Page 1
1675 MacArthur Boulevard • Costa Mesa, CA 92626
Ph: 800/854-4079 or 714/957-7100 • Fax: 714/754-6174
© 2020 QSC, LLC all rights reserved. QSC and the QSC logo are registered trademarks of QSC, LLC in the U.S. Patent and Trademark office and other
countries. All other trademarks are the property of their respective owners. Patents may apply or be pending.
www.qsc.com
614-00030
unDNEMO
User Manual
Date 2/21/2020
Dante™/AES67 Network Audio Interface
Page 2
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
IMPORTANT SAFETY INSTRUCTIONS
The symbols below are internationally accepted symbols that warn of potential hazards with electrical products.
This symbol, wherever it appears, alerts you to the presence of un -insulated dangerous voltage inside the
enclosure -- voltage that may be sufficient to constitute a risk of shock.
This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the
accompanying literature. Please read the manual.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and third grounding prong. The wider blade or
the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician
for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by Attero Tech
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
13. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
14. Unplug this apparatus during lightning storms or when unused for long periods of time.
15. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in
any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
16. This apparatus shall be connected to a mains socket outlet with a protective earthing connection.
17. When permanently connected, on all-pole mains switch with a contact separation of at least 3mm in each pole
shall be incorporated in the electrical installation of the building.
18. If rack mounting, provide adequate ventilation. Equipment may be located above or below this apparatus but
some equipment (like large power amplifiers) may cause an unacceptable amount of hum of may generate too
much heat and degrade the performance of this apparatus,
19. This apparatus may be installed in a industry standard equipment rack. Use screws through all mounting holes
to provide the best support.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
Page 3
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
WARRANTY INFORMATION
For a copy of the QSC Limited Warranty, visit the QSC website at www.qsc.com
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules and EN55022. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference,
in which case the user will be required to correct the interference at their own expense.
This symbol means the product must not be discarded as household waste, and should be delivered to an
appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources,
human health and the environment. For more information on disposal and recycling of this product, contact
your local municipality, disposal service, or the business where you bought this product.
Page 4
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
Contents
1 – Overview..................................................................................................................................................................................................................... 5
1.1 – What’s in the Box? ..................................................................................................................................................................... 5
1.2 – Optional Extras .......................................................................................................................................................................... 5
1.3 – Product Features ....................................................................................................................................................................... 6
2 – User Operation ........................................................................................................................................................................................................ 8
2.1 – User Interface Description ....................................................................................................................................................... 8
2.1.1 – Display Layout ................................................................................................................................................................. 8
2.1.2 – Keypad Layout ................................................................................................................................................................. 8
2.2 – Audio Mode Navigation ............................................................................................................................................................ 9
2.2.1 – Net Mode .......................................................................................................................................................................... 9
2.2.2 – USB Mode .......................................................................................................................................................................... 9
2.2.3 – Line Input Mode ............................................................................................................................................................ 10
2.2.4 – All Input Mode ............................................................................................................................................................... 10
2.3 – Menu Mode Navigation .......................................................................................................................................................... 11
2.3.1 – Menu Mode: Brightness Control ................................................................................................................................. 12
2.3.2 – Menu Mode: Device Info ............................................................................................................................................... 12
3 – System Setup ......................................................................................................................................................................................................... 13
3.1 – Single Port Mode ..................................................................................................................................................................... 13
3.2 - Daisy Chain Deployment ........................................................................................................................................................ 13
3.3 – PoE Deployment ...................................................................................................................................................................... 15
3.4 – Dante Configuration Notes.................................................................................................................................................... 16
3.5 – Factory Reset ............................................................................................................................................................................ 16
4 – Mechanical Information ................................................................................................................................................................................... 17
4.1 – Mounting Information ............................................................................................................................................................ 17
5 – ARCHITECTS & ENGINEERS SPECIFICATION ........................................................................................................................................... 18
5.1 – Device Specifications .............................................................................................................................................................. 19
APPENDIX A – Reference Documents ...............................................................................................................................................................A-1
Page 5
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
1 – Overview
The unDNEMO is a highly flexible DanteTM network audio monitoring solution that can be deployed in a wide array of proAV applications. The unDNEMO is capable of monitoring one audio channel selected from up to 64 configured DanteTM
network audio channels that are available on the network from Dante enabled audio equipment from any manufacturer.
Audio selection is done with simple front panel controls. The unDNEMO utilizes Attero Tech’s unIFY Control Panel v2.0
or later software for simple setup and configuration.
In addition to the flexible Dante® audio monitoring functionality, the unDNEMO is aimed at comprehensive audio
monitoring applications and supports the following features:
o User selectable reception of one of up to 64 Dante
TM
audio channels
o Internal monitoring speaker
o Internal microphone with optional external mic input, allowing for talkback communications or for s oft-
conferencing applications in conjunction with the USB audio interface
o Easy access front panel headset (headphone and mic connections) on 3.5mm connectors
o Volume, channel, mic mute, speaker mute, and source select buttons
o Easy-to-read OLED display for presentation of channel names, volume settings and configuration
o Full duplex USB audio for PC audio content and soft-conferencing applications
o PoE powered to work with any external +24VDC supply or compliant 802.3af PoE network switch or mid-
span injector
o Dante Daisy Chaining allows multiple unDNEMO devices, as well as other Attero Tech daisy chain enabled
devices, to be connected over a single home-run to an Ethernet switch
1.1 – What’s in the Box?
The unDNEMO comes supplied with the following
o (1) unDNEMO device
o (1) USB Mini B to USB A 6ft cable
1.2 – Optional Extras
The following are available as options for the unDNEMO and that may be ordered separately:
o 24V DC Power Supply - P/N: 900-00175
Page 6
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
1.3 – Product Features
Figure 1 - unDNEMO Top Panel Features
1
Internal speaker
2
OLED Display
3
Backlit Keypad with Mute state indication
4
3.5mm T-S Headset Mic (Left) and 3.5mm Stereo Headphone TRS (Right)
5
Internal microphone
Page 7
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
Figure 2 - unDNEMO Rear Panel Features
6
3.5m TRS Stereo Line Input
7
2x2 USB Audio interface on USB-mini B
8
Recessed Factory Reset switch
9
Daisy Chain Dante Ethernet ports (Left port supports 802.3af PoE)
10
24V DC Power Input
*Note: The unDNEMO has a label on the base of the unit that shows the devices MAC address. This is important for initial
device identification as the last six digits make up part of the devices default network name that is shown when the device
is detected by Dante Controller.
Page 8
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
2 – User Operation
The unDNEMO features a number of different modes and capabilities. The unDNEMO supports the following audio modes:
Net Mode
USB Mode
Line Input Mode
All Input Mode
All of these audio modes except the Net Mode can be enabled or disabled for the intended application using the unIFY
Control Panel Software. For detailed software configuration instructions, consult with the integrated Help documentation
included with the software.
2.1 – User Interface Description
2.1.1 – Display Layout
The unDNEMO features a high visibility OLED display for high visibility in varying ambient light conditions. The display
screens are organized into a title bar, main active content area and a status bar. The status bar always indicates the active
audio source mode and the current volume settings.
2.1.2 – Keypad Layout
The keypad controls consist of the following buttons:
Output Mute
Menu
Mic Mute
Channel/Nav Down
Channel/Nav Up
Source Select
Volume Down
Volume Up
The mute buttons always function to mute their
respective audio functions. Additionally, the “Menu”
button is always used to toggle between Menu and
Audio modes.
The remaining buttons are multi-function based on the
active mode and will be further explained in the detailed
descriptions of each audio and menu mode .
The unDNEMO features a configurable inactivity
timeout, when this timeout expires the display will go
dark, but the keypad will remain at the programmed
brightness setting.
Figure 4 – Keypad Layout
Figure 3 - Display Layout
Page 9
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
2.2 – Audio Mode Navigation
The user may cycle through the available audio modes by pressing the “Select” button to toggle through the available
modes.
Figure 5 - Audio Mode Screen Flow
The audio modes will accessed based on the order shown in Figure 5. If any of the configurable modes are disabled from
the configuration software, then those modes will simply be skipped over to the next available mode.
In the audio modes, the Volume +/- buttons are always used to adjust the speaker and headphone volume. The volume
range is 1 to 10. Additionally, the speaker Mute button will always operate as an audio mute function for the attached
headphone and speaker. The mute buttons indicate mute state by lighting their associated red LED when mute is.
When headphones are plugged into the unDNEMO, the internal speaker is automatically disabled until the headphones
are removed.
*Note: By default, only the Net Mode is enabled, pressing the “Select” button when only Net mode is enabled will result in
the message “Unsupported Function” to be shown briefly on the display.
2.2.1 – Net Mode
The primary operating mode for audio monitoring is the Net Mode. In this
mode Dante audio channels may be selected by the user from the front
panel controls for simple and efficient audio monitoring applications.
When in this mode the display will indicate the channel number that has
been assigned using the unIFY Control Panel Software in the top area of
the display and the configured channel name for t he selected channel in
the central viewing area of the displayed.
Only channels that are assigned and enabled within the unIFY Control Panel software will be shown on the display as the
channel Up/Down buttons are used to cycle through the channel list.
The device supports up to 64 channels that can be configured for monitoring. If a configured Dante channel is selected
but no longer available on the audio network, the screen will toggle between the channel name and the warning message
“Channel Unavailable”. Otherwise, if t he channel is available a subscription will be made as quickly as possible to the
Dante audio channel and then audio will be heard through the internal speaker or connected headphones.
When an audio subscription is made, the selected channel will be mapped to both the left and r ight headphone outputs
providing and a mono signal will be routed to the internal speaker.
By default, the unDNEMO is configured with a sample list o f device names and channel names and must be configured
prior to first use.
If Dante TX audio features are enabled within the unIFY Control Panel software for the unDNEMO, the microphone audio
will be routed to the first Dante audio channel. Dante Controller or another 3rd party application must be used to route
the audio to the intended Dante receive device.
2.2.2 – USB Mode
The USB mode of the device allows the user to use the unDNEMO as a USB
soundcard for a connected Mac or PC computer.
In this mode, the playback audio from the PC is routed to the internal
speaker or headphones if connected. The microphone audio is routed to
the USB audio record output to the connected PC. The audio playback
features stereo audio capabilities when used in USB mode.
Figure 6 – Brightness Control
Figure 7 – Brightness Control
Page 10
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
When this mode is selected, the device will detect the USB connection and show “Connected to Host” on the display if
connected, and show “No Host Present” if no USB connection is present.
If Dante TX audio features are enabled within the unIFY Control Panel software for the unDNEMO, the USB playback audio
will be routed to the first and second Dante audio transmit channels o f the device for stereo playback. Dante Controller
or another 3rd party application must be used to route the audio to the intended Dante receive device.
*NOTE: The PC/Mac soundcard volume control will override the internal unDNEMO volume control. Prior to disconnecting
the USB connection, it is recommended that the volume be set to the maxim um setting, such that the internal device
volume is not limited by the soundcard volume when the soundcard is not in use. Power cycling the unit will reset the
internal volume back to the soundcard volume defaults.
2.2.3 – Line Input Mode
The line input mode allows the user to connect a line-level analog audio
device to the rear panel 3.5mm TRS stereo analog input as a n auxiliary
audio source.
Audio is routed from the line input as a mono mix to the internal speaker
or as a stereo source to connected headphones.
If Dante TX audio features are enabled within the unIFY Control Panel
software for the unDNEMO, the line input audio will also be routed to the first and second Dante audio transmit channels
of the device for audio bridging applications. Dante Controller or another 3rd party application must be used to route the
audio to the intended Dante receive device.
2.2.4 – All Input Mode
The all input mode allows the user to simultaneously monitor a mix of the
audio from the selected Dante network audio channel, the line level
analog input and the USB audio input. This is useful in applications that
require monitoring audio from multiple, independent sources
simultaneously.
Figure 10 - All Input Mode Audio Routing
In the All input mode, the USB, and Line input sources are indicated with a checkmark on the title bar of the display when
they are connected.
The main content area of the screen shows the channel name of the network input audio, with the active channel number
shown in the center of the title bar.
The channel Up/Down buttons are used to navigate the network audio channel selection just as they operate in the Net
Mode.
The All Input mode does not support any Dante TX audio routing capabilities.
Figure 8 – Brightness Control
Figure 9 – Brightness Control
Page 11
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
2.3 – Menu Mode Navigation
The unDNEMO features a number of menu screens for showing status and basic device configuration. The menu mode
access is also a configurable option that can be disabled for applications where the end user may only require limited
access to the devices features. By default, the menu mode access is disabled and must first be enabled from the
configuration software. Once enabled, the menu mode may be entered by pressing the “Menu” button. While in menu
mode, the display will indicate MENU: in the upper left of the screen. To exit menu mode, press the MENU button again
to toggle back to the audio modes.
The following diagram depicts the menu navigation. Use the Up and Down channel buttons to cycle between the Display
Brightness and Device Info menus.
Use the “+” and “-“ buttons to adjust the value or navigate the sub-menus for each menu mode screen.
Figure 11 - Menu Mode Screen Navigation
Page 12
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
2.3.1 – Menu Mode: Brightness Control
The brightness control menu allows the user to adjust the brightness
level of the display and the keypad LED backlight brightness by
adjusting the level with the “+” and “-“ buttons respectively.
2.3.2 – Menu Mode: Device Info
The device info menus allow the user to view information about the
device including the Dante device name that is advertised on the Dante
network, the FW version information, the device MAC address and the
current device IP address.
To navigate between the Device Info menu screen content, use the “+”
and “-“ buttons respectively.
The FW versions screen shows the version information for both the
device application processor (shown as FW:) and the Dante product
version (shown as D:).
The MAC address screen shows the device MAC address and can also
be identified by referencing the label placed on the bottom of the unit.
The IP address screen shows the current IP address of the device. To
change the IP address settings, use Dante Controller or other
configuration software that supports general networking configuration
for Dante devices.
Figure 12 – Brightness Control
Figure 13 - Device Info: Name
Figure 14 - Device Info: FW Versions
Figure 15 - Device Info: MAC
Figure 16 - Device Info: IP
Page 13
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
3 – System Setup
*Note: All Attero Tech products are tested using UTP cabling and it is recommended that UTP cabling be used when
installing them. STP cabling can be used for installation though care must be taken not introduce grounding issues into
the system by doing so.
3.1 – Single Port Mode
The unDNEMO is configured for single port mode by default. In this mode the second, non -PoE powered Ethernet port is
disabled to provide security for applications that require restricted access to the network.
For a device that has been altered from its factory defaults, single port mode may be re-enabled via Dante Controller.
Select “Single Port” from the Network Config tab within the Device View window. This will require a reboot of the device.
3.2 - Daisy Chain Deployment
The unDNEMO can be deployed in standard Ethernet networks with and without external switching hardware. To enable
this switched mode, select “Dual Port – Switched” from the Network Config tab within the Device View window. This will
require a reboot of the device.
The first example below shows the Dante port of an audio DSP connected to the Ethernet (Dante) port of the unDNEMO
at supervisor station 1. Due to the integrated Gigabit Ethernet switch, other unDNEMO devices can be daisy-chained
together to eliminate the need for any external Ethernet switches.
*Note: Each unDNEMO would require a local 24V DC power supply connection. Daisy chain of PoE is not possible.
Figure 17 – Daisy Chain Deployment
*NOTE: It is not recommended to connect high channel co unt Dante devices to the end of any daisy -chain segment. The
daisy chain feature is intended to ease deployment in situations where additional Ethernet switches may be obtrusive and
Page 14
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
difficult to install. The daisy-chain feature is not intended to be use as a high bandwidth connection between two or more
Ethernet switches to bridge network segments.
Page 15
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
3.3 – PoE Deployment
The unDNEMO supports PoE 802.3af power on the left -most Ethernet port labeled “PoE+Data” on the rear panel of the
unit. To utilize PoE, connect CAT-5e or better cabling between the PoE port of the unDNEMO and an 802.3af compliant
PoE Ethernet switch or midspan power injector.
In this configuration, PoE cannot be daisy-chained and each device requires a CAT-5 connection back to the Ethernet
switch. The following diagram shows the unDNEMO devices used with an Ethernet switch providing both PoE and Dante
connections, with audio sourced from an Attero Tech unD4I 4 -channel analog input to Dante interface.
Figure 18 – PoE Deployment
Page 16
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
3.4 – Dante Configuration Notes
In general, there is little to no additional configuration required to successfully utilize the unDNEMO devices in a Dante
network other than the initial channel configuration and setup required using the unIFY Control Panel software.
However, if the unDNEMO is utilized in a Dante network with audio transmit channels that are already configured to
transmit to one or more Dante receive devices, the potential exists that the unDNEMO will not be able to subscribe to the
Dante transmitter as the number of unicast receivers assigned to transmitting device and channel may be exceeded.
To mitigate this issue, the desired audio channels may be placed in multicast flows such that there is no limit on the
number of Dante receive devices. In systems where a large number of unDNEMO devices are utilized, this is the
recommended practice to mitigate these channel subscription limitations that exist when only using unicast Dante audio
transmission. Care should always be taken to understand how much multicast bandwidth exists on the Dante network,
and utilize the tools within Dante Controller to identify any networking and Dante configuration issues.
3.5– Factory Reset
The unDNEMO and unDNEMO-BT have a factory reset option. Using it will reset all the devices parameters back to their
factory defaults including all the Dante® settings such as device name, channel names as well as the device settings such
as input select. The devices IP address mode is also reset back to getting a dynamic IP.
Access to the factory reset button is through a small circular hole on the rear of the unit between the USB and PoE Ethernet
connector.
To use the factory reset, insert a small screwdriver or paperclip into the hole to activate the factory reset switch. There
should be a noticeable “click” when it’s activated. Hold the switch in for appro ximately 10 seconds then release. If the
factory reset was successful, a few seconds after releasing the switch, the unit will reset itself.
Page 17
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
4– Mechanical Information
4.1 – Mounting Information
The unDNEMO is designed to be placed on a smooth surface and features a non-slip pad on the base of the unit.
For mounting on non-horizontal surfaces, the base of the unit features two keyhole openings for mounting that accept a
#6 size screw head. Care should be taken not to insert the screw head deeper than 6.00mm from the base of the unit.
Figure 22 - Front View Dimensions
Figure 21 – Side View Dimensions
Figure 19 - Top View Dimensions
Figure 20 - Bottom View Dimensions
Page 18
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
5 – ARCHITECTS & ENGINEERS SPECIFICATION
The Dante network monitor shall be able to monitor any one of up to 64 Dante audio flows, and provide user selection
of both channel and volume. The unit shall include a speaker and a headphone jack for reproduction of the Dante audio.
The unit shall provide bi-directional USB 1.1 audio connectivity, and install without additional drivers on both Windows
and Mac PCs. The unit shall provide one mic level and one line -level analog input, each on a 3.5mm connector. The unit
shall be able to receive power from either the rear panel Dante interface over the Ethernet cable from a compliant 802.3af
PoE network device or an external +24VDC power supply. A second rear panel Dante interface shall provide for daisy
chain of the Dante network.
The Dante interface shall be compliant with the RoHS, REACH and WEEE directives.
The Dante interface unit shall be compliant with the EMI/EMC requirements for FCC (Part 15 Class A) and CE (EN 55022
Class) A.
The Dante interface shall be the Attero Tech unDNEMO.
Page 19
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
5.1 – Device Specifications
Dante Network
Physical Level:
Ethernet
Connector(s):
Dual RJ-45
Cable Quality:
CAT-5e or better
Transmission
Speed:
1000 Mbps
Supported
Sample Rates
48kHz
Minimum Dante
Network Latency
1ms
Power Requirements
PoE
802.3af PoE PD compliant
External Power
24V DC, center positive
barrel jack, 6.0mm OD /
2.0mm ID
Power
Consumption
< 6W Max
Cable Quality:
CAT-5e or better
Product Compliance
FCC CFR 47 Parts 15B
ICES-003
CE (EN55022)
RoHS
REACH
Physical Dimensions
Width
6.45”
Height
2.6”
Depth
6.23”
Weight
1.13 lbs
Environmental Specifications
Operating
Temperature
0 to 40 C
Audio Inputs
Input Types:
Internal electret microphone
External electret headset
microphone connectivity with
internal bias (3.5mm T-S)
Line Input: 3.5mm TRS
Input Impedance:
Line Input: 10kOhm
Maximum Input Levels:
Line Input: +12dBu
Mic Bias Voltage:
1.65V
Audio Input Performance
THD+N:
Line Input: <0.02% @ 1kHz
Frequency Response:
Line Input: 20Hz – 20kHz,
+/- 1dB
Audio Outputs
Speaker Type:
Internal 1” Driver
Attenuation Range
Software controlled volume
(1 to 10(max), 6dB per step)
Headphone Output
Stereo 3.5mm TRS
Maximum
Output Levels:
Speaker: 1W @ max volume
Headphone: 1Vrms into 32
Ohms (minimum load)
Audio Output Performance
THD+N:
<0.01% @ 1kHz, input signal
3dB below maximum
Frequency Response
Headphone: 20Hz – 20kHz
+/- 1dB
Page 20
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
APPENDIX A – Reference Documents
The following table lists the relevant reference documents.
Document Title
Revision
Page 21
Attero Tech by QSC unDNEMO
User Manual
QSC, LLC 2020 614-00030
Document Information
Document title:
unDNEMO
Document file name:
unDNEMO_User_Manual.docx
Revision number:
<03>
Issued by:
Attero Tech
Issue Date:
4/19
Status:
Released
Revision History
Revision
Date
Author
Description of change
00_a
6/17/16
JDA
Initial Draft
00_b
6/22/16
CNL
Review and reformat
00_c
6/23/16
JDA
Cleaned up specs, comments
00_d
07/01/16
CNL
Removed RoHS table
01
07/01/16
CNL
Release Version
02
08/09/16
TMS
Max Input Level on 3.5mm TRS input changed from +12dBu to +11dBu
02_a
10/16/17
CNL
Bug #3485 – Update manual regarding UTP/STP cable
02_b
3/14/18
SGG
Warranty Update/Factory Reset Procedure
Loading...