What’s Included:
QuadLink 4-Station
[2]
Charger Multiplier, XC-QL4
2-Station Battery Maintenance
[1]
Charger, X2
X2-QL4-K2, 8-Station QuadLink Kit
Quick Start Instruction Manual
2-pin
output connect
2-pin
input connect
Battery Tester, XC-822-TEST
[1]
2’ Battery Leads with
[2]
Clips, XC-CLIPS
2’ Battery Leads with
[10]
Lugs, XC-LUGS
5’ Battery Extension
[8]
Lead, XC-EXT-5
2-pin
output connect
Status Indicators
QuadLink
2-pin
input connect
Xtreme 2-Station 12V
Maintenance Charger
Battery State of Charge
25’ Battery Extension
[4]
Lead, XC-EXT-25
PulseTech Products Corporation • 1100 South Kimball Avenue • Southlake, TX 76092-9009
800-580-7554 • ppc@pulsetech.net • www.pulsetech.net
X2-QL4-K2, 8-Station QuadLink Kit
Quick Start Instruction Manual
This Quick Start Instruction Manual is designed to help you quickly set up
and use your 8-Station QuadLink Kit correctly. It is not intended to serve as a
replacement for the product manuals themselves.
(1) Turn off engine if battery is still connected.
(2) Take the battery tester and remove the black negative (- NEG) probe from the tester (Fig. 1)
(3) Touch the red positive (+POS) probe to the (+) battery post.
(4) Then touch the black negative (-NEG) probe to the negative battery post.
(5) The battery tester’s LED will indicate the battery’s state of charge (100%, 75%, 50% or 25%.)
(6) If battery state of charge is 75%, 50%, or 25% go to step 7. If state of charge is 100% go to step
12. All batteries should test at 100% prior to being connected to the QuadLink(s).
(7) Connect the battery charger’s 2-pin output connector to the 2-pin input connector of either the
battery clips or lugs. (Fig.2)
(8) Attach the red positive (+POS) battery clip or lug to the (+) battery post.
(9) Attach the black negative (-NEG) battery clip or lug to the (-) battery post.
(10) Plug battery charger into 110-220 VAC power source.
(11) Charge battery until it’s fully charged. This is shown by the green “100%” LED illuminating.
(12) Connect your battery charger’s 2-pin output connector to the 2-pin input connector of the
QuadLink. (Fig.2)
(13) Connect the QuadLink 2-pin output connector to the 2-pin input connector of either the battery
lead with lugs or battery lead with clips.
(14) Connect the lugs or clips to the battery. Be sure to first connect the red battery clip or lug to the
(+) battery terminal. Then connect the black battery clip or lug to the (-) battery terminal.
(15) Repeat as necessary for up to 8 batteries.
(16) Once all cable leads have been connected to all the batteries, plug battery charger into 110-220
VAC power source.
(17) Your 8-Station QuadLink Kit can remain connected indefinitely without danger of overcharging
or overheating. Continued use will ensure existing sulfates on the battery plates are eliminated
and will prevent new sulfate crystals from forming allowing your battery to charge deeper,
maintain greater reserve capacity and last longer.
Fig. 1 Fig. 1
998XM206 05/13
By
Model X2 12-Volt Charger
FEATURE AND USE GUIDE
Model X2 12-Volt Charger
FEATURE AND USE GUIDE
Table of Contents
Use Guide...................................................................1
Specifi cations............................................................3
Five-Year Limited Warranty........................................4
Accessories...........................................................Back
FEATURES
Pulse
Desulfate
Test
Charge
Patented Pulse Technology increases the duty and life cycles of all 12 volt
batteries by up to five times
The unique application of patented PULSE conditioning provided by
Pulsetech
type of 12V lead-acid battery by minimizing the size of damaging lead sulfate crystals
Xtreme Charge
it continually to determine the appropriate charge rate based on your battery’s current capacity and condition. This TEST step also includes a “Bad
Battery” indication if it determines the battery is faulty and cannot be recharged.
A proprietary microprocessor controlled integrated charging process
measures both voltage and current and applies only the amount of charge
your battery is able to accept at any given time. As the patented pulse
technology is applied in combination with the saturation charge the battery’s condition improves. This proprietary process inhibits and removes
sulfation, protects your battery from overcharging and extends its operating life.
®
Products increases performance and life cycles of any size or
®
evaluates the battery during initial connection and tests
Charge
The X2 is also designed to be a MAINTENANCE charger for any type of
12-volt lead-acid battery. Through application of our proprietary charge algorithms and high frequency pulsing processes, your battery is maintained
safely at its proper operating voltage indefi nitely. If the charger is connected to a discharged battery, its BULK charge capability (2.5 A actual/5 A
effective) will re-charge the battery rapidly and safely so it can be put back
into service quickly.
USE GUIDE
Do not operate without first reading the Important Safety Instructions.
Connect red battery clip to positive (+) battery post. Then connect black
battery clip to negative (-) battery post.
Once you’ve connected the battery cables properly, you can begin the
charging process. Plug Xtreme Charge® into 110-220 VAC power source.
TEST
Green “On” light illuminates, indicating charger is
receiving proper ac input. If it’s connected to battery
correctly, red “Test” LED lights, indicating unit is
testing battery’s condition.
FAULT CONDITIONS
If red “No Connection” light illuminates, charger is
not connected to battery, or inline fuse on positive
battery lead needs to be replaced.
Should all the lights flash on and off and an audible warning buzzer be heard, battery clamps are
connected in reverse. Refer to Safety Instructions
booklet for detailed procedures to make sure leads
are connected properly.
If red “Bad Battery” LED lights, Xtreme Charge
is connected to a 6V battery or a 12V battery that is
®
below 7 volts.
1
CHARGING CONDITIONS
Once charger has evaluated battery’s current
condition, “Test” light goes off. The appropriate
charge profile begins automatically.
Green “Charging” light indicates Xtreme Charge®
is providing bulk charge to battery.
Three green “Pulsing” LEDs light sequentially
as charger conditions battery. Patented Pulse
Technology enables it to accept and maintain its
maximum charge.
During “Test” cycle, charger determines battery’s
state of charge and illuminates the appropriate light:
“25%,” “50%,” “75%” or “100%.”
After battery is charged fully, green “100%” light
illuminates, and “Charging” light goes off. This indicates charger is providing float charge to battery.
It may now be placed into service or left on the
Xtreme Charge® indefinitely to maintain peak condition.
If battery has been pulsing and charging for 24
hours continuously without reaching 100% state
of charge, unit discontinues charging. Red “Bad
Battery” light illuminates, indicating the battery is
non-rechargeable.
PULSE TECHNOLOGY
The unique application of patented PULSE conditioning provided by
Pulsetech® Products increases performance and life cycles of any size
or type of 12V lead-acid battery by minimizing the size of damaging lead
2
sulfate crystals. This allows your battery to accept more power than other
chargers can provide. Our patented PULSE technology is NOT “Pulse
Charging” which is commonly used in the market place today. It IS a totally unique 1-2 punch provided by the independent application of our unique
high frequency conditioning pulse on one circuit and proprietary charging
algorithms on another. This helps ensure that your new batteries will stay
in like-new condition while your older batteries often improve dramatically.
24 VOLT SYSTEM USE
Many 24 volt battery systems are composed of two (2) 12V batteries. These
two batteries are connected “in series.” These systems are often used with
heavy-duty, industrial or alternate energy applications. The Xtreme Charge®
X2 is a great solution for 24 volt systems because each battery is charged
and maintained independently. The X2 will test, charge, pulse and maintain
each battery for longer useful life and optimal performance. You may leave
the batteries connected in series (24V) without concern that the charger
will be damaged by 24 volts. The X2 will not be damaged by these 24 volt
systems and the X2 will not damage batteries, no matter how long it stays
connected. Connection to each battery is easy with heavy duty lugs or
spring clips (two sets of each are included with the X2).
SPECIFICATIONS
Xtreme Charge® X2 includes charger with 2 sets of fuse-protected quickdisconnect battery clamps and lugs, Important Safety Instructions and
Feature and Use Guide.
Charge Output Channels - 2
Internal Power Supply - 2 Fully Independent
Input Voltage - 100 - 250 V AC
Maximum Charge Current - 2.5A (5.0 Effective) per channel
Nominal Float Voltage - 13.6V per channel
Maximum Bulk Charge Voltage - 14.8V per channel
Pulse Frequency - 40-50 kHz per channel
Functional Output Cable Length - 8’ per channel
Agency Listing - CUL Approved
Housing - Weatherproof Rubberized base
3
FIVE-YEAR LIMITED WARRANTY
PULSETECH® PRODUCTS CORPORATION
®
XTREME CHARGE
What Does This Warranty Cover? This warranty covers any defects in workmanship or
materials in this charger under normal use and service.
How Long Does the Coverage Last? This warranty runs for five (5) years from the date of
purchase.
What Will PulseTech Do? PulseTech will, at its option, replace or repair any defective unit
with a new or rebuilt unit at no charge.
What Does This Warranty Not Cover? This warranty applies only to the battery charger.
This warranty does not cover any other equipment, static damage, water damage, overvoltage damage, dropping unit or damage resulting from extraneous causes including owner
misuse. In addition, PulseTech will not be responsible under this warranty if PulseTech determines that (1) upon examination that the circuit board failure was (A) caused by misuse,
neglect, accident, alteration or abnormal condition of operating or handling (including the failure to install the product in accordance with PulseTech’s instructions and observe the warnings in the Feature and Use Guide and the Important Safety Instructions) or other conditions
beyond the control of PulseTech or (B) damaged in transit to PulseTech, and (2) the owner
is not the original purchaser that purchased the product through an authorized PulseTech
dealer or distributor. This warranty is void if owner attempts to disassemble the unit or to
modify the cable assemblies. IN NO EVENT SHALL PULSETECH BE LIABLE FOR ANY
DIRECT, SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL, PUNITIVE OR EXEMPLARY
DAMAGES, EXPENSES, LOST SAVINGS OR LOST PROFITS OR ANY OTHER DAMAGES OF
ANY KIND FROM ANY BREACH OF THIS WARRANTY OR OTHERWISE. Some states, provinces or countries do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation may not apply to you.
BATTERY MAINTENANCE CHARGER
How to Get Service? Contact PulseTech by calling 1-800-580-7554 for a Return
Authorization Number. Then send the product postage prepaid with proof of purchase
(sales receipt) within the warranty period to PulseTech. Battery chargers beyond the warranty period are subject to the repair charges in effect at that time.
How Does State, Province or Country Law Apply? This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state, province to
province or country to country.
THIS WARRANTY IS THE SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER
WARRANTIES EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
Model X2
Southlake, TX 76092
U.S. Patent No. 7,834,592 B2
4
Additional U.S. patents pending
5
PRODUCTS &
By
By
ACCESSORIES
12V Xtreme Charge
®
w/Pulse Maintenance
Ideally suited for AGM and
Maintenance-Free batteries.
Increases the duty and life
cycle of all 12V batteries up
to five times longer.
Part #: 100X010 Model: XC100-P
12V 2-Channel Charger
w/Pulse Maintenance
Double the charging capabilities of the popular
XC100-P Xtreme Charge®
12V Battery Charger. Each
station charges at a 2.5 A
(5 A effective) charge rate at over 14.8 V.
Part #: 100X200 Model: X2
QuadLink®
4-Channel Battery
Charger Multiplier
Gives your existing 6V or
12V charger, no matter what the
brand, the ability to charge up to FOUR batteries at once.
Part #: 100X004 Model: XC-QL4
Battery Lead with Clips
This 7.5-amp fuse-protected
cable is supplied with a quickdisconnect terminal. Lead is 2
feet long.
Part #: 100X827 Model: XC-CLIPS
“Leave-On” Battery
Quick Mount Wall Bracket
Black powder coated 20-gauge
steel. “Quick Mount’ flex design
for easy clip in and out use. Clip into
the wall bracket for shop use or un-clip it and
take it with you as needed. For XC100-P only.
Part #: 100X808 Model: XC-QM
Full Enclosure Wall Bracket
Black powder coated 16-gauge
steel full enclosure designed to
suit heavy-duty, semi-permanent mounting requirements as needed. For XC100-P only.
Part #: 100X810 Model: XC-BKT
25’ Extension Lead
Extend a standard lead by 25
feet with this extension. It features quick-disconnect terminals on both ends. Lead is 25 feet long.
Part #: 100X825 Model: XC-EXT-25
Lead with Lugs
Xtreme Charge® 7.5-amp
fuse-protected cable comes
with a quick-disconnect terminal. Lead is 2 feet long.
Part #: 100X830 Model: XC-LUGS
Quick Battery Tester
Assess your 12-volt battery’s
health quickly with this pocketsized tester. It will be the most
used tester in shops, garages
and any areas where battery
checks are performed.
Part #: 100X822 Model: XC822-TEST
To purchase any of these
items, contact an authorized
®
Xtreme Charge
www.PulseTech.net or call
800-580-7554.
dealer, visit
998XM202 04/12
FEATURE AND USE GUIDE
Model XC-QL4 4-Channel 6/12V DC Charger Multiplier
Model XC-QL4 Feature and Use Guide
Table of Contents
Features .................................................................... Inside front cover
User Guide ............................................................................... 1 – 3
Specifi cations ......................................................................................3
Battery Charger Use..........................................................................3
FAQs ...................................................................................................... 4
5-Year Limited Warranty...........................................Inside back cover
Xtreme Charge
®
Products and Accessories..............................Back cover
Features
Thank you for your purchase of the Xtreme Charge® QuadLink® from PulseTech®
Products Corporation.
PulseTech® Products Corporation (www.PulseTech.net) is nationally recognized for
its innovative technologies specifi cally designed to improve 6/12V battery performance, trim replacement costs by extending battery life cycles and contributing to
the nation’s environmental movement to think and act Green by keeping batteries
healthy and out of the waste stream, landfi lls and smelters.
With the development of the QuadLink, Xtreme Charge® has multiplied this useful
application by 4 times—turning any 6V or 12V DC battery charger (using the standard 2-prong output connector) into a 4-station maintenance charger.
There’s no more need to spend time or to remember to switch back and forth
between vehicles or batteries in storage. Utilizing a simple, plug and play system,
QuadLink automatically splits and distributes 10-minute charge segments to up to
four batteries.
Applications include a wide variety of vehicles and equipment, including automobiles,
light trucks, SUVs, motorcycles, motor homes, small boats and watercraft, lawn
mowers and equipment, ATVs and even golf carts. When mated with a typical
maintenance charger (see User Guide) the QuadLink’s microprocessor automatically
adapts to the number of batteries actually connected.
Included with your QuadLink purchase:
1 – QuadLink 4-station charger multiplier
4 - Eyelet lug adaptor cables
4 - 5' extension leads
(Additional 5' and 25' lead extensions available separately)
User Guide
1
Do not operate without fi rst reading these important safety notices and use instructions.
Additionally, do not use this without fi rst reading important safety notices and use
instructions that come with your battery charger/maintainer and your battery.
NOTE: As part of good safety routine, this product is designed for use only with automatically controlled
charger maintainers and is optimized for use with the Xtreme Charge family of products. It is not
suggested for use with manual maintenance chargers that cannot be used without constant supervision.
1. Inspect all cable leads and connections to be sure that they are all in good working condition. Never use cable leads or clips that are worn, damaged or frayed in any way. Replace
worn or damaged leads prior to use. Do not alter or otherwise modify cables as this could
cause an unsafe condition possibly resulting in personal injury, explosion or fi re.
2. Connect the output of your battery charger/
maintainer to the input of the QuadLink.
Note: The charger must have the same industry
standard 2-prong connector to mate properly
with the QuadLink.
3. Connect the extension leads that come with the QuadLink to either the standard attached
battery eyelet connector on each vehicle battery and/or to the charging clip set that comes
with your charger. Be sure to fi rst connect the red battery clip to the positive (+) battery
terminal. Then connect the black battery clip
to the negative (-) battery terminal. Also, be
sure to double check that your attached eyelet
terminal cable sets are properly polarized.
Once you have connected the cable leads to
all batteries in use, you can begin the battery
maintenance process by plugging in your
charger to your AC power source.
4. What is happening:
A. Your battery charger is still in full control of the charging processes. Always refer to the
battery charger manufacturer’s instructions or the user interface on your charger to
determine what state of charge your battery is in.
B. The QuadLink is almost transparent to the battery. It does not add to the charging
capabilities of your charger, just to the number of batteries being maintained. Your
charger is still the “brain” in the system.
2
C. A blinking green LED light will indicate the fi rst battery
connected to the QuadLink. Once additional batteries are
connected, a solid glowing green LED light will verify
connection to all additional connected stations. Once the
charger is connected to the QuadLink and plugged into the
AC power source, the charging cycle begins. From this point
forward, the station or battery that is currently “live” or
being charged is indicated by a blinking green LED light.
D. Every 10 minutes, the QuadLink will switch to the next battery in line. If there is no
battery connected to any given channel, the channel will be skipped after a short qualifi cation process.
E. Cycle rotation will continue indefi nitely, maintaining the
charge of all 4 batteries for you automatically. The
QuadLink distributes your charger’s full power, moving
from battery to battery in 10-minute increments.
F. If you would like to remove a battery from the chain, it is
always best to unplug the QuadLink from the charger and
the charger from the AC power source fi rst. Once the battery
is disconnected and the units are plugged back in, the
QuadLink will reset and recognize the batteries in the circuit
and skip any open channels after a circuit verifi cation test.
G. If you replace or add a battery to an open channel, again it is always best to unplug
the QuadLink from the charger and the charger from the AC power source fi rst. Once
you have connected the new battery to the circuit and plugged the units back in, the
QuadLink will reset and recognize the additional battery in the circuit and begin the
process again.
Use Comments and Suggestions:
1. If you are putting a vehicle/battery away for an extended period, it is always best to give
the battery a good charge on its own for a few days and test it prior to putting it away for a
season or any extended period. This will assure that proper storage maintenance will occur
without a hitch.
2. If there is ever a power outage, it is likely that during the outage, the charger may and the
QuadLink will consume a small amount of power via LED light indication of the batteries’
state of charge and channel indication. This is common and will not cause noticeable discharge of the batteries in the circuit unless the power is out for an extended period of time.
Note: If either AC input power to the charger or DC power from the charger to the QuadLink
is purposely disconnected for any extended period for any reason, disconnect the QuadLink
from the batteries in the circuit until power is restored. This will assure that the batteries are not
unintentionally discharged.
3. If for any reason the QuadLink is not unplugged from the DC power source and allowed
to reset during removal of a battery, the LED channel indicator will remain illuminated
until the next cycle provides a circuit verifi cation test indicating an open circuit. The output
previously associated with the removed battery will then in turn be skipped.
4. For use more customized to your specifi c needs, including additional 5' extension leads
(part #100X805) and 25' extension leads (part #100X825), please visit www.PulseTech.net.
Additional Functionality:
The QuadLink is also uniquely designed to
provide a very useful service of maintaining the
state of charge of multiple 6V or 12V batteries
in 24, 36 and 48V series connected confi gurations typically used in Golf Carts or similarly
designed vehicles or battery packs.
The user would simply connect each output
lead using the provided eyelet lug connectors
(up to 4) to each of the 6V or 12V segments of
the multiple battery confi gurations and in doing
so allow the QuadLink to maintenance charge
each of the 6V or 12V segments of the pack in
10-minute intervals. This will ensure that the
entire pack is maintained at the state of charge
that they were left at when stored or left unused
for an extended period.
Specifi cations
Battery
Charger Use
Description: 4-channel 6/12V DC Char-
ger Multiplier
Input Voltage: 4Vdc to 18Vdc
Input Amperage: 8A Max
Functional Output Cable Length: 5'9"
(per channel) Note: Additional 5' and 25'
cable extensions available separately
Mounting: Yes, via 4 holes in housing
(use housing to mark holes on
mounting surface)
IMPORTANT: Please follow the use
and safety recommendations that were
included with the maintenance charger that will be used with your new
QuadLink. This information should
provide explicit important safety,
operation and maintenance instructions for the user, and, if applicable,
with assembly, moving and storage
instructions.
3
24V
36V
48V
4
Frequently Asked Questions
1. Can the QuadLink be used with a Solar Charger? YES, if the Solar Charger uses the same connector, is 6V or 12V
DC and does not exceed 8 Amp output.
2. Is the QuadLink water resistant? YES, it is water resistant but not waterproof. It cannot be submerged or left in
pooled water or driving rain. Safety dictates that one should never use an electrical product in wet conditions.
3. Does the “bad battery” function still work when using the QuadLink? The QuadLink is not a charger but a
charge conduit. If your charger has a “bad battery” indicator, it will work through the QuadLink connection.
4. Will the QuadLink work if batteries are connected to fi rst, second, and fourth outlet, skipping the third
position? YES, the QuadLink will sense the open circuit and skip it after a few seconds.
5. Will the QuadLink work on multiple battery types and styles simultaneously? For instance, AGM and Gel or
Deep Cycle marine and small Motorcycle batteries all connected to each of the 4 stations? YES, your charger
is still the “brain” in the system. If your charger has the ability to properly charge all of these battery types automatically, the QuadLink will allow it. If your charger has to be manually switched to alternate settings to enable proper
charge output for these different battery types, the answer would be NO. If this is your situation, we suggest using
the Xtreme Charge to charge multiple battery types automatically.
6. Knowing that the QuadLink is optimized for use with the Xtreme Charge battery charger; does it also work
with other brands of chargers? YES, as long as your charger is fully automatic and utilizes the same DC connector.
7. When connected to Gel, maintenance free and AGM battery with a charger that requires the use of a battery
selection dial for charging different battery types, what happens? We suggest that you do not use the QuadLink
with this type of charger. Consider buying an Xtreme Charge to properly charge all these types on the QuadLink automatically.
8. If there is no battery connected, is power fl owing to the battery clips or eyelet connector? The answer is NO
if you are using a fully automatic charger and it is functioning properly. We suggest that a manual charger NOT BE
USED with the QuadLink. Remember, the charger is always in control of the charge process, not the QuadLink.
9. Can I use this on my vehicle that has 4 batteries connected in parallel (in a 12V system)? YES, as long as
you are connecting only one station lead to this 12V pack. Although it will cause no harm, we do not suggest the
QuadLink be used in a parallel connected multi battery scenario as there is no additional charging benefi t when compared to single station charging to the pack.
10. Can I start my vehicle with the QuadLink still attached? YES, as long as your charger allows this capability. The
QuadLink does not control the charge going into the battery; it is only a conduit for the power going to each station.
11. Can I change the timing so that one battery charges longer before moving to the next battery? NO, the micro-
processor is not adjustable.
12. Can I connect two sets of leads to one battery so it will charge for an extended period? YES, if you want to
allow a certain battery to have more relative charge time within the charge cycle, you can “double connect” a
station to any given battery. This will give that battery 10 additional minutes of charge time per cycle.
For answers to additional questions, please see your dealer or contact PulseTech Products Corporation at
1-800-580-7554, 8 a.m. to 5 p.m. Monday through Friday CST or go to www.PulseTech.net.
PulseTech Products Corporation
What Does This Warranty Cover? This warranty covers any defects in workmanship or materials in the
product under normal use and service.
How Long Does The Coverage Last? This warranty runs for fi ve (5) years from the date of purchase.
What Will PulseTech Do? PulseTech will, at its option, repair the unit or replace the unit with a
remanufactured unit at no charge.
What Does This Warranty Not Cover? This warranty applies only to the product and does not cover
any other equipment, static damage, water damage, overvoltage, dropping of the unit or damage resulting from extraneous causes. The warranty is void if the owner attempts to disassemble the unit or modify
the cable assembly. In addition, PulseTech will not be responsible under this warranty if PulseTech determines that (1) upon examination that the unit’s failure was (A) caused by misuse, neglect, accident,
alteration, or abnormal condition of operating or handling (including the failure to install the product in
accordance with PulseTech’s instructions and observe the warnings on the product and the instruction
manual), or other conditions beyond the control of PulseTech or (B) damaged in transit to PulseTech,
or (2) the owner is not the original purchaser that purchased the product from PulseTech directly or
through an authorized PulseTech dealer or distributor. IN NO EVENT SHALL PULSETECH BE
LIABLE FOR ANY DIRECT, SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL, PUNITIVE OR EXEMPLARY DAMAGES, EXPENSES, LOST SAVINGS OR LOST PROFITS OR ANY
OTHER DAMAGES OF ANY KIND FROM ANY BREACH OF THIS WARRANTY OR OTHERWISE. Some states, provinces or countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you.
How To Get Service? Send the product postage prepaid with proof of purchase (sales receipt) within
the warranty period to the authorized reseller where the product was purchased or contact PulseTech
directly by calling 1-800-580-7554.
How Does State, Province or Country Law Apply? This warranty gives you specifi c legal rights, and
you may also have other rights which vary from state to state, province to province or country to country.
THIS WARRANTY IS THE SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL
OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE.
5-Year Limited Warranty
Southlake, TX 76092
Patent Pending
Model XC-QL4
PRODUCTS & ACCESSORIES
12V Xtreme Charger w/Pulse Maintenance
Ideally suited for AGM and Maintenance-Free
batteries. Increases the duty
and life cycle of all 12V
batteries up to fi ve
times longer.
Part #: 100X010
Model: XC-100-P
Quick Mount Wall Bracket
Part #: 100X808
Model: XC-QM
Full Enclosure Wall Bracket
Part #: 100X810
Model: XC-BKT
12V 2-Channel Charger w/Pulse Maintenance
Double the charging capabilities
of the popular XC-100-P
Xtreme Charge® 12V
Battery Charger. Each
station charges at a 2.5 A
(5 A effective) charge rate
at over 14.8V.
Part # 100X200
Model: X2
QuadLink™ 4-Channel Battery Charger Multiplier
Turns any 6/12V battery charger
(using the standard 2-prong
output connector) into a
4-station maintenance charger.
Part # 100X004
Model: XC-QL4
Battery Lead with Clips
This 7.5-amp fuse-protected cable is
supplied with a quick-disconnect
terminal. Lead is 2 feet long.
Part #: 100X827
Model: XC-CLIPS
“Leave-On” Battery Lead with Lugs
Xtreme Charge® 7.5-amp fuse-protected cable
comes with a quick-disconnect terminal.
Lead is 2 feet long.
Part #: 100X830
Model: XC-LUGS
5' and 25' Extension Lead
Extend a standard lead by 5 or 25 feet with these
extensions. They feature quick-disconnect
terminals on both ends. Lead is 5 feet
or 25 feet long.
Part #: 100X805
Model: XC-EXT-5
Part #: 100X825
Model: XC-EXT-25
Quick Battery Tester
Assess your 12V battery’s state of charge
quickly with this pocket-sized tester.
It will be the most used tester in shops,
garages and any areas where battery
checks are performed.
Part #: 100X822
Model: XC-822-TEST
TO PURCHASE ANY OF THESE ITEMS, VISIT WWW.PULSETECH.NET
998XM104 04/11
Loading...