7
Wall
Tighten all bolts and
NOTE
screws after adjusting
the TV.
3
N
TV
O
Tension was preset at the factory. To adjust tension, loosen
or tighten arm adjustment bolts using allen key (N) and
wrench (O). TV or monitor can be adjusted to desired location
by tilting and swiveling the bracket.
11
55
30kg
(66lbs)
RATED
1 Year Limited Warranty
Version: December 2015
Version: December 2015
23
55
75x75 | 100x100 | 200x100 | 200x200
300x300 | 400x200 | 400x400
Please read the entire installation manual before you start installation and assembly.
NOTE
WARNING
Do not begin to install your QualGear product
until you have read and understood all the
instructions and warnings contained in this
installation manual. If you have any questions
regarding the instructions, for US customers
please contact QualGear customer support
via email at support@qualgear.com. For
all international customers, please contact
your local distributor.
This product should only be installed by
someone of good mechanical aptitude, has
experience with basic building construction,
and fully understands these instructions.
This product was designed to be installed
and utilized only as specified in this manual.
Improper installation of this product may cause
damage or serious injury. QualGear is not
liable for the improper use or installation of its
products.
Make sure that the supporting surface
will safely support the combined load of the
equipment and all attached hardware and
components.
Tighten screws firmly, but do not over tighten.
Over tightening can damage the items, greatly
reducing their holding power.
ALL QUALGEAR products are intended for
indoor use only and any outdoor use voids the
limited warranty.
ALL QUALGEAR products are designed
and tested for residential use only and any
commercial use voids the limited warranty.
For warranty information, please visit
http://www.qualgear.com/warranty.php.
If mounting to wooden studs, make sure that
mounting screws are anchored into the center
of the studs. Use of an edge-to-edge stud finder
is highly recommended.
Never exceed the maximum rated weight
specified in this manual.
All bolts and screws must be used at the
designated points in the installation instructions
to prevent property damage and/or personal
injury.
Parts Checklist
IMPORTANT: Before starting installation, please check that all parts shown in this checklist
are included. If any parts are missing or damaged, contact your local distributor or
support@qualgear.com for replacement parts and do not start assembly and installation
until you receive all the parts.
HDMI Cable (x1)
1
WALL MARKING TEMPLATE
3-Axis Magnetic Bubble Level (x1) Wall Mount (x1) Wall Marking Template (x1)
Hardware Package
M6.3x65mm Lag Bolts (x3)
A
10x61mm Concrete/ Brick Anchors (x3)
B
D6 Washers (x3)
C
Always use an assistant or mechanical
lifting equipment to safely lift and position the
DO NOT install near air conditioner vents or
where there is excessive dust or smoke.
D8.5xD17x10mm Spacers (x4)
D5 Washers (x4)
ED
GF
equipment.
When drilling holes in the wall, it is very
important to take care of electrical cables,
water, or gas pipes in the wall.
This product was designed to be installed on the following wall construction only:
IH
LKJ
WALL CONSTRUCTION HARDWARE REQUIRED
Wooden Stud Included
Wooden Beam Included
Solid Concrete Included
dedulcnI kcirB
M
Allen Key (x1) Wrench (x1)
PON
D6 Plastic Washers (x8)
Q
Other Contact Qualified Professional
1 2
1
Remove the VESA Plate
2a
Mounting to a Wooden Stud Wall
Stud Finder
For concrete or brick
NOTE
wall mounting, follow
Step 2b.
1
Loosen and remove the VESA plate screws on the VESA plate as shown above.
2
Lift and remove the VESA plate from the mount as shown above.
VESA Plate Screws
VESA Plate
WARNING
Make sure that mounting screws are anchored into the center of the studs. The use
of a stud finder is highly recommended.
Installers are responsible to provide hardware for other types of mounting situations.
Installers must verify that the supporting surface will safely support the combined
TIP
weight of the equipment and all attached hardware and components.
1
Using an edge-to-edge stud finder, find the
edges of the stud.
Marking Template
Using the marking template provided, mark
three holes for drilling on the centerline of the
stud.
2
Using a level, mark the centerline of the stud.
65mm
65mm
(2.5")
(2.5")
ø 4.5mm
(ø 3/16")
43
Using a power drill and 3/16" drill bit, drill
pilot holes of 3/16" (4.5mm) diameter and at
least 2.5" (65mm) depth at the marked
locations in the previous step.
3
4
C
70mm
70mm
(2.7")
(2.7")
ø 10mm
(ø 3/8")
2
WARNING
Installers must verify that the
supporting surface will safely
support the combined weight of
the equipment and all attached
hardware and components.
A
5
Mount the wall plate and tighten with the provided lag bolts (A) and D6 washers (C) using a
socket wrench.
NOTE
2b
Do NOT use power drill and do NOT over tighten the lag bolts.
Do NOT use concrete / brick anchors (B) for drywalls.
Mounting to a Concrete or a Brick Wall
Level
SKIP TO STEP 3
Marking Template
Using a power drill and a 3/8" masonry drill bit, drill mounting holes of 3/8" (10mm) diameter and 2.7"
(70mm) depth at the marked locations in the previous step.
B
C
A
3
Place concrete anchors (B) in each hole. Tap each anchor flush with the wall using a hammer. Mount
the wall plate and tighten with the provided lag bolts (A) and D6 washers (C) using a socket wrench.
Installing the Decorative Covers
3
Concrete Wall
Wall
1
Hold the marking template provided against the wall where you want to install the TV, mark
three holes for drilling.
5
Decorative Covers
Insert the decorative covers along the wall plate rail until they fit snuggly onto the wall plate.
6
Installing the VESA Plate
4a
For VESA: 200x200mm or smaller
Flat Back Panel
VESA Plate
CAUTION!
For TVs with mounting hole
patterns VESA 200x200mm
or smaller, move the VESA
plate up or down to select a
different mounting position
to avoid blocking the input
panel on the back of the TV.
Select the proper screw by hand tightening
screws to check thread depth for your TV.
F/ H/ J/ L
4b
Installing the VESA Plate
For VESA: 300x200, 400x200mm
Choose the appropriate screws, washers, and
spacers (if necessary) according the type of
your TV, attach the VESA plate to the back of
the TV and tighten screws using a screwdriver.
(see below)
For TVs with curved back, use spacers
as needed. Use washers for M4 or M5
NOTE
screws only.
For VESA 300x200mm, 400x200mm,
attach extension arms as shown.
P
Q
"
"
"
Top of the TV
Back of the TV
Curved Back Panel
Top of the TV
Back of the TV
Choose the appropriate screws, washers, and spacers (if necessary)
according the type of your TV, attach the VESA plate to the back of
the TV and tighten screws using a screwdriver.
7
(Use for F/ H only)
E
Flat Back Panel
F/ H/ J/ L
(Use for F/ H only)
E
G/ I/ K/ M
(Use for G/ I only)
E
Top of the TV
Back of the TV
Curved Back Panel
D
Top of the TV
Tighten all screws but
NOTE
do NOT over tighten.
SKIP TO STEP 5 SKIP TO STEP 5
Back of the TV
D
G/ I/ K/ M
(Use for G/ I only)
E
8
4c
Installing the VESA Plate
5
Hanging the TV onto the Wall Mount
For VESA: 300x300, 400x400mm
"
"
"
"
For TVs with curved back, use spacers
as needed. Use washers for M4 or M5
NOTE
screws only.
Flat Back Panel
Top of the TV
Back of the TV
For VESA 300x300mm, 400x400mm,
attach extension arms as shown.
P
Q
Choose the appropriate screws, washers, and
spacers (if necessary) according the type of
your TV, attach the VESA plate to the back of
the TV and tighten screws using a screwdriver.
(see below)
F/ H/ J/ L
(Use for F/ H only)
E
TV
Using an assistant, hang the TV onto the
wall bracket as shown above.
TV
Wall
HEAVY!
Use an ass istant
for this step.
Wall
VESA Plate Screws
Then, while holding the TV securely by an assistant, ensure the VESA plate screws are
tightened by using a screwdriver.
6
Curved Back Panel
Top of the TV
Back of the TV
9
Wall
G/ I/ K/ M
Keep the cables
(Use for G/ I only)
E
D
To connect the cables to your TV, run the cables through the cable clip.
loose for cantilever
arm movement.
10
Loading...