Quad Q5-T, Q4-T, Q4, Q5 Owners Manual

REV.1

CONCOURSE Q SERIES

INSTRUCTION BOOKLET

MODELS Q4, Q4T, Q5, & Q5T

FOR THE CLOSEST APPROACH TO THE ORIGINAL SOUND

TABLE OF CONTENTS

Introduction:

Safety Instructions ....................................................................... 02

Introduction ................................................................................ 02

Warnings & Disclaimers .............................................................. 02

Rigging & Suspension ................................................................. 02

Warranty & Service .................................................................... 02

Product Descriptions:

Concourse Q4/Q4T.................................................................... 03

Concourse Q5/Q5T.................................................................... 03

Product Features:

Back Panel Drawing .................................................................... 03

Accessories ................................................................................ 04

Installation:

Installation Instructions ................................................................. 05

Connections:

Low Impedance Connections ........................................................ 07

70/100V Connections ................................................................ 07

Impedance Charts ...................................................................... 08

CE Compliance:

Statement ................................................................................... 08

Specifications ............................................................................. 09

Contact Information:

QUAD Industrial Contact Information ............................BACK COVER

SAFETY INSTRUCTIONS

Safety First!

1. Please read this manual fully before installing and operating this
product.

2. Retain a copy of this manual for future reference.

3. Comply with all warning labels and instructions.

4. Do not attempt the installation of this equipment unless you are
qualified to do so.

5. Protect your hearing from high sound pressure levels.

Rigging and Suspension

The rigging, suspension or mounting of these products can expose the
installer and members of the public to serious health risks and even death.

UNDER NO CIRCUMSTANCES ATTEMPT TO RIG, SUSPEND
OR OTHERWISE MOUNT THIS EQUIPMENT UNLESS YOU ARE
FULLY QUALIFIED AND CERTIFIED TO DO SO BY RELEVANT
LOCAL, STATE AND NATIONAL AUTHORITIES. ALL RELEVANT
SAFETY REGULATIONS MUST BE FOLLOWED. IF YOU ARE NOT
PROPERLY QUALIFIED OR DO NOT KNOW OF PERTINENT
REGULATIONS, CONSULT QUALIFIED PERSONNEL FOR ADVICE
AND ASSISTANCE.

Limited Liability

QUAD Industrial assumes no liability whatsoever for any damage or loss,
either direct or consequential arising from the installation and use of these
products. Liability is limited to replacement of product or refund, at the
QUAD Industrial’s discretion. Your rights to compensation may vary by ter
ritory; consult with your local QUAD Industrial office or distributor.

-

Warranty & Service

These products are designed to be used as specified, and are warranted to
be free from defects in materials or workmanship. Warranty terms and con
ditions vary by territory. Please contact your local QUAD Industrial sales
office or distributor for complete details. Under no circumstances should
you attempt to repair these products. Doing so may limit or void warranty
coverage.

2

-

PRODUCT DESCRIPTION

The Concourse Q4(T) and Q5(T) are two-way high performance
speaker systems designed for distributed music, paging and
speech applications. They combine quality transducers with
sophisticated crossover designs in lightweight and durable ABS
enclosures and come complete with mounting brackets and
hardware.

CONCOURSE Q4

The Concourse Q4 is a two-way speaker system consisting of a 4"
low frequency driver and a 1" dome tweeter and is supplied with
a wall mounting bracket. There are four versions available:

• Concourse Q4W – White, 8Ω, 25 Watts

PRODUCT FEATURES

The Q4/Q5 models are fitted with 4 threaded inserts on the rear
for attaching the supplied mounting bracket. There are also two
threaded inserts to accommodate after-market brackets.

Amplifier outputs are is connected to the speaker through a termi­nal strip mounted inside a recessed well on the rear of the speaker.

Mounting points for
supplied brackets

• Concourse Q4B –

• Concourse Q4TW – White, 15 Watt 70/100 Volt
transformer included

• Concourse Q4TB –

transformer included

Black, 8Ω, 25 Watts

Black, 15 Watt 70/100 Volt

CONCOURSE Q5

The Concourse Q5 is a two-way speaker system consisting of a 5"
low frequency driver and a 1" Dome tweeter and is supplied with
a wall mounting bracket. There are four versions available:

• Concourse Q5W –

• Concourse Q5B –

• Concourse Q5TW –

transformer included

• Concourse Q5TB –

transformer included

White, 8Ω, 35 Watts

Black, 8Ω, 35 Watts

White, 25 Watt 70/100 Volt

Black, 25 Watt 70/100 Volt

Mounting points for
other brackets

Input terminals

3

A complete installation kit designed to work with the supplied mounting brackets is included with each model and consists of:

1. Seismic restraint tethers (2)

2. Bracket mounting screws (8)

3. Lock washers (2)

4. Nylon locking nuts (2)

5. Friction pads (2)

6. Adhesively attached rubber feet (2)

1

2

5

3

4

6

Please ensure that you are familiar with all of the parts and how they are
assembled before starting the installation.

4

INSTALLATION

Step 1

Mount the bracket as shown to the wall or other mounting surface
using suitable screws.

Step 2

Mount the bracket with the threaded bolt to the cabinet using the
4 supplied screws.

Step 3

Place the rubber friction washer over the bolt.

Step 4

When you’re ready to install the speaker insert the bolt in the wall
bracket from below.

Step 5

Place the dome cover over the bolt.

Step 6

Place the lock washer and hex nut on the bolt. Tighten gently, aim
the speaker as needed and tighten firmly.

STEP 1

STEP 2

Step 7

Ensure that seismic restraint cable is firmly attached to both the
loudspeaker and an anchor point on the mounting surface.

STEP 3

5

STEP 4

STEP 7

STEP 5

STEP 6

FINISHED

6

LOW IMPEDANCE (8Ω) CONNECTIONS

Low impedance models are fitted with two terminals for the (+)
and (-) incoming amplifier feed and two terminals paralleled to the
next speaker.

Speakers may be wired in parallel as shown below. Ensure that
the total impedance of connected speakers does not fall below
the minimum impedance of the connected amplifier. The following
table shows the net impedance when several speakers are
combined in parallel.

Number of Speakers in Parallel Combined Impedance

70/100V CONNECTIONS

70/100V Models use one terminal for the Common (-) connection
and the other three terminals for the transformer power taps. Note
that the Q4T offers taps at 15W/7.5W/3.75W (below left) while
the Q5T offers taps at 25W/12.5W/6.25W (below right).

100V

Q4T

70V

100V

Q5T

70V

18Ω
24Ω
3 2.6Ω
42Ω

FROM

AMPLIFIER

TO NEXT
SPEAKER

COM

N/C

15W

7.5W

COM

15W

7.5W

3.75W

COM

N/C

25W

12.5W

COM

25W

12.5W

6.25W

NOTE:

Power taps are labeled for 70V operation. Connection of 100V
amplifiers requires use of the next lower wattage tap to prevent
damage to the speaker. See chart below.

7

V

M

.5W

W

V

M

/C

W

V

Model: Q4T Model: Q5T
Tap Label 70V 100V

Impedance

Ω

Tap Label 70V 100V

Impedance Ω

15W 15W N/C 320 25W 25W N/C 200

7.5W 7.5W 15W 640 12.5W 12.5W 25W 400

3.75W 3.75W 7.5W 1280 6.25W 6.25W 12.5W 800

Connect speakers in parallel as shown below:

00V

COM

N/C

7.5W

FROM

AMPLIFIER

0

COM

.75W

100

CO

N

15W

7.5

CO

7

3.75

TO NEXT
SPEAKER

Select the power tap by dividing the amplifier’s available power
by the number of speakers to be connected and then selecting the
next lower wattage tap. For example:

0

200W amplifier ÷ 20 speakers = 10 Watts; use the

7.5W terminal

Individual speakers may be tapped higher or lower in order to
better balance the system sound pressure level in different areas.
Ensure that the combined power draw does not exceed the
maximum rated power of the amplifier or damage to the amplifier
and speakers could occur.

CE COMPLIANCE

This product is in compliance with CE directives and bears the CE
mark. For detailed information on specific directives please contact
your local QUAD Industrial sales office or distributor.

8

SPECIFICATIONS

Power Handling: Q4 Q4T Q5 Q5T

Continuous 25W 70V: 3.75W/7.5W/15W 35W 70V: 6.25W/12.5W/25W
Program 50W 100V: 7.5W/15W 70W 100V: 12.5W/25W
Peak 100W 140W

Frequency Response: 60Hz−20kHz 60Hz−20kHz 50Hz−20kHz 50Hz−20kHz
(-10dB)

Frequency Response: 100Hz−20kHz 100Hz−16kHz 60Hz−20kHz 60Hz−16kHz
(+/-3dB)

Sensitivity (@2.83V): 84dB 83dB 85dB 84dB

Max SPL: 105dB 95dB 106dB 98dB

Coverage (H x V): 110˚ x 130˚ 110˚ x 130˚ 150˚ x 150˚ 150˚ x 150˚

Directivity (DI) (H x V): 6.62 6.62 5.36 5.36

Impedance: 8Ω N/A 8Ω N/A

Regulatory Approvals: CE CE CE CE
(9UL, CE)

Transducers:

LF Driver Size 4" Cone 4" Cone 5" Cone 5" Cone

HF Driver Size 1" Soft Dome 1" Soft Dome Tweeter 1" Soft Dome 1" Soft Dome

Crossover Frequency: 2.8kHz 2.8kHz 2.5kHz 2.5kHz

Enclosure Material: Plastic (ABS) Plastic (ABS) Plastic (ABS) Plastic (ABS)

Connector Type: Screw Terminal Screw Terminal Screw Terminal Screw Terminal

Dimensions: 9.1" x 6.3" x 5.8" 9.1" x 6.3" x 5.8" 7.3" x 7.3" x 11" 7.3" x 7.3" x 11"
(H x W x D) 232 x 160 x 148mm 232 x 160 x 148mm 185 x 185 x 280mm 185 x 185 x 280mm

Net Weight: 4.6lbs. 5.28lbs. 5.5lbs. 5.5lbs.

2.1kg 2.4kg 2.5kg 2.5kg

* Features, details & specifications are subject to change without notice

9

USA CONTACT:

ph +877.440.0888
ph +425.861.3909
fx +425.861.3906

UK CONTACT:

ph +0845 4580011
ph [phone]
fx [phone]

OUTSIDE USA & UK:

ph [phone]

fx [phone]

REV.1

WEB:

www.quadindustrial.com

FOR THE CLOSEST APPROACH TO THE ORIGINAL SOUND

© 2006 QUAD Industrial. QUAD Industrial is a member of the International Audio Group. IAG America Inc. 8440 154th Avenue NE · Redmond, WA 98052