QSC Audio 122 User Manual

1675 MacArthur Blvd., Costa Mesa, CA, 92626 USA
Main Number [phone] Sales & Marketing [phone] or toll free (USA only) [phone]
Customer Service(714) 957-7150 or toll free (USA only) [phone]

HPRi Loudspeaker Accessory User Manual

HPR YOKE 122 Yoke Bracket

Introduction

This yoke mount is specifically for mounting the QSC HPR 122i loudspeaker to a structural support element (light­ing or soundstage truss or other load bearing truss, etc.). Additionally, it may be used vertically oriented atop a
35mm loudspeaker pole mount allowing up- or down-tilt. It is not to be used as a wall mount or other attachment
to non-load rated structure.

Contents

•Steel Yoke Bracket (1)

•M10 Hex-head Bolts (2)

•Rubber Flat Washers (2)

•Steel Flat Washers (2)

•Steel Lock Washers (2)

•This User Manual

Important Safety Information

Do not use this yoke bracket to attach the HPR 122i to a wall or other architectural element!

Attach the base of this yoke bracket to the load-bearing structure using appropriate load­rated hardware approved for the application.

WARNING! Before placing, installing, rigging, or suspending any speaker product, inspect all hard­ware, suspension, cabinets, transducers, brackets and associated equipment for damage. Any
missing, corroded, deformed or non-load rated component could significantly reduce the strength
of the installation or placement. Any such condition severely reduces the safety of the installation
and should be immediately corrected. Use only hardware which is rated for the loading conditions
of the installation and any possible short-term unexpected overloading. Never exceed the rating of
the hardware or equipment.

Figure 1- Attach yoke bracket
to the side rigging points.

Consult a licensed, professional engineer when any doubt or questions arise regarding a physical
equipment installation. Ensure all local, state, and national regulations regarding the installation,
operation, and safety of this equipment are understood and adhered to.

Attaching the Yoke to the Loudspeaker

The yoke bracket is designed to attach only to the side rigging points on the loudspeaker as shown in Figure 1.

1- To attach the bracket to the loudspeaker enclosure, you
must first remove the M10 bolts from the enclosure’s side rig­ging points (6mm hex wrench required).

2- Attach the yoke to the rigging points using the M10 Hex
Head Bolts included with the bracket. Note the hardware order
shown in Figure2. Ensure the rubber flat washers are installed
between the bracket and the loudspeaker enclosure. The steel
flat and lock washers are to be installed between the bolt and
the outside bracket surface. The lock washer is the outermost
washer, located directly under the head of each bolt.

3- Tighten bolts snuggly, just to the point where the yoke is
held in place but able to rotate. Set desired tilt and tighten the
two M10 bolts to secure the loudspeaker in place.

Rubber washers

Bolt

Lock washer

Flat washer

*TD-000247-GP*

Figure 2- Hardware
installation order.

TD-000247-00 rev.A
© Copyright 2007 QSC Audio Products, Inc.
QSC® is a registered trademark of QSC Audio Products, Inc.
“QSC” and the QSC logo are registered with th e U.S. Patent and Trademark Office

Installation Options

The yoke bracket can be used to support the HPR 122i in several ways.

Yoke above loudspeaker enclosure (Figure 3) - If using the yoke

bracket positioned above the enclosure, attach to the enclosure using the outer­most set of mounting holes in the bracket’s arms.

If single point bracket attachment to the support structure is
used, ensure the support hole just right of the loudspeaker‘s
centerline is used in order to keep the enclosure’s weight bal­anced.

Yoke below loudspeaker enclosure (Figure 4) - If using the yoke

bracket positioned below the enclosure, attach the yoke to the enclosure using
either set of mounting holes in the bracket’s arms.

Yoke behind loudspeaker enclosure (Figure 5) - If using the

yoke bracket positioned behind the enclosure, use the innermost set of mount­ing holes in the bracket’s arms. Do not use the outermost set of holes!

If the yoke bracket is behind the loudspeaker, the inner set of
mounting holes (on the brackets arms) must be used.

Figure 3- Yoke
above enclosure.

Figure 4- Yoke
below enclosure.

Single point
attachment
hole.

Third party loudspeaker pole stand mount (Figure 6) - The

yoke bracket may be attached to a third party loudspeaker pole stand mount.
This allows the user to mount the HPR 122i on a 35mm loudspeaker pole and be
adjusted for up- or down-tilt, as required. The bracket’s mounting hole pattern
fits most available mounts. For a list of compatible pole mounts, please visit
http://www.qscaudio.com.

When attaching the pole mount, use the pole mount holes that
result in the center of the pole being offset to the right of the
loudspeaker’s centerline (as viewed from the front of the
enclosure).

Do nothing- Keep in mind, if you do not know what you are doing, don’t

mount this loudspeaker to anything, including the yoke bracket. Consult profes­sional assistance if unsure about any loudspeaker mounting or suspension topic
or procedure.

Warranty

(USA only; other countries, see your dealer or distributor)

Disclaimer

QSC Audio Products, Inc. is not liable for any damage to amplifiers, or any other equip­ment that is caused by negligence or improper installation and/or use of this loud­speaker product.

QSC Audio Products 3 Year Limited Warranty

QSC Audio Products, Inc. (“QSC”) guarantees its products to be free from defective
material and / or workmanship for a period of three (3) years from date of sale, and will
replace defective parts and repair malfunctioning products under this warranty when
the defect occurs under normal installation and use - provided the unit is returned to our
factory or one of our authorized service stations via pre-paid transportation with a copy
of proof of purchase (i.e., sales receipt). This warranty provides that the examination of
the return product must indicate, in our judgment, a manufacturing defect. This war­ranty does not extend to any product which has been subjected to misuse, neglect, acci­dent, improper installation, or where the date code has been removed or defaced. QSC
shall not be liable for incidental and/or consequential damages. This warranty gives you
specific legal rights. This limited warranty is freely transferable during the term of the
warranty period.

Figure 5- Yoke
behind enclosure.

Note! Use inner set
of mounting holes
for attaching
enclosure to
bracket arms.

Figure 6- Yoke mounted
on third-party loud­speaker pole mount.

Note! Use the pole
mount holes (shown) to
the right of the loud­speaker’s centerline as
viewed from the front of
the enclosure. This will
better balance the loud­speaker over the pole.

Customer may have additional rights, which vary from state to state.

In the event that this product was manufactured for export and sale outside of the
United States or its territories, then this limited warranty shall not apply. Removal of the
serial number on this product, or purchase of this product from an unauthorized dealer,
will void this limited warranty. Periodically, this warranty is updated. To obtain the most
recent version of QSC’s warranty statement, please visit www.qscaudio.com. Contact
us at 800-854-4079 or visit our website at www.qscaudio.com.