Qualcraft Cable Grab User Manual

®

ROPE and CABLE GRABS travel freely on 5/8” vertical
lifelines as a connector between the worker’s harness and the
lifeline. The inertia of a fall activates the locking device.

The back of this sheet contains instructions that must be retained
for OSHA compliance! Do not discard!

Guardian products meet and comply with all
applicable ANSI standards and OSHA regulations.

Manufactured with pride in the U.S.A. Kent, WA 98032 Ph:800-466-6385

Rope or Cable Grabs

Rope Grab for 5/8" Lifelines

01230

Cable Grab for 3/8" 7x19 aircraft cable

01260

Your Safety Company For Life

GF Ropegrab clamshell 4/29/02, 4:15 PM1

READ CAREFULLY BEFORE USING THE EQUIPMENT.

A copy of manufacturer’s instructions shall be provided to users before
equipment use begins. Users are required to have a rescue plan and the
means at hand to implement it when using this equipment.
Grabs are designed to act as fall arrestors via connection to an approved
lifeline system and full body harness.

Do not alter or misuse the equipment.

FOR PERSONAL FALL PROTECTION ONLY!

Do not use combinations of components or subsystems that may affect or

interfere with the safe function of each other.
Do not expose the equipment to chemicals that may produce a harmful
effect. Consult manufacturer in cases of doubt.

Do not use the equipment around moving machinery or electrical hazards.
Do not use soft goods around sharp edges or abrasive surfaces or loop

around small diameter structural members.

READ INSTALLATION INSTRUCTIONS BEFORE USING!

Grabs must only be used with compatible equipment. Must be attached to
approved lifelines. Maximum worker capacity is 310 lbs. Do not allow
more than a 6 ft.free fall distance unless system is designed specifically
for greater distance. Contact OSHA for specific guidelines.

PROPER USE:

For fall arrest, attach lanyard only to the dorsal D-ring located between
the middle of the shoulder blades on the harness. For ladder applications
grabs can be attached to an approved chest D-ring by using a carabiner.
Product Limitations include exposure to chemical hazards, corrosive
agents, abrasive surfaces, electrical hazards, excessive heat, and any other
element that might render the equipment unsafe. Never connect two
snaphooks directly to each other.

WARNINGS BEFORE USE:

When in use, do not move the unit by holding the body of the grab.
Holding the body of the grab it may restrain the locking mechanism,
rendering it unable to arrest the fall.
Grabs are designed for use in a personal fall arrest or restraint system
with a max. weight (person and equipment) of 310 Ibs. Attach only to
approved anchorage points and lifeline systems.

Never allow lifeline or grab to contact any outside objects during use.
Make sure that your path is free and clear of obstructions and hazards.

Positioning the rope grab above user on the lifeline minimizes falling
distance. Avoid swing falls by working directly below the anchor point
whenever possible.

DIRECTIONS FOR USE:

To open and close rope grab: Move the lever into the up position and

unscrew the knob. Wrap around rope making sure that the arrow on the
grab is pointing UP on the lifeline. Close the grab around the lifeline, put
the locking lever in the down position and tighten the keeper knob.
For cable grabs: Remove the locking pins and wrap the unit around the
lifeline, making sure that the UP arrow is facing up on the lifeline. Close
the grab around the lifeline and reinsert the pins.

Equipment should be inspected at least annually as a part of your regular

INSPECT EQUIPMENT BEFORE EACH USE!

safety program. Inspections should at the least include a check to see that
all of the components of the equipment are performing properly. Common
sense dictates procedures for visual inspections.
When inspecting equipment, check for physical deformations, excessive
wear, burns, cracks, corrosion, and that all components work properly and
safely. Inspect connecting hardware and webbing of any other system
components daily. If product fails inspection contact your local dealer or
Guardian for replacement information.

MAINTENANCE, CLEANING, AND STORAGE

Repairs to equipment can be made only by a Guardian representative or
person or entity authorized in writing by Guardian. Contact Guardian for
maintenance and repair.

Remove from service all products subjected to fall arresting forces.

Guardian will replace any of its components involved in a fall arrest.
Contact Guardian for policy specifics.
Cleaning after use is important for maintaining the safety and life of the
equipment. Cleanse the equipment of all dirt, corrosives, and contami­nants. If equipment cannot simply be wiped clean use a mild commercial
soap and water. Wipe and hang to dry.
Store equipment where it cannot be affected by heat, light, excessive
moisture, oil, chemicals, or other degrading elements.

USE ONLY 5/8 INCH (16MM) DIA. SYNTHETIC ROPE MIN.
BREAKING STRENGTH 6000 LBS. (26.7 KN)
MAX. 3FT. (.9m) LANYARD.
FAILURE TO READ AND FOLLOW INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH.

GF Ropegrab clamshell 4/29/02, 4:15 PM2