Installation Manual
This manual is aimed at a technical level reader who is expected to be familiar with all safety
precautions relevant to the use of electrical and electronic equipment.
This system operates with 48v DC power supply. To maintain warranty only Quail Digital
approved parts should be used. Do not attempt to power the Quail Digital Pro7 Headset
System using Power over Ethernet (PoE) adaptors, as they may cause damage to the Base
Station.
|page 2
Contents
System Overview 4
Q-P7BS - Pro7 Base 5
Q-P7HS - Pro7 Headset 7
Q-P7CH - Pro7 Charger 8
Q-P7MK12 - Pro7 12 Button Keypad 8
System Installation 9
Deciding how many Bases 9
Installation rules 10
RJ45 wiring 10
Remote registration switch 11
Registering the headsets 12
Locating the charger 12
Keypad installation 13
System Test 16
System Specification 18
|page 3
System Overview
Quail Digital Pro7 system is a DECT wireless headset system using multiple Bases Stations (Bases) to
cover large areas with up to 30 wireless headsets. Once the headsets are registered to the Base/s
they all listen and up to 6 users talk simultaneously.
The system allows the configuration of a large DECT wireless network, connected and powered via
Cat5 cable giving the flexibility to position Bases for wide area, multi-room, multi floor coverage. Up
to 20 bases can be deployed on the same network. Interconnecting Bases use Cat5 cable for power
and data transmission. The system can be used in conjunction with wireless keypads for transmission
of pre-recorded messages activated from keypads or other device to the headsets.
Keypads are mainly used at tills and call points in retail applications to transmit assistance messages.
All headsets hear all the messages.
The standard range for each base is 50 metres (150ft) from the Base inside and up to 100 metres
(300ft) in open spaces. Internal walls, partitions, building fabrics and ceiling heights can affect range.
|page 4
Q-P7BS - Pro7 Base Station
The Q-P7BS Base is a DECT wireless transceiver (license free) which is powered by an external 48 Volt
DC universal power supply. The Base can be networked with multiple Bases (20 max) using standard
Cat5 network cable and RJ45 connectors.
To connect Bases use the standard network configuration type B (see from page 9).
The 48 DC Volts is provided to the Base with the QD mains adaptor or from the network cable
connected on the RJ45 “A” socket.
The headsets need to pair with the Base(s). The pairing process is referred to as registration. Each
headset needs to be registered to the system. Headsets can be added or removed at any time by
going through the registration process (see page 12). When the registration process is completed
the network will automatically update the registry across all the Bases on the network.
There are two LEDs in the front panel of the Base which indicate its status at any time.
|page 5
Registration
Button
Cat5
Out
Cat5
In
Power
adaptor
Micro
SD card
Message
volume
For registration: press for 5 secs
To reset: press for 15 secs
Front
Power and Status LEDs
Base Station
Bottom
Top
Q-P7BS Base functions
Registration button and registration socket
This button allows you to put the Base into registration mode. Use a pencil or narrow tipped
screwdriver to activate the button in the housing of the Base. Press the registration button for 5 seconds
to enter this mode. Pressing the wall mounted registration socket for 5 seconds does the same.
Resetting the Base or network
The Base should be reset or ‘synchronised’ whenever additional bases are added or when the system
is reconfigured for any reason or when the SIMcard is updated. To reset the system pressing the
registration button on the master Base, or the wall mounted registration button for 15 seconds, which
resets the complete network. Don’t reset the Base by removing the power adapter, it will only reset
the bases supplied from that particular socket.
Micro SD card
This card is used to store the WAV audio files triggered by the remote keypads. For instructions on
recording the audio files, naming protocol and programming of the keypads refer to page 15. Only
use SanDisk MicroSD cards, formatted as Fat32, file size allocation 4096.
Keypad messages
The Base is fitted with an FM receiver for communication with the remote keypads. Up to 256 keypads
can work with one single base or network. For the recording of audio files, naming protocol and
programming refer to the system installation section.
Message volume adjustment
The volume adjustment is located at the bottom of the Base. This increases/decreases the audio
level of the messages played in the headsets. Use a thin flat tipped screwdriver and gently turn to
the right to increase the volume and to the left, to decrease.
RJ45 networking sockets
Use these two sockets on the top of the base to network two or more bases.
|page 6
POWER LED STATUS LED
B
ooting up
Base is master and ready
B
ase is slave and ready
S
ynchronization signal
receiving OK
Active call or calls on this
Base
BOTH LEDs FLASHING CORRECTIVE ACTION
Power too low to boot up Check the individual power supplies
o
n the network for possible failure; or
b
eing switched off; or consider adding
an extra power supply to the network
Base in registration mode The system will time-out of this mode in
10 minutes but you can press the
registration switch to exit the
registration mode manually
Q-P7HS - Pro7 Headset
The headset can be worn on either ear. The headset is available with a headband or neckband.
Volume: There are 5 volume settings. Use the toggle at the rear of the headset to adjust volume by
pressing upwards for each step.
Speech: The headset can be used in 2 speech modes, TalkLock, and PTT (push to talk).
TalkLock: This mode puts the headset in hands free mode. To activate, press the silver button for less
than 1 second, the headset is then hands-free, to deactivate it, press silver button again. This will shut
off microphone.
PTT: Press silver button while you are talking, release when finished.
Talk-lock feature
The user engages TalkLock mode by pressing ‘Page’ button for under a second. The headset will
remain in hands-free talk-lock mode until the ‘Page’ button is pressed again. The system reaches full
channel capacity when 6 users engage talk-lock. At full capacity, ie when 6 headsets are on
TalkLock, other headsets cannot enter a call. To ensure the system is operating efficiently it selfmonitors, and if it detects no voice activity for 5 minutes on a headset in talk-lock mode, it
automatically drops the TalkLock mode on the first headset to reach that condition freeing capacity
for all other users.
The table below shows the different audible tones for the different headsets status:
|page 7
Volume - slide up/down
Push to Talk switch
Battery - to remove the battery, hold the mic
boom firmly in your hand and slide the ear pad
and the battery towards the mic boom tip
STATUS TONE
Registration mode 1 beep every second
Out of range 2 beeps every 10 seconds
Battery low 3 beeps every 60 seconds
Registration complete 1 long beep (3 seconds)
Busy tone 3 long beeps
Headset not registered 1 beep every 3 seconds
Base capacity full As per busy tone
Call drop Bloop-bleep tone
Q-P7CH - Pro7 Charger
The system comes with an 8 port charger and
storage unit. This should be located within the
transmit range of the Base so that the headsets
log on to the network automatically when
they’re uplifted from the charger rack. If the
charger is located out of range of the Base, log
on will be delayed until the headsets are
carried into range. Note that headsets out of range of the Base will be de-registered if the registration
button is pressed. The charger should remain plugged in at all times, ideally on a 24 hour constant
supply to maintain charging. (See red LED on front surface).
When a headset is not in use it should be placed back into the charger/storage rack. Charge time
is approximately 2.5 hours to full charge. When headsets are charging the blue light on the headset
will flash every 5 seconds. When fully charged, the blue light is constant.
Headsets will last for up to 8 hours between charges, slightly less on TalkLock mode. 3 beeps every
60 seconds indicate that the battery is getting low and that user should swap headsets.
Q-P7MK12 - Pro7 12 Button Keypad
The wireless message keypad is a transmitter used for sending pre-recorded
voice messages to the headset wearers using a license-free FM frequency.
When a key is pressed, the message will go via the Base to each headset. Key
pads are powered by 2 x AA batteries. When a button on the keypad is
pressed the green transmit indicator flashes for 2 seconds. If the red LED is on,
the batteries need replacing.
Please refer to keypad installation section for more details on how to record,
name and store the files and how to program the keypads for the different
locations.
|page 8
Accessories
Neckband Q-RH7NB
Headband Q-RH7HB
Battery Q-RH7BAT
Power Adapter Q-48V
Headset Charger Shelf Q-P7SHELF
Hygiene Covers (box of 200) Q-RH7HC
System Installation
Before permanently installing the system, it is advisable to carry out a site survey by temporarily
placing the Base/s in different locations to optimize coverage. You should also identify power sockets
and cable routes for Cat5 if you intend to use multiple Bases.
Important Note: Power to the Bases should use a constant 24hr power outlet. If one or more mains
circuit is switched off it may affect the operation of the entire Base network.
The following cable and tools are required for any Pro7 network installation:
•
Cat5 cable
•
RJ45 plugs and crimping tool
•
LAN +RJ45 cable tester
It is important to check RJ45 connectors and cables with a LAN tester before connecting to the base
as the 48V DC could be introduced in the wrong pin causing possibledamage to the base or entire
network.
Deciding how many bases
Single Base installations
For small premises you may require just one Base. Try temporarily locating it in different locations to
check and optimise coverage. Use a registered headset to test audiable range. Before selecting
the final position, make sure there is power nearby. Recommended height of the Base is between 24 metres (6-12ft) from floor level.
On a single Base installation the LEDs on the front of the Base will show Power LED red and Status LED green.
If you are using remote keypads or other messaging device on the network the MicroSD card always
goes into the ‘master’ Base, remove the SD card from any secondary Bases.
Multiple Base installations
Larger sites need thorough planning for positioning of Bases. Using a registered headset and plugging
in Bases in temporary locations around the premises, experiment with the coverage. If you place
your ‘next’ Base 15 metres out of the range of the previous Base, you’ll be giving yourself plenty of
overlap coverage.
Once you’ve achieved the coverage you want follow the ‘installation rules’ on the next page. The
first Base you install in the line should be defined as the ‘master’. Consequent Bases in the network
become ‘secondary’ Bases and take their registration and synchronisation instructions from the
‘master’. The network identifies which Base is the ‘master’ because it’s the only one without an ‘IN’
Cat5 cable. You can identify which Base is the master because the power LED is RED. When wiring
consequent Bases note that the RJ45 cable goes to the ‘IN’ socket on the next Base and then
from the ‘OUT’ socket to the next Base’s ‘IN’ socket, and so on. You
can identify which Bases are ‘secondary’ because their power LED is GREEN.
Refer to the Installation rules section on maximum cable lengths between Bases, and the number of
Bases powered from a single source. Power can be supplied to the network from any of the Bases,
it does not have to come from the master. If you exceed the rules of either cable length or number
of Bases from a single power source you may find there’s insufficient power to activate the network.
|page 9
If both front panel LEDS on any Base are flashing orange it means there’s insufficient power to that
Base to boot up. Check cable, connector and power supply. If each of these is OK it indicates an
additional power source is required. If one or more additional power sources are added the Base
Status LEDs will change from flashing orange to solid orange indicating synchronisation with the
network. The LED will then turn solid green when synchronised.
The larger the network the longer it takes to boot up and synchronise the Bases. Allow up to 5 minutes
to synchronise larger systems.
Installation rules
a
Ideal height for Bases is between 2 and 4 metres (6-12ft) above floor level.
a
The maximum cable length between any two Bases should not exceed 100m (300ft).
a
The maximum cable length between two power sources should not exceed 200m
(600ft).
a
The maximum number of Bases a single power supply should support is four within
200m (600ft) overall cable.
a
When ‘mapping’ the premises, as a general rule, place the next Base 10m beyond
the point where the headset loses range from the previous Base.
a
Label the Cat5 cables that go into the top of the Base IN and OUT respectively to
avoid miss-connection at a later date.
a
Power to the Bases should use constant 24hr power outlet. If one or more mains
circuits are switched off, it may affect the operation of the entire network.
a
Always reset the network when you’ve completed the fixed part of your installation
to ensure proper synchronization between bases.
a
If you are using keypad messages, ensure there is only one micro SD card in the
network. Remove SD cards from any other bases.
RJ45 wiring
The cable that connects the base stations is a Cat5 UTP cable, with 4 pairs of conductors and RJ45
connectors at each end. The RJ45 plug at either end should have the following type B standard
wiring:
After crimping each plug it is important to use a network
tester to check its correct functionality before inserting it in
the base. If the color code is not correct it can cause
damage to the base.
It is also advisable to label the “IN” and “OUT” on each
cable to facilitate any future changes in the network.
|page 10
TYPE B STANDARD
Remote registration switch
The remote registration switch allows you to extend the ‘pin hole’
registration/reset switch on the base to a lower location to provide better
access to the user.
This switch is connected to the two screw
terminal connector located at the top of the
base and should be located just out of easy reach to avoid casual
pressing. Any 2-core cable can be used.
Please see pictures below showing how to open the remote
registration switch to make connections and locate it on the wall.
|page 11
1. Unclip cover 2. Remove 4 screws 3. Connect 2 wires to
switch terminals and fix
rear casing to the wall.
4m
2m
0m
Base
Registration
Button
Pin Wire colour Signal
1 W
hite-Orange
A
udio data Out +
2 Orange Audio data Out -
3 W
hite-Green
S
ynchronization signal +
4 Blue Audio data In +
5 White-Blue Audio data In -
6 Green Synchronization signal -
7 White-Brown GROUND
8 Brown POWER (+48V)
See wiring colour code below:
Registering the headsets
Before using the system each headset needs to be registered to the network. Thereafter, any new or
additional headset being added also has to be registered. The Pro7 Headset System can register up
to 30 headsets.
When registering one or more new headsets, follow this procedure
1 Make sure the new headset(s) has been in the charger and is fully charged.
2. Make sure all the headsets in use on the system are in range of of all the Bases on the network. If
a headset isn’t in range or has a missing or flat battery during the registration process it will be
deleted from the system. Headsets in a charger that’s in range of a Base do not need removing
from the charger during the registration process.
3. Enter the Base in registration mode either by pressing the registration button on the Base (bottom
face) or by pressing the remote registration switch on the wall for 5 seconds. Both LEDs will flash
green when the system is in registration mode.
4. Put new headset(s) only in registration mode by placing the headset on your right ear and
pressing large silver switch and volume toggle down for about 3 seconds. Wait for the blips to
change their frequency and tone to one blip every second.
5. A 3 seconds long blip signifies successful registration.
6. You may also hear a double blip tone that will indicate it is ready to use.
7. As soon as headset(s) is registered the system is ready to use. Press registration switch again to
exit registration process or leave it to time out after 10 minutes.
If there are multiple Bases on the network, the entire network will go into registration mode. This will
allow you to register the headsets from any location in the coverage area.
All consecutive Bases receive the registry of headsets from the master Base automatically.
Locating the charger
The Headset Charger should be positioned on a worktop and plugged into a socket that is a
constant 24hr power outlet. The charger should be located within range of a Base so that headsets
remain linked to the base/network at all times. The headsets do not need to be active on the charger
during the registration process but they do need to be within range to avoid being deleted duringt
the registration process.
Return headsets to the charger when not in use. Charge time is approximately 2.5 hours. When
charging, the blue light on the headset will flash every five seconds. When fully charged the blue
light is constant. Headsets will last up to 8 hours between charges, slightly less in TalkLock mode. 3
beeps every 60 seconds indicate the battery is getting low.
|page 12
Keypad installation
The Pro7 Headset System is available with a remote messaging facility using RF transmission keypads.
The keypad is battery operated; typically lasting in the region of 6 - 9 months. If batteries are supplied
with the unit, remove the battery housing cover and remove the battery saver leaf from the contact
terminal to begin using the keypad. There is no on/off switch - the keypads are powered all the time.
Install the keypad in the desired location. We recommend Velcro to attach the keypad to a flat
surface.
The keypads have a programmable location ID and 12 programmable button messages. You can
program the keypads by using the internal 8 way dip switches to for their ID and the 4 way internal
dip switches for the type of message and zone.
On the 8 way DIP switch, select the keypad “Address/ID” up to 256 different addresses can be
obtained. Each keypad, in an installation, should be programmed with a unique address. Refer to
keypad Binary Addresses for a list of the possible binary addresses.
On the 4 way DIP switch, switches 1 and 2 select the 'Zone' of the remote keypad. Up to 4 different
zones of keypads may be used in the same area. These switches are reserved for future usage and
therefore should always be off. Also on the 4 way DIP switch, switches 3 and 4 select the “Type” of a
remote keypad. Using a different type will cause a different set of audio messages to play when a
button is pressed.
Keypad Binary Addresses
The keypads use DIP switches to set their address, zone and type as described above.
All available addresses are presented on Table 1. The address DIP switches are numbered from 1 to
8 on the table and the same numbering appears on the keypad pcb whenever in Table 1 a “1”
appears the corresponding DIP switch should be on the ON position, otherwise it should be OFF
(opposite the ON label).
|page 13
Buttons Ba
nk
3 D
ip 4 D
ip
B
an
k 0
Off
Off
B
an
k 1
Off
On
B
an
k 2
On
Off
B
an
k 3
On
On
|page 14
A
ddress
D
IP Switches
1 2 3 4 5 6 7 8
0 0 0 0 0 0 0 0 0
1 1 0 0 0 0 0 0 0
2 0 1 0 0 0 0 0 0
3 1 1 0 0 0 0 0 0
4 0 0 1 0 0 0 0 0
5 1 0 1 0 0 0 0 0
6 0 1 1 0 0 0 0 0
7 1 1 1 0 0 0 0 0
8 0 0 0 1 0 0 0 0
9 1 0 0 1 0 0 0 0
10 0 1 0 1 0 0 0 0
11 1 1 0 1 0 0 0 0
12 0 0 1 1 0 0 0 0
13 1 0 1 1 0 0 0 0
14 0 1 1 1 0 0 0 0
15 1 1 1 1 0 0 0 0
16 0 0 0 0 1 0 0 0
17 1 0 0 0 1 0 0 0
18 0 1 0 0 1 0 0 0
19 1 1 0 0 1 0 0 0
20 0 0 1 0 1 0 0 0
21 1 0 1 0 1 0 0 0
22 0 1 1 0 1 0 0 0
23 1 1 1 0 1 0 0 0
24 0 0 0 1 1 0 0 0
25 1 0 0 1 1 0 0 0
26 0 1 0 1 1 0 0 0
27 1 1 0 1 1 0 0 0
28 0 0 1 1 1 0 0 0
29 1 0 1 1 1 0 0 0
30 0 1 1 1 1 0 0 0
31 1 1 1 1 1 0 0 0
32 0 0 0 0 0 1 0 0
33 1 0 0 0 0 1 0 0
34 0 1 0 0 0 1 0 0
35 1 1 0 0 0 1 0 0
36 0 0 1 0 0 1 0 0
37 1 0 1 0 0 1 0 0
38 0 1 1 0 0 1 0 0
39 1 1 1 0 0 1 0 0
40 0 0 0 1 0 1 0 0
41 1 0 0 1 0 1 0 0
42 0 1 0 1 0 1 0 0
4
3
1 1 0 1 0 1 0 0
44 0 0 1 1 0 1 0 0
45 1 0 1 1 0 1 0 0
46 0 1 1 1 0 1 0 0
47 1 1 1 1 0 1 0 0
48 0 0 0 0 1 1 0 0
49 1 0 0 0 1 1 0 0
50 0 1 0 0 1 1 0 0
5
1
1 1 0 0 1 1 0 0
52 0 0 1 0 1 1 0 0
53 1 0 1 0 1 1 0 0
54 0 1 1 0 1 1 0 0
55 1 1 1 0 1 1 0 0
56 0 0 0 1 1 1 0 0
57 1 0 0 1 1 1 0 0
58 0 1 0 1 1 1 0 0
59 1 1 0 1 1 1 0 0
60 0 0 1 1 1 1 0 0
61 1 0 1 1 1 1 0 0
62 0 1 1 1 1 1 0 0
63 1 1 1 1 1 1 0 0
64 0 0 0 0 0 0 1 0
65 1 0 0 0 0 0 1 0
66 0 1 0 0 0 0 1 0
67 1 1 0 0 0 0 1 0
68 0 0 1 0 0 0 1 0
69 1 0 1 0 0 0 1 0
70 0 1 1 0 0 0 1 0
71 1 1 1 0 0 0 1 0
72 0 0 0 1 0 0 1 0
73 1 0 0 1 0 0 1 0
74 0 1 0 1 0 0 1 0
75 1 1 0 1 0 0 1 0
76 0 0 1 1 0 0 1 0
77 1 0 1 1 0 0 1 0
78 0 1 1 1 0 0 1 0
79 1 1 1 1 0 0 1 0
80 0 0 0 0 1 0 1 0
81 1 0 0 0 1 0 1 0
82 0 1 0 0 1 0 1 0
83 1 1 0 0 1 0 1 0
84 0 0 1 0 1 0 1 0
85 1 0 1 0 1 0 1 0
86 0 1 1 0 1 0 1 0
87 1 1 1 0 1 0 1 0
Creating Audio Files
The audio files must be *.WAV files encoded in mono u-law at 16 kHz. This is easily achieved with
freeware software like MediaHuman Audio Converter, Fre:AC, Audacity or SoX.
N
aming the Audio Files
T
wo different files can be used to play a complete audio message, the file naming scheme for those
f
iles is as follows:
K
eypad ID files: id-xxx-#.wav
Where xxx is the keypad address/ID setting from 0 to 255 and # is the keypad type setting from 0
to 3 (i.e. there can be 4 different sets of ID messages using type 0-3).
Button Pressed files: but-xx-#.wav
Where xx is the button number from 1 to 12 and # is the keypad type setting from 0 to 3 (i.e. there
can be 4 different sets of button messages using type 0-3).
How the Audio files are played
There is a distinction on which files are played based on their address/ID:
Keypads whose address/ID is between 0 and 199, will play files as follows:
Play the ‘Keypad ID’ file that matches the keypads address/ID followed by the ‘Button Pressed’
file that matches the keypad button number pressed
Keypads whose address/ID is between 200 and 255 files are played back as follows:
Play the ‘Keypad ID’ file that matches the keypads address/ID
This distinction allows special/custom messages to be played in keypads whose address/ID is above
200.
How the Audio files are stored
Audio files are stored on a Micro SD memory card which is inserted on the SD card slot at the bottom
of the base. Any micro-SDCard currently available on the market should work as long as it is correctly
formatted as a FAT32 file system with default settings.
To update or copy the audio files to the SDCard, simply insert the micro-SDCard into an SDCard
adapter connected to a PC and it will usually appear as a new disk drive in Windows Explorer format
it using FAT32. Copy the files onto the drive. Do not use folders, simply put the files directly into the
root directory of the drive. When the files have been copied you will usually need to stop the card
using the Windows ‘Unplug or Eject Hardware’ function.
Before inserting the memory card in the system please follow these rules:
a
When inserting the micro-SDCard, the system always has to be powered down.
a
On booting up, the system will detect which base has the micro-SDCard and inform every
other base of the micro-SDCard holder address.
a
After the system attributes the micro-SDCard holder address, the micro-SDCard cannot be
changed to other base. If it is changed, the system will not be able to play messages.
a
You can remove and reinsert the micro-SDCard holder address, as long as it is reinserted in the
original base.
|page 15
a
If you want to reinsert the micro-SDCard in a different base, is it mandatory to reset the whole
system to have message playing capabilities.
a
The network will not boot up if there is more than 1 micro-SDCard inserted in the system.
Keypad messaging trouble shooter
IMPORTANT NOTE: Do not insert or remove the SD card while Base is ON. If you do, it will corrupt the
SD card and will require reformatting and copying the files.
|page 16
PROBLEM CHECK
Messages not playing
Base volume setting
Make sure keypad is within range of the base/s
Check transmit led on the keypad flashes when pressing any
button
Keypads batteries are fitted and full charged
Format SD as FAT32 and copy the files again
Check file type is WAV and not MP3
Check correct naming of the files
Button ID message playing only
Make sure ID dip switches inside the keypads are set to the right
address
Check correct naming of the files
System Test
Once all bases are installed, reset the system to synchronise the bases. Then register the headsets.
1. All headsets are registered and audio is ok
Collect all registered headsets and one by one, press the ‘Page’ button while talking to confirm
that you can hear your own voice. Repeat this step on all registered headsets.
2. Check coverage
Take a headset and place it on TalkLock. Whilst talking on the headsets, walk around the entire
area you wish to cover noting any blind spots. The audio should be clear and free of drop out.
The side tone on the headset enables you to hear your voice broadcast so you can carry out this
exercise yourself. When you walk from the zone of one base to the zone of another, you will see
the Status LED blinking GREEN as the call is active on that particular base.
3. Check all bases and handover
Walk around with all headsets on standby mode. As you stand in front of each base, press “page”
on one of the headsets and make sure that the Status LED starts blinking GREEN on the base you’re
nearest to. Then check the audio on the headset. Come out of talk mode and take a second
headset to repeat the same operation. Follow the same sequence and go through this procedure
on all the headsets for each Base installed.
4. Check remote registration switch
If the remote registration wall button is installed, while wearing a headset activate both of its
functions. For registration, press for 5 seconds seconds you will hear 2 bleeps in your ear to confirm
registration is in process. For reset, keep pressing for 15 seconds you will see the power LED on the
Base turns orange>green.
5. Check remote keypads
While wearing a headset, press all buttons on all keypads installed with a minimum of 5 seconds
between presses to make sure that you hear all messages. If presses are too fast (below 3 seconds)
the press will be ignored. Pay attention at the ID or location messages making sure that the right
keypad is placed in the correct location.
|page 17
|page 18
Base Station Q-P7BS
Operating frequency
1.88GHz-1.90GHz EMEA, Asia
1.910 GHz-1.930 GHz North America
Dect Transmission power
250 mW EMEA
125 mW North America
Mounting/recommended operating height 3 metres
Multi-base expansion detail (inc max) Network via Cat5 cable and up to 20 Bases
Multiple base data update procedure SD card
Expansion using CAT5 cable.
Max length + supplementary power
max 100 m cable length between Bases
Facilities messaging Keypad messages with volume adjustment
Power requirements 100-240v AC voltage sensing (mains cable supplied)
Dimensions 170 x 130 x 35mm
Weight 200g
Registration process Wireless pairing
Volume adjustment Inbound messages
SD card Audio messages storage
Capacity of headsets
Up 30 headsets all listening with a max of 6
simultaneous participants
Front display LEDs
Power LED
Solid orange Booting up
Solid red Base is master and ready
Solid green Base is secondary and ready
Status LED
Solid green Synchronization signal received OK
Blinking green Active call or calls on this Base
Power & Status LEDs
Flashing red Power too low
Flashing green Base in registration mode
Wall-mounted registration point Yes
System Specification
|page 19
R
egistration Button Q-P7RS
O
rdered Separately
Wall mounted switch to allow lower level
r
egistration activation
Dimensions 52 x 63 x 87mm
W
eight
1
00g
Headset Q-P7HS
Operating frequency
1.88GHz-1.90GHz EMEA, Asia
1.910 GHz-1.930 GHz North America
Operating modes TalkLock and PTT facilities as standard
Audio prompts
Registration mode 1 beep every second
Out of range 2 beeps every 10 seconds
Battery low 3 beeps every 60 seconds
Registration OK 1 long beep (3 seconds)
Busy tone 3 long beeps
Headset not registered 1 beep every 3 seconds
Registry full as per busy tone
Call Drop ‘bloop-bleep’ tone
Battery capacity 8 hours PTT, 6 hours TalkLock
Charge time 2.5 hours
Volume adjustment 5-stage, slide button up/down
Battery type - part number Lithium Ion 3.7v - Q-RH7BAT
Weight 50g
Headband - part number Q-RH7HB
Neckband - part number Q-RH7NB
Microphone type (noise cancelling) Noise cancelling electret mic
|page 20
8
Port Charger Q-P7CH
C
harge mode
F
ast charge
Mounting Desktop mounted only
Power requirements 12v external power supply (supplied)
P
ower supply part no
Dimensions 110 x 390 x 100mm
Weight 1200g
LED mode of headsets in charger
Blinking - charging
Permanent - charged
Keypad Messaging Q-P7MK12
Operating frequency 433 MHz
Power requirements 2 x AA cells (not supplied)
Dimensions 69 x 142 x 25mm
Weight 150g / 200g with batteries
Range 100m
Max qty on system 256
LED modes
Green flash - message transmitted OK
Red flash - battery low
92 Lots Road, London SW10 0QD, UK
T +44 (0)20 7349 2000
www.quaildigital.com
18.06.14
IC ID: 6402A-Q-P7BS
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
FCC ID: UDD Q-P7BS
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any inter ference received, including interference that may cause undesired
operation.
Loading...