QUAD FORUM - REV 1, FORUM 8, FORUM 10, FORUM 12, FORUM 15 Instruction Booklet

...
F O R U M S E R I E S
INSTRUCTION BOOKLET
MODELS FORUM 8, 10, 12, 15, 8M, 15M & FORUM 12SUB & 15SUB
F O R T H E C L O S E S T A P P R O A C H T O T H E O R I G I N A L S O U N D
R E V.1
2
SAF ETY INST RU CTIO NS
1. Please read this manual fully before installing and operating this product.
2. Retain a copy of this manual for future reference.
3. Comply with all warning labels and instructions.
4. Do not attempt the installation of this equipment unless you are qualified to do so.
5. Protect your hearing from high sound pressure levels.
Rigging and Suspension
The rigging, suspension or mounting of these products can expose the installer and members of the public to serious health risks and even death.
UNDER NO CIRCUMSTANCES ATTEMPT TO RIG, SUSPEND OR OTHERWISE MOUNT THIS EQUIPMENT UNLESS YOU ARE FULLY QUALIFIED AND CERTIFIED TO DO SO BY RELEVANT LOCAL, STATE AND NATIONAL AUTHORITIES. ALL RELEVANT SAFET Y REGULATIONS MUST BE FOLLOWED. IF YOU ARE NOT PROPERLY QUALIFIED OR DO NOT KNOW OF PERTINENT REGULATIONS, CONSULT QUALIFIED PERSONNEL FOR ADVICE AND ASSISTANCE.
Limited Liability
QUAD Industrial assumes no liability whatsoever for any damage or loss, either direct or consequential arising from the installation and use of these products. Liability is limited to replacement of product or refund, at QUAD Industrial’s discretion. Your rights to compensation may vary by territory; consult with your local QUAD Industrial office or distributor.
Warranty & Service
These products are designed to be used as specified, and are warranted to be free from defects in materials or workmanship. Warranty terms and con
­ditions vary by territory. Please contact your local QUAD Industrial sales office or distributor for complete details. Under no circumstances should you attempt to repair these products. Doing so may limit or void warranty coverage.
TA BL E OF CON TENT S
Introduction:
Safety Instructions ....................................................................... 02
Introduction ................................................................................ 02
Warnings & Disclaimers .............................................................. 02
Rigging & Suspension ................................................................. 02
Warranty & Service .................................................................... 02
Product Features:
Product Descriptions .................................................................... 03
Dimension Drawings................................................................... 05
Installation:
Wall or Pole Mounting ................................................................ 07
3-Point Hanging ......................................................................... 07
Speaker Stand Adapter ............................................................... 07
Wiring & Connections:
Connections & Operations ........................................................... 08
CE Compliance:
Statement ................................................................................... 08
Specifications ............................................................................. 09
Contact Information:
QUAD Industrial Contact Information ............................BACK COVER
3
PRO DUCT DES CR IPTI ON
The Forum range of two-way loudspeakers and complementary subwoofers are high-performance point-source systems designed for the most demanding voice and music reinforcement applica­tions. Each full range model is built around a genuine QUAD Industrial DuAlign™ precision transducer, offering linear response in both amplitude and phase domains. Complemented by trap­ezoidal enclosures and supplied mounting hardware, all Forum models are ready for installation in a variety of applications.
FOR UM 8
The Forum 8 is a compact two-way speaker system consisting of an 8" DuAlign™ woofer with integral 2" compression driver. The speaker comes with a yoke mounting bracket and a three-point hang accessory. There are two versions available:
• Forum 8 –
Black, 8Ω, 100 Watts
• Forum 8W –
White, 8Ω, 100 Watts
FOR UM 8 M
The Forum 8M is a compact two-way floor monitor system consisting of an 8" DuAlign™ woofer with integral 2" compres­sion driver. Its low profile and clean functional design allow it to complement any interior space. There are two versions available:
• Forum 8M –
Black, 8Ω, 100 Watts
• Forum 8MW –
White, 8Ω, 100 Watts
FOR UM 1 0
The Forum 10 is a compact two-way speaker system consisting of a 10" DuAlign™ woofer with integral 2" compression driver. The speaker comes with a yoke mounting bracket and a three-point hang accessory. There are two versions available:
• Forum 10 –
Black, 8Ω, 150 Watts
• Forum 10W –
White, 8Ω, 150 Watts
FOR UM 1 2
The Forum 12 is a compact two-way speaker system consisting of a 12" DuAlign™ woofer with integral 2" compression driver. The speaker comes with a yoke mounting bracket and a three-point hang accessory. There are two versions available:
• Forum 12 –
Black, 8Ω, 200 Watts
• Forum 12W –
White, 8Ω, 200 Watts
FOR UM 1 5
The Forum 15 is a compact two-way speaker system consisting of a 15" DuAlign™ woofer with integral 2" compression driver. The speaker comes with a yoke mounting bracket and a three-point hang accessory. There are two versions available:
• Forum 15 –
Black, 8Ω, 300 Watts
• Forum 15W –
White, 8Ω, 300 Watts
FOR UM 1 5M
The Forum 15M is a compact two-way floor monitor system consisting of a 15" DuAlign™ woofer with integral 2" compres­sion driver. Its low profile and clean functional design allow it to complement any interior space. There are two versions available:
• Forum 15M –
Black, 8Ω, 300 Watts
• Forum 15MW –
White, 8Ω, 300 Watts
4
FOR UM 1 2SUB
The Forum 12SUB is a folded horn low-profile sub-bass speaker comprised of a single 12" long throw driver. Its compact dimen­sions make it ideal for concealed installation or where space is limited. The Forum 12SUB is available in two versions:
• Forum 12SUB-4 –
Black, 4Ω, 300 Watts
• Forum 12SUB-4W –
White, 4Ω, 300 Watts
FOR UM 1 5SUB
The Forum 15SUB is a folded horn low-profile sub-bass speaker comprised of a single 15" long throw driver. Its compact dimen­sions make it ideal for concealed installation or where space is limited. The Forum 15SUB is available in two versions:
• Forum 15SUB-4 –
Black, 4Ω, 450Watts
• Forum 15SUB-4W –
White, 4Ω, 450Watts
PRO DUCT FEATUR ES
All Forum series models except for the Forum 8M and Forum 15M are fitted with a unique yoke mounting bracket that facili­tates mounting and suspension of the loudspeaker. In addition, these models are supplied with hardware that permits rigging and suspension from three points, allowing the cabinet to be angled as needed. A pole adapter is provided for use with tripod speaker stands.
All models are fitted with NL4 socket connections. In addition, all models except for the Forum 8M and Forum 15M are fitted with heavy duty barrier strips for direct termination of amplifier wiring. Cabinets are constructed of high-density MDF and finished in durable paint with matching steel grilles.
NOTE: Please ensure that you are familiar with all of the mount­ing hardware and possess the required experience and related certification before installing these products.
5
DIM ENSI ONS
Forum 12
Forum 8
322mm/12.7”
285mm/11.2”
430mm/17”
Forum 10
322mm/12.7”
508mm/20”
375mm/14.8”
Forum 15
558mm/22”
449mm/17.7”
Forum 8M
Depth: 410mm/16.1”
Width: 285mm/11.2”
322mm/12.7”
Forum 15M
Depth: 440mm/17.3”
Width: 449mm/17.7”
Height: 220mm/8.7”
Height: 350mm/13.8”
6
INS TALL ATI ON
Carefully unpack the contents of the shipping carton and verify that all of the mounting hardware is accounted for. The supplied hardware will support three types of installation as detailed below:
Wall or Pole Mounting
This method allows mounting of the loudspeaker to any suitable vertical surface such as a wall or pole.
Step 1
Remove the mounting yoke from the loudspeaker by removing the bolts on the top and bottom of the enclosure.
Step 2
Mount the bracket to the mounting surface using suitable fasteners through the pre-drilled holes in the bracket’s spine.
Step 3
Place the loudspeaker into the yoke bracket and re-insert the mounting bolts, taking care to make them snug, without over tight­ening. Use of thread locking compound is recommended.
3-P OINT HAN GI NG
This method allows the suspension of the loudspeaker from a truss or building structure using stranded safety cable or suitably rated chain securely attached to three points on the cabinet using the supplied brackets and hardware.
Step 1
Remove the bolt holding the mounting yoke to the top of the cabi­net and install the suspension adapter as shown. Tighten the bolt taking care not to over tighten. Use of thread locking compound is recommended.
DIM ENSI ONS
Forum 12SUB
195mm/7.7”
750mm/29.5”
850mm/33.5”
Forum 15SUB
220mm/8.7”
Forum 15XB Forum 18XB
440mm/17.33”
610mm/24”
610mm/24”
522mm/20.6”
7
Step 2
Install the rear suspension point bracket to the back side of the yoke using the supplied nut and bolt. Note that the bracket can be installed in a variety of positions along the vertical axis of the yoke. This permits the cabinet to be tilted as needed for precise aiming.
SPE AKER STA ND A DAPT ER
A third mounting option permits the speaker to be installed onto a standard tripod speaker stand or third-party mounting bracket using the supplied stand adapter.
Step 1
Remove the mounting yoke from the loudspeaker by removing the bolts on the top and bottom of the enclosure.
Step 2
Insert the stand adapter into the bottom of the enclosure and secure with the bolt removed in step 1. Re-insert the bolt removed from the top of the enclosure.
Step 3
Place the loudspeaker onto the stand and tighten the positioning screw using the plastic handle. Hand tighten only.
CON NECT ION & OPER ATI ON
All models are fitted with NL4 style power input sockets for con­nection to power amplifiers. NL4 connections are recommended for all applications, whether permanent installation or portable application. In addition all models except for the Forum 8M and Forum 15M are fitted with barrier strips for direct termination of wiring. On models equipped with both NL4 and barrier strip connectors all connections are paralleled between the two connector types.
Multiple speakers may be wired in parallel providing that the resulting impedance is not below the minimum rated operating impedance of the power amplifier. Refer to the amplifier installa­tion manual for further details. Note that all Forum speaker models are supplied in 8Ω configuration, except for the Forum 12Sub and Forum 15Sub, which are also available in 4Ω versions.
The following table shows the net impedance when several 8Ω speakers are combined in parallel.
# of 8 Ω Speakers in Parallel
Combined Impedance
2
4 Ω
3
2.6 Ω
4
2 Ω
NOTE: Never connect more than two 4Ω speakers in parallel on one amplifier channel.
Always ensure that sound sources are set at the minimum level before powering up the amplifier or powered speakers, for the first time. Apply signal and increase the level slowly, verifying that the signal is reaching the speakers and that the sound is clear and free of distortion.
COM PLIA NCE
This product is in compliance with CE directives and bears the CE mark. For detailed information on specific directives please contact your local QUAD Industrial sales office or distributor.
* Features, details & specifications are subject to change without notice
8
FOR UM S PEAK ER SPE CIFI CAT IO NS
Power Handling: FORUM 8 FORUM 10 FORUM 12 FORUM 15
Continuous 100W 150W 200W 300W Program 200W 300W 400W 600W Peak 400W 600W 800W 1200W
Frequency Response: 60Hz−20kHz 55Hz−20kHz 60Hz−20kHz 60Hz−20kHz (-10dB)
Frequency Response: 90Hz−20kHz 90Hz−20kHz 90Hz−20kHz 70Hz−20kHz (+/-3dB)
Sensitivity (@2.83V): 90dB/1watt/1meter 92dB/1watt/1meter 94dB/1watt/1meter 95dB/1watt/1meter
Max SPL: 116dB 120dB 123dB 126dB
Coverage (H x V): 70˚ Conical 55˚ Conical 60˚ Conical 65˚ Conical
Directivity: 6.69 7.15 7.21 7.1
Impedance: 8Ω nominal 8Ω nominal 8Ω nominal 8Ω nominal
Regulatory Approvals: CE CE CE CE (9UL, CE)
Transducers:
LF Driver Size 8" Coaxial 10" Coaxial 12" Coaxial 15" Coaxial
HF Driver Size 2" Compression Driver 2" Compression Driver 2" Compression Driver 2" Compression Driver
Crossover Frequency: 2.3kHz 2.2kHz 2.0kHz 2.1kHz
Enclosure Material: MDF MDF MDF MDF
Connector Type: Speakon™/Terminal strip Speakon™/Terminal strip Speakon™/Terminal strip Speakon™/Terminal strip
Dimensions: 370 x 285 x 280mm 430 x 322 x 320mm 508 x 375 x 350mm 558 x 449 x 430mm (H x W x D) 14.6" x 11.2" x 11" 17" x 12.7" x 12.6" 20" x 14.8" x 13.8" 22" x 17.7" x 17"
Net Weight: 11.2kg 15kg 17.6kg 23.5kg
24.6lbs. 33lbs. 38.7lbs. 52lbs.
* Features, details & specifications are subject to change without notice
9
FOR UM S PECI FI CAT IONS
Power Handling: FORUM 8M FORUM 15M FORUM 12SUB FORUM 15SUB
Continuous 100W 450W 300W 450W Program 200W 900W 600W 900W Peak 400W 1800W 1200W 1800W
Frequency Response: 70Hz−20kHz 70Hz−20kHz 40Hz−300Hz 35Hz−350Hz (-10dB)
Frequency Response: 95Hz−20kHz 95Hz−20kHz 45Hz−200Hz 40Hz−200Hz (+/-3dB)
Sensitivity (@2.83V): 92dB/1watt/1meter 96dB/1watt/1meter 98dB/1W/1 meter 99dB/1W/1 meter
Max SPL: 118dB 128dB 128dB 131dB
Coverage (H x V): 50˚ Conical 60˚ Conical N/A N/A
Directivity: 6.97 7.55 N/A N/A
Impedance: 8Ω nominal 8Ω nominal 4Ω nominal 4Ω nominal
Regulatory Approvals: CE CE CE CE (9UL, CE)
Transducers:
LF Driver Size 8" Coaxial 15" Coaxial 12" Long Throw 15" Long Throw
HF Driver Size 2" Compression Driver 2" Compression Driver N/A N/A
Crossover Frequency: 2.3kHz 2.1kHz 250Hz LPF 250Hz LPF
Enclosure Material: MDF MDF MDF MDF
Connector Type: Speakon™ Speakon™ Speakon™/Terminal strip Speakon™/Terminal strip
Dimensions: 370 x 285 x 287mm 558mm x 449mm x 387mm 240mm x 750mm x 595mm 266mm x 850mm x 670mm (H x W x D) 14.6" x 11.2" x 11.3" 22" x 17.7" x 15.2" 9.4" x 29.5" x 23.4" 10.5" x 33.5" x 26.4"
Net Weight: 9.8kg 21kg 38.5kg 47.1kg
21.6lbs. 46.2lbs. 85lbs. 104lbs.
R E V.1
F O R T H E C L O S E S T A P P R O A C H T O T H E O R I G I N A L S O U N D
© 20 06 QUA D Ind us tri al . Q UA D I ndu st ria l is a mem ber o f t he In te rna ti ona l A ud io Gr oup . IAG Am er ica I nc. 8 440 1 54t h A ve nue NE · Re dm ond , WA 980 52
U S A C O N T A C T :
p h + 1 . 8 7 7 . 4 4 0 . 0 8 8 8 p h + 1 . 4 2 5 . 8 6 1 . 3 9 0 9 f x + 1 . 4 2 5 . 8 6 1 . 3 9 0 6
U K C O N T A C T :
p h + 4 4 ( 0 ) 8 4 5 4 5 8 0 0 1 1 p h + 4 4 ( 0 ) 1 4 8 0 4 4 7 7 0 0 f x + 4 4 ( 0 ) 1 4 8 0 4 3 1 7 6 7
O U T S I D E U S A & U K :
p h + 8 6 ( 0 ) 7 5 5 8 2 0 9 6 6 3 9
f x + 8 6 ( 0 ) 7 5 5 8 2 0 9 0 2 0 3
W E B :
w w w . q u a d i n d u s t r i a l . c o m
Loading...