QG-DB-001-BLK
SINGLE SHELF WALL MOUNT
8kg
8kg
(17.6lbs)
(17.6lbs)
Version March 2016Version March 2016
Do not exceed the maximum rated weight
specified. Otherwise, serious injury or
property damage may occur.
Please read the entire installation manual before you start installation and assembly.
NOTE
WARNING
Do not begin to install your QualGear product
until you have read and understood all the
instructions and warnings contained in this
installation manual. If you have any questions
regarding the instructions, for US customers
please contact QualGear customer support
via email at support@qualgear.com. For
all international customers, please contact
your local distributor.
This product should only be installed by
someone of good mechanical aptitude, has
experience with basic building construction,
and fully understands these instructions.
This product was designed to be installed
and utilized only as specified in this manual.
Improper installation of this product may cause
damage or serious injury. QualGear is not
liable for the improper use or installation of its
products.
Tighten screws firmly, but do not over tighten.
Over tightening can damage the items, greatly
reducing their holding power.
ALL QUALGEAR products are intended for
indoor use only and any outdoor use voids the
limited warranty.
ALL QUALGEAR products are designed
and tested for residential use only and any
commercial use voids the limited warranty.
For warranty information, please visit
http://www.qualgear.com/warranty.php.
If mounting to wooden studs, make sure that
mounting screws are anchored into the center
of the studs. Use of an edge-to-edge stud finder
is highly recommended.
Never exceed the maximum rated weight
specified in this manual.
Parts Checklist
IMPORTANT: Before starting installation, please check that all parts shown in this checklist
are included. If any parts are missing or damaged, contact your local distributor or
support@qualgear.com for replacement parts and do not start assembly and installation
until you receive all the parts.
Glass Holder (x1)
B
QG-DB- 001-BLK
Marking Template (x1)
F
Wall Plate (x1)
C
Glass Shelf (x1)
A
Connecting Piece (x1)
D
Decorative Cover (x2)
E
Make sure that the supporting surface
will safely support the combined load of
the
equipment and all attached hardware and
components.
Always use an assistant or mechanical
lifting equipment to safely lift and position the
All bolts and screws must be used at the
designated points in the installation instructions
to prevent property damage and/or personal
injury.
DO NOT install near air conditioner vents or
where there is excessive dust or smoke.
Hardware Package
equipment.
When drilling holes in the wall, it is very
important to take care of electrical cables,
water, or gas pipes in the wall.
This product was designed to be installed on the following wall construction only:
ST5.5x50mm
Lag Bolt (x2)
P-A
8x36mm
Concrete Anchor (x2)
P-B
WALL CONSTRUCTION HARDWARE REQUIRED
Wooden Stud Included
Wooden Beam Included
Solid Concrete Included
Plastic Bush (x1)
P-D
Plastic Cap (x2)
P-E
3mm Allen Key (x1)
P-F
Other Contact Qualified Professional
1 2
1a
Mounting to a Wooden Stud Wall
Stud Finder
NOTE
For concrete wall
mounting, follow
Step 1b.
Wall Plate
C
P-A
1
Using an edge-to-edge stud finder, find the
edges of the stud.
F
QG-DB-0 01-BLK
3
Using the marking template (F) provided,
mark two holes for drilling on the centerline of
the stud.
2
Using a level, mark the centerline of the stud.
50mm
50mm
(2")
(2")
ø 4mm
(ø 5/32")
4
Using a power drill and 5/32" drill bit, drill
pilot holes of 5/32" (4 mm) diameter and at
least 2" (50 mm) depth.
5
Mount the wall plate (C) and tighten it with the provided
lag bolts (P-A) using a proper Phillips Screwdriver.
NOTE
Do NOT use power drill and do NOT over tighten the lag bolts.
WARNING
Make sure that mounting screws are anchored into the center of the studs. The use
of a stud finder is highly recommended.
Installers are responsible to provide hardware for other types of mounting situations.
Installers must verify that the supporting surface will safely support the combined
weight of the equipment and all attached hardware and components.
SKIP TO STEP 2
3
4
Mounting to a Concrete Wall
1b
Marking Template
F
QG-DB -001-BLK
1
Hold the marking template (F) provided against the wall where you want to install your AV
equipment, mark two holes for drilling.
NOTE
Do NOT use power drill and do NOT over tighten the lag bolts.
Wall Plate
C
P-B
P-A
55mm
55mm
(2.2")
(2.2")
ø 8mm
(ø 5/16")
2
Using a power drill and a 5/16" masonry drill bit, drill mounting holes of 5/16" (8 mm) diameter
and 2.2" (55 mm) depth at the marked locations in the previous step.
5
Place concrete anchors (P-B) in each hole. Tap each anchor flush with the wall using a hammer.
3
Using a proper Phillips screwdriver, mount the wall plate (C) and fasten them with the provided
lag bolts (P-A).
WARNING
Installers must verify that the supporting surface will safely support the combined
weight of the equipment and all attached hardware and components.
6
6
Assembling the Glass Holder and the Connecting Piece
2
Connecting Piece
D
P-C
P-F
Glass Holder
B
NOTE
Tighten screws until
3mm of space is
between part D and B
P-F
P-C
Install the connecting piece (D) to the glass holder (B).
Installing the Glass Holder to the Wall Plate
3
Glass Holder
B
Insert the glass holder along the wall plate rail,
then slide it down to the desired position.
Top View
Glass Holder
B
Wall Plate
C
At the desired location, use the
allen key to tighten the screws
until the glass holder is secured.
Decorative Cover
E
P-E
Install the decorative covers
and the plastic caps.
7
8
4
Installing the Glass Shelf
P-F
P-F
P-C
If adjustment is necessary, loosen screws
P-C with allen key P-F, slide the glass
holder to the desired position then tighten
screws again to secure.
P-C
Cable Management
5
(AV equipment not included)
Glass Holder
B
Attach the glass shelf to the glass holder using the screw and the plastic bush.
NOTE
Tighten all screws but do not over tighten.
9
Glass Shelf
A
P-D
Place the glass gently on the mounted glass holder. Run the cable through the cable clips.
10
Loading...