When the O/I switch is turned off, the
heater functions will stop even though the
switches may be in the ON position.
MAINTENANCE
WARNING:
Disconnect power and unplug the power
cord before attempting any maintenance or
cleaning to reduce the risk of fire, electric
shock or damage to persons. The bulbs in
your unit can become extremely hot. Allow
at least 10 minutes between turning off the
unit and removing the light bulbs to avoid
the accidental burning of the skin.
RISK OF FIRE: DO NOT EXCEED
THE RECOMMENDED BULB
WATTAGE.
REPLACING THE FLAME
EFFECT LIGHT AND
LOG-SET LIGHT BULBS
Step 1: Remove 12 screws on the back of
fireplace and open the rear cover. There are
2 larger screws and 10 smaller screws.
Step 2: You will find 1 X 40W Type B-10 bulb
under log-set bed.
Step 3: Loosen and remove the burnt out
bulb and replace with new bulb.
Step 4: Close the rear cover. Secure the 2
larger screws into the top left corner hole
and bottom right corner holes as shown
in the diagram. Secure the 10 smaller
screws into the remaining holes. Make
sure the screws are in the correct holes
and have been tightened.
Step 5: Plug in the unit.
Page 10
10
OPTION 1:
Use the spare KD NUTS, KD SCREWS and
PLASTIC CONNECTOR.
1. Place the PLASTIC CONNECTOR on the
mantel unit and mark the drill-holes as
shown in Fig. B.
fig. B
2. Drill the holes with diameter 3/4 inches
(10 mm) and depth 3/4 inches
(10 mm) on
the mantel. Each PLASTIC CONNECTOR
needs 3 holes. See Fig. C.
fig. C
fig. D
3. Gently install the KD NUTS into the
drilled-holes with hammer as shown in
Fig. D.
4. Attach the PLASTIC CONNECTOR and
lock in place with KD SCREWS as shown
in Fig. E.
REPAIR SET
TOUCH UP REPAIR PAINT
Paint directly on the mantel unit if
necessary. Fig. A.
fig. A
REPAIRS
If any problems are found with the original parts during mantel assembly such
as the panels cannot be installed with the
plastic connector. Try to solve by one of
the following methods.
Tools required: Electric drill, drill bits 3/4
inches (10 mm) or 1/16 inches (2 mm),
pencil, hammer, Philips screwdriver,
safety goggles and gloves (if necessary).
WARNING: Wear goggles before you start
drilling.
REPAIR SET
Page 11
11
fig. E
OPTION 2:
Use the SMALL L-BRACKETS and
SCREWS.
1. Place the SMALL L-BRACKET to the
unit as shown and mark the drill-holes on
the mantel as shown in Fig. F.
fig. F
2. Drill the holes with diameter 1/16 inches (2 mm) and depth 5/16 inches (8 mm)
on the mantel. Each SMALL L-BRACKET
needs 4 holes. See Fig. G.
fig. G fig. H
3. Attach the SMALL L-BRACKET and lock
in place with SCREWS as shown in Fig. H.
CLEANING
To clean unit first turn off controls on unit
and unplug the unit from power source. Toclean glass display panel; remove dust with
clean dry cloth or to remove finger prints
and other marks clean glass with clean
damp cloth. Do not use abrasive cleaners or
spray liquids on glass display panel surface.
Metal and metal painted parts should be
cleaned with damp cloth. Do not use
abrasive cleaners or spray liquids on
these surfaces.
WARRANTY
Every electric fireplace heater is tested
before it leaves the factory and it is guaranteed for one year. If the unit should fail
to operate correctly within one year from
the date of purchase, call customer service
REPAIR SET / CLEANING
Page 12
12
at 1-800-459-4409 (EST). We will, at our
discretion either repair or replace the unit. It
will have to be returned to us freight prepaid
and we will return the repaired or replaced
unit to you freight prepaid. The company’s
sole obligation is to repair or replace the
unit. This warranty is void if in the opinion
of Quality Craft the unit has been tampered
with, altered, misused, damaged, abused
or used with the wrong power source. Light
bulbs are not covered by this warranty. The
warranty is for homeowner use only and
does not cover units used in commercial
situations.
Imported by
Quality Craft
Surrey, BC, Canada V3S 5N4
1-800-459-4409 (EST)
www.qualitycraft.com
Made in China
WARRANTY
Page 13
13
Loading...