Page 1
Installing the Safety Bar and the Padlock
5
IMPORTANT: Make sure the TV is safely secured before releasing
The folded edge
faces inward.
Adjustment
6
Safety Bar
B
Insert the safety bar onto the rail (at the bottom of
the wall plate) to secure. Put a padlock on the safety
bar to prevent the TV from being stolen.
QG-TM-031-BLK
HEAVY DUTY TILTING TV WALL MOUNT
Padlock is not
included
Tilt
-10°~+5°
Push or pull from
the top or bottom of the
screen to obtain
the desired angle.
70
40kg
40kg
(88lbs)
(88lbs)
Version March 2016
Version March 2016
For Most 37" to 70" Flat Panel and
Curved TVs
Do not exceed the maximum rated weight
specified. Otherwise, serious injury or
property damage may occur.
300x300 400x200 400x400 600x400
Page 2
Please read the entire installation manual before you start installation and assembly.
NOTE
WARNING
Do not begin to install your QualGear product
until you have read and understood all the
instructions and warnings contained in this
installation manual. If you have any questions
regarding the instructions, for US customers
please contact QualGear customer support
via email at support@qualgear.com. For
all international customers, please contact
your local distributor.
This product should only be installed by
someone of good mechanical aptitude, has
experience with basic building construction,
and fully understands these instructions.
This product was designed to be installed
and utilized only as specified in this manual.
Improper installation of this product may cause
damage or serious injury. QualGear is not
liable for the improper use or installation of its
products.
Tighten screws firmly, but do not over tighten.
Over tightening can damage the items, greatly
reducing their holding power.
ALL QUALGEAR products are intended for
indoor use only and any outdoor use voids the
limited warranty.
ALL QUALGEAR products are designed
and tested for residential use only and any
commercial use voids the limited warranty.
For warranty information, please visit
http://www.qualgear.com/warranty.php.
If mounting to wooden studs, make sure that
mounting screws are anchored into the center
of the studs. Use of an edge-to-edge stud finder
is highly recommended.
Never exceed the maximum rated weight
specified in this manual.
Parts Checklist
IMPORTANT: Before starting installation, please check that all parts shown in this checklist
are included. If any parts are missing or damaged, contact your local distributor or
support@qualgear.com for replacement parts and do not start assembly and installation
until you receive all the parts.
Wall Plate (x1)
A
Safety Bar (x1)
B
ST2.9x6.5 Screw (x4)
G
Left Adapter Bracket (x1)
C
Bubble Level (x1)
E
Marking Template (x1)
Right Adapter Bracket (x1)
Decorative Cover (x2)
F
QG-TM-031-BLK
H
Hardware Package
D
Make sure that the supporting surface
will safely support the combined load of
the
equipment and all attached hardware and
components.
Always use an assistant or mechanical
lifting equipment to safely lift and position the
All bolts and screws must be used at the
designated points in the installation instructions
to prevent property damage and/or personal
injury.
DO NOT install near air conditioner vents or
where there is excessive dust or smoke.
M4x14mm (x4)
M-A
M5x14mm (x4)
M-B
M6x14mm (x4)
M-C
M8x20mm (x4)
M-D
M6x30mm (x4)
M-E
equipment.
When drilling holes in the wall, it is very
important to take care of electrical cables,
water, or gas pipes in the wall.
This product was designed to be installed on the following wall construction only:
M8x30mm (x4)
M-F
5.5mm/8.5mm
Washer (x4)
M-G
5mm
Small Spacer (x8)
M-H
15mm
Large Spacer (x4)
M-I
WALL CONSTRUCTION HARDWARE REQUIRED
Wooden Stud Included
Wooden Beam Included
Solid Concrete Included
Other Contact Qualified Professional
ST6.3x65mm
Lag Bolt (x6)
W-A
10x60mm
Concrete Anchor (x6)
W-B
D6 Washer (x6)
W-C
1 2
Page 3
1
Installing the Decorative Covers
When decorative covers are installed correctly,
there will be a gap between the bottom of the wall
NOTE
plate and the decorative covers. This gap is for the
safety bar installation on Step 5.
Decorative Cover
F
65mm
65mm
(2.5")
(2.5")
ø 4.5mm
(ø 3/16")
H
QG-TM-031-BLK
Attach the decorative covers to the wall plate using the screws.
2a
Mounting to a Wooden Stud Wall
Stud Finder
ST2.9x6.5 Screw
G
NOTE
For concrete wall
mounting, follow
Step 2b.
3
Using the marking template (H) provided,
mark four holes for drilling on the centerline of
the stud.
Wall Plate
A
5
Mount the wall plate (A) and tighten it with the provided
lag bolts (W-A) and D6 washers (W-C) using a socket wrench.
NOTE
Do NOT use power drill and do NOT over tighten the lag bolts.
4
Using a power drill and 3/16" drill bit, drill
pilot holes of 3/16" (4.5 mm) diameter and at
least 2.5" (65 mm) depth.
WARNING
Bubble Level
E
Insert the bubble level (E)
on the wall plate (A)
W-C
W-A
1
Using an edge-to-edge stud finder, find the
edges of the stud.
3
2
Using a level, mark the centerline of the stud.
Make sure that mounting screws are anchored into the center of the studs. The use
of a stud finder is highly recommended.
Installers are responsible to provide hardware for other types of mounting situations.
Installers must verify that the supporting surface will safely support the combined
weight of the equipment and all attached hardware and components.
SKIP TO STEP 3
4
Page 4
Mounting to a Concrete Wall
2b
NOTE
Do NOT use power drill and do NOT over tighten the lag bolts.
Bubble Level
E
Marking Template
H
QG-TM-03 1 -BLK
1
Hold the marking template (H) provided against the wall where you want to install the TV,
mark six holes for drilling.
70mm
70mm
(2.7")
(2.7")
Wall Plate
A
Insert the bubble level (E)
on the wall plate (A)
W-B
W-C
W-A
ø 10mm
(ø 3/8")
2
Using a power drill and a 3/8" masonry drill bit, drill mounting holes of 3/8" (10 mm) diameter
and 2.7" (70 mm) depth at the marked locations in the previous step.
5
Place concrete anchors (W-B) in each hole. Tap each anchor flush with the wall using a hammer.
3
Using a socket wrench, mount the wall plate (A) and fasten them with the provided lag bolts
(W-A) and D6 washers (W-C).
WARNING
Installers must verify that the supporting surface will safely support the combined
weight of the equipment and all attached hardware and components.
6
Page 5
Installing to a Flat Back Panel of a TV
3a
M-A/ M-B
Choose the appropriate screws and washers according to the type of your
TV, and attach adapter brackets (C and D) to the back of the TV using a
Phillips screwdriver.
D
Right Adapter Bracket
Top Backside of the TV
Left Adapter Bracket
C
OR
M-G
5.5mm
Flat Back
Panel
M-C/ M-D
M-G
8.5mm
Top of the TV
According to the direction
indicator arrows on the
NOTE
IMPORTANT!
Tighten all screws but
do NOT over tighten
7
adapter brackets, make
sure the adapter brackets
are installed in the correct
direction.
8
Page 6
Installing to a Curved or Recessed Back Panel of a TV
3b
Choose the appropriate screws, washers, and spacers (if necessary) according to the type of your
TV and attach adapter brackets (C and D) to the back of the TV using a Phillips screwdriver.
Right Adapter Bracket
D
Curved
Left Adapter Bracket
C
Top Backside of the TV
OR
NOTE
IMPORTANT!
Tighten all screws but
do NOT over tighten
Recessed
Back Panel
According to the direction
indicator arrows on the
adapter brackets, make
sure the adapter brackets
are installed in the correct
direction.
8.5mm
Hooking the TV onto the Wall Plate
4
M-D
M-G
M-H
OR
M-E/ M-F
M-G
M-I
M-D/ M-E/ M-F
M-G
M-H
M-H
M-E/ M-F
M-G
M-H
M-I
Back Panel
9
Top Backside of the TV
With an assistant, hook the TV
onto the mounted wall plate.
10
Loading...