Current draw is the amount of AC current an amplifier demands while it is operating. Measurements are provided for various loads at idle, 1/8 of average full power, 1/3 of average full power,
and full power, with all channels driven simultaneously. The figures shown on this sheet are for 120 VAC usage; for 230- and 100-volt operation, see the companion sheets. For typical usage,
use the idle and 1/8 power figures. Where an asterisk (*) appears, the data was not available at press time. The designations "na" and "nr" respectively mean "not applicable" to the particular
amplifier model and "not rated" for the particular load impedance.
Idle1/8 Power1/3 PowerFull Power
Current draw at
idle or with
very low signal
level.
ISA 2800.32.64.16.23.86.29.76.71116.5
ISA 4500.43.55.99.15.49149.716.225.4
ISA 7500.54.5710.38.313.320.516.126.540.7
ISA 13501.26.410.114.512.520.130.625.542.265.7
ISA 300T0.32.64.16.25.53.86.29.78.46.71116.512.9
ISA 500T0.43.55.99.16.95.491412.79.716.225.419.1
ISA 800T0.54.5710.38.58.313.320.516.516.126.540.731.7
Current draw at 1/8 of full power is measured with pink
noise as a signal. It approximates operating with music or
voice with light clipping and repesents the amplifier's
typical "clean" maximum level, without audible clipping.
Use these figures for typical maximum level operation.
Current draw at 1/3 of full power is measured with pink
noise as a signal. It approximates operating with music or
voice with very heavy clipping and a very compressed
dynamic range.
Current draw at full power is measured with a 1 kHz sine
wave. However, it does not represent any real-world
operating condition.
EX 8000.42.94.56.545.88.5711.517
EX 12500.43.55.27.54.56.59.3101522
EX 16000.54.5710.5710.51514.522.530
EX 2500157.5118.61522193141
EX 400015.78.51210.21724254058
Page 3
Amplifier Current Draw—230 VAC
Current draw is the amount of AC current an amplifier demands while it is operating. Measurements are provided for various loads at idle, 1/8 of average full power, 1/3 of average full power,
and full power, with all channels driven simultaneously. The figures shown on this sheet are for 120 VAC usage; for 230- and 100-volt operation, see the companion sheets. For typical usage,
use the idle and 1/8 power figures. Where an asterisk (*) appears, the data was not available at press time. The designations "na" and "nr" respectively mean "not applicable" to the particular
amplifier model and "not rated" for the particular load impedance.
Idle1/8 Power1/3 PowerFull Power
Current draw at
idle or with
very low signal
level.
ISA 2800.151.32.053.11.93.14.853.355.58.25
ISA 4500.21.752.954.552.74.574.858.112.7
ISA 7500.252.253.55.154.156.6510.258.0513.2520.35
ISA 13500.63.25.057.256.2510.0515.312.7521.132.85
ISA 300T0.151.32.053.12.751.93.14.854.23.355.58.256.45
ISA 500T0.21.752.954.553.452.74.576.354.858.112.79.55
ISA 800T0.252.253.55.154.254.156.6510.258.258.0513.2520.3515.85
Current draw at 1/8 of full power is measured with pink
noise as a signal. It approximates operating with music or
voice with light clipping and repesents the amplifier's
typical "clean" maximum level, without audible clipping.
Use these figures for typical maximum level operation.
Current draw at 1/3 of full power is measured with pink
noise as a signal. It approximates operating with music or
voice with very heavy clipping and a very compressed
dynamic range.
Current draw at full power is measured with a 1 kHz sine
wave. However, it does not represent any real-world
operating condition.
EX 8000.21.452.253.2522.94.253.55.758.5
EX 12500.21.752.63.752.253.254.6557.511
EX 16000.252.253.55.253.55.257.57.2511.2515
EX 25000.52.53.755.54.37.5119.515.520.5
EX 40000.52.854.2565.18.51212.52029
Page 5
Amplifier Current Draw—100 VAC
Current draw is the amount of AC current an amplifier demands while it is operating. Measurements are provided for various loads at idle, 1/8 of average full power, 1/3 of average full power,
and full power, with all channels driven simultaneously. The figures shown on this sheet are for 120 VAC usage; for 230- and 100-volt operation, see the companion sheets. For typical usage,
use the idle and 1/8 power figures. Where an asterisk (*) appears, the data was not available at press time. The designations "na" and "nr" respectively mean "not applicable" to the particular
amplifier model and "not rated" for the particular load impedance.
Idle1/8 Power1/3 PowerFull Power
Current draw at
idle or with
very low signal
level.
ISA 2800.363.124.927.444.567.4411.648.0413.219.8
ISA 4500.484.27.0810.926.4810.816.811.6419.4430.48
ISA 7500.65.48.412.369.9615.9624.619.3231.848.84
ISA 13501.447.6812.1217.41524.1236.7230.650.6478.84
ISA 300T0.363.124.927.446.64.567.4411.6410.088.0413.219.815.48
ISA 500T0.484.27.0810.928.286.4810.816.815.2411.6419.4430.4822.92
ISA 800T0.65.48.412.3610.29.9615.9624.619.819.3231.848.8438.04
Current draw at 1/8 of full power is measured with pink
noise as a signal. It approximates operating with music or
voice with light clipping and repesents the amplifier's
typical "clean" maximum level, without audible clipping.
Use these figures for typical maximum level operation.
Current draw at 1/3 of full power is measured with pink
noise as a signal. It approximates operating with music or
voice with very heavy clipping and a very compressed
dynamic range.
Current draw at full power is measured with a 1 kHz sine
wave. However, it does not represent any real-world
operating condition.
EX 8000.483.485.47.84.86.9610.28.413.820.4
EX 12500.484.26.2495.47.811.16121826.4
EX 16000.65.48.412.68.412.61817.42736
EX 25001.26913.210.321826.422.837.249.2
EX 40001.26.8410.214.412.2420.428.8304869.6
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.