Qualcraft Heavy Duty Fixed Roof Bracket User Manual

HEAVY DUTY ROOFING BRACKETS

ROOFING

PRODUCTS

FIXED & ADJUSTABLE Roong Brackets

Durable all steel construction sized to fit specific, common roof pitches. Can be easily installed and removed without damaging shingles. The capacity is one worker per 8 foot staging plus 40lbs., with a maximum of 8 feet between brackets.

For use on 21/12 PITCH ROOFS

Model #2503 6" x 60º

For use on 12/12 PITCH ROOFS

Model #2501 10" x 45º Model #2504 6" x 45º

USE ONLY AS A SLIDEGUARD OR MATERIAL SUPPORT

Model #2502 6" x 90º

FOR USE AS MATERIAL SUPPORT ONLY

Model #2505 4" x 90º

Product Specications

Model # 2501 2502 2503 2504 2505

Description: 10” x 45 Degree 6” x 90 Degree 6” x 60 Degree 6” x 45 Degree 4” x 90 Degree

Unit Pack: 10 / Carton 10 / Carton 10 / Carton 10 / Carton 10 / Carton

Weight per Pack: 23 Pounds / Carton 22.6 Pounds / Carton 22.6 Pounds / Carton 22.6 Pounds / Carton 22 Pounds/Carton

Cu. Ft. per Pack: .52 cu. ft. .99 cu. ft. .63 cu. ft. .63 cu. ft. .63 cu. ft.

Customer Support and Ordering Information

PO Box 559 • Stoughton, MA 02072

781-344-1000 • www.qualcraft.com

ROOFING PRODUCTS

INSTRUCTIONS FOR INSTALLATION AND USE OF THE MODEL #2501 & #3501 10”x 45 DEGREE, MODEL #3504 8” x 45 DEGREE PITCH ROOFING BRACKET (FOR USE ON 12/12 PITCH ROOFS): CAPACITY: One worker per 8 feet of scaffolding plus 40 pounds of materials. GENERAL REQUIREMENTS: When installed, the plat-

form support arm must be set to match the pitch of the roof, allowing for the installation of a fully decked and level walk surface. MOUNTING THE ROOF BRACKET: 1) All brackets shall be attached to the roof with 20-penny nails. Use all slots on mounting plate. 2) Position bracket so that all nails penetrate both the roof’s surface and the rafter below.

3) Spacing between brackets shall not exceed 8 feet. INSTALLING PLATFORM: 1) wood platforms shall not be less than 2 inches nominal thickness and shall extend beyond the support arm not less than 6 inches and not more than 12 inches.

2) Always use clear, straight-grained wood free from knots or defects. 3) If extended length platforms are required, use additional Roof Brackets every 8 feet. 4) Secure to bracket by nailing the platform to the bracket using the hole provided in the platform retainer. INSTRUCTIONS FOR USE: 1) No more than one person shall occupy any given 8 feet of a Roong Bracket Scaffold. 2) Always use OSHA compliant fall arrest system, guardrails, catch platforms or other safety equipment as required by Local, State or Federal OSHA Regulations. 3) Roof Brackets are intended for use by the experienced tradesman. 4) OSHA Regulations require that employers provide training in the use and care of this product. CARE AND MAINTENANCE: 1) Inspect all Roong Brackets before each use to be sure that there is no damage or deformation, or deterioration from rusting. Discard if necessary. 2) Do not throw or drop from a building or onto a truck. 3) Do not use if exposed to extreme heat or cold. Discard at once. 4) Do not use if wet or frozen.

60˚ 45˚ 90˚

INSTRUCTIONS FOR INSTALLATION AND USE OF THE MODEL #3503 8”x 60 DEGREE FIXE D PI T CH R O OFIN G BRAC K ET (F O R US E ON 21/12 PITC H ROOFS): CAPACITY: One worker per 8 feet of scaffolding plus 40 pounds of materials. GENERAL REQUIREMENTS: When installed,

the platform support arm must be set to match the pitch of the roof, allowing for the installation of a fully decked and level walk surface. MOUNTING THE ROOF BRACKET:

1) All brackets shall be attached to the roof with 20-penny nails. Use all slots on mounting plate. 2) Position bracket so that all nails penetrate both the roof’s surface and the rafter below. 3) Spacing between brackets shall not exceed 8 feet. INSTALLING PLATFORM: 1) wood platforms shall not be less than 2 inches nominal thickness and shall extend beyond the support arm not less than 6 inches and not more than 12 inches.

HEAVY DUTY ROOFING BRACKETS

INSTRUCTIONS FOR INSTALLATION AND USE OF THE MODEL #2502 & #3505 6” X 90 DEGREE & #3502 8”x 90 DEGREE FIXED PITCH ROOFING BRACKET (For use only as a slide guard or a material support): CAPACITY: 250 pounds of materials. GENERAL REQUIREMENTS: On roofs with

a 4/12 to 6/12 roof pitch, when installed as a slide guard, the scaffold brackets should provide a platform that is 90 degrees to the roof’s surface at a point along the eave of the roof. For roof slopes greater than 6/ 12 up to 8/12 additional 90-degree slide guards must be installed parallel to the rst row no further than every eight feet of roof slope. Additional fall protection methods are required on slopes 8/12 or greater. When slope is greater than 4/12 and the ground to eave height is greater than 25 feet slide guards should not be used. MOUNTING THE ROOF BRACKET: 1) All brackets shall be attached to the roof with 20-penny nails. Use all slots on mounting plate.

2) Position bracket so that all nails penetrate both the roof’s surface and the rafter below. 3) Spacing between brackets shall not exceed 8 feet. INSTALLING PLATFORM:

1) wood pla tform s shall not be less than 2 inches nominal thickness and shall extend beyond the support arm not less than 6 inches and not more than 12 inches. 2) Always use clear, straight-grained wood free from knots or defects.

3) If extende d leng th pla tform s are required, use additional Roof Brackets every 8 feet. 4) Secure to bracket by nailing the platform to the bracket using the hole provided in the platform retainer. INSTRUCTIONS FOR USE: 1) No more than one person shall occupy any given 8 feet of a Roong Bracket Scaffold.

2) Always use OSHA compliant fall arrest system, guard rails, catc h platforms or other safety equipment as required by Local, State or Federal OSHA Regulations. 3) Roof Brackets are intended for use by the experienced tradesman. 4) OS HA Regu lati ons req uir e that employers provide training in the use and care of this product. CARE

AND MAINTENANCE: 1) Inspect all Roong Brackets before each use to be sure that there is no damage or deformation, or deterioration from rusting. Discard if necessary. 2) Do not throw or drop from a building or onto a truck. 3) Do not use if exposed to extreme heat or cold. Discard at once. 4) Do not use if wet or frozen.

INSTRUCTIONS FOR INSTALLATION AND USE OF THE MODEL #2503 & #3506 6”x 60 DEGREE, #2504 & #3507 6”x 45 DEGREE, #2505 & #3508 4”x 90 DEGREE FIXED PITCH ROOFING BRACKET (For use only as a material support): CAPACITY: 250 pounds of roofing materials.. MOUNTING

THE ROOF BRACKET: 1) All brackets shall be attached to the roof with 20-penny nails. Use all slots on mounting plate. 2) Position bracket so that all nails penetrate both the roof’s surface and the rafter below.

2) Always use clear, straight-grained wood free from knots or defects. 3) If extended length platforms are required, use additional Roof Brackets every 8 feet. 4) Secure to bracket by nailing the platform to the bracket us ing th e hol e pro vide d in th e platform retainer. INSTRUCTIONS FOR USE: 1) Material supports are not intended for use as a scaffold or work platform.. 2) Always use OSHA compliant fall arrest system, guardrails, catch platforms or other safety equipment as required by Local, State or Federal OSHA Regulations. 3) Roof Brackets are intended for use by the experienced tradesman. 4) OSHA Regulations require that employers provide training in the use and care of this product. CARE AND MAINTENANCE: 1) Inspect all Roong Brackets before each use to be sure that there is no damage or deformation, or deterioration from rusting. Discard if necessary. 2) Do not throw or drop from a building or onto a truck. 3) Do not use if exposed to extreme heat or cold. Discard at once. 4) Do not use if wet or frozen.

PO Box 559 • Stoughton, MA 02072

Customer Support and Ordering Information

781-344-1000 • www.qualcraft.com