Qpets SP 207 User Manual

Qpets 4 in 1 Training Collar

User Manual

Model: SP 207

Please read this guide before using

1. Antenna

2. Light

3. Shock & Vibration Indication Light

4. Shock Button

5. Vibration Button

6. Light & Whistle Indication Light

7. Light Button

8. On/Off Switch

9. Whistle Volume Switch

10. Whistle Button

11. Electrodes

12. Receiver Battery Cover/Lid

13. Power (Green) Indication Light

14. Pair (Red) Indication Light

Thank you for choosing Qpets. Our mission is to make a happy pet owner by providing
quality pet products, the lasted tools and techniques to successfully train your pet. If you
have any questions or comments, please contact the our Customer Care Center at 1-909­923-8743 or visit our website at www.lavasat.com

Table of Contents

Components……………………………………………………………............2

Quick Start Guide………………..……………………………….……3

Step-1 Prepare the remote/transmitter…………3
Step-2 Pair transmitter with the collar receiver…3
Step-3 Install the electrodes for the receiver….…4
Step-4 Adjust the collar to fit your pet………………4

How to check the static shock function…………………..…5
How to change the batteries……………………………………..5
Important Tips…………………………………………………………..5
Customer Support Center………………………………………….6

1

Components:

1 x Transmitter

(Controller)

1 x 9V 6F22

Battery(for

Transmitter)

1 x Receiver

1 x Adjustable

Collar

Strap(for

Receiver)

2 x 1.5V AAA

Batteries(for

Receiver)

2 x Pair of

Electrodes(for

Receiver)

1 x Test

Light(for test

shock

function)

1 x User

Manual

This is an effective 1 pet training system for small and medium pet which weight under
50 pounds, specially designed for those who wish to train their pet. It features an easy­to-use transmitter, 4 different functions (static shock, vibration, whistle and light), Up to
200 feet range.

2

Quick Start Guide

Step 1: Prepare the Remote Transmitter

Follow the Positive (+) and Negative (-) signs inside
the transmitter. Insert the 1 x 9V 6F22 Battery into
the transmitter correctly. Turn on the switch where
on the side of the transmitter.

Step 2: Pair Transmitter with the Collar Receiver

1. Follow the Positive (+) and Negative (-) signs inside Receiver. Insert the 2 x 1.5V

AAA batteries into Receiver. The RED INDICATION LIGHT starts blinking and the
Green indication light keeps on.

Step 2-1

2. Press Vibration Button on the transmitter within 20

seconds while the Red Indication Light is blinking on
the receiver. The receiver will vibrate when
successfully paired with transmitter and the RED
Indication light will stay ON. Repeat step 2 if the
receiver still does not paired.

NOTES:

 Press Vibration Button on the transmitter within 20 seconds while the Red

Indication Light is blinking on the receiver. The receiver will vibrate when

successfully paired with transmitter and the RED Indication light will stay ON.

Repeat step 2 if the receiver still does not paired.

3

 Please always install battery for the Transmitter BEOFE install batteries for the

receiver. The Transmitter has to be power on first, then the receiver will be

able to receive the pair code from transmitter.

Step 3: Install the Electrodes for the Receiver.

Randomly pick one pair of electrodes and screw for receiver. (Please pick the same
size electrodes for the receiver.)

Step 4: Adjust the collar to fit your pet.

To ensure a proper fit, please follow the steps below:

1. Put the strap on the receiver.

2. With your pet standing, center of the collar receiver where contact points are

underneath your pet’s neck, touching the skin.

3. The collar receiver should fit snugly, yet loose enough to allow one finger to fit

between the strap and your pet’s neck. If the strap is too long for your pet, cut
off the excess length.

4. Allow your pet to wear the collar for several minutes and then re-check the fit.

Check the fit again as your pet becomes more comfortable wearing the collar
receiver.

NOTES:

 The Transmitter and Receiver will enter Sleep Mode automatically if there is no

activity detected within 2 minutes.

 To wake up the receiver, please gently shack the receiver and the indication

lights of receiver will back on again.

We would recommend you to use the vibration function first before starting the
Shock and always start from the lowest level of shock.

4

How to Check the Static Shock Function

1. Use the Test Light attach on the both side of

Electrodes (Metal).

2. Press Shock Button, the TEST LIGHT will blink

or keeps on.

How to Change the Batteries

 Please replace the Transmitter’s battery when

the indication light does not light up on the transmitter or transmitter stop
working.

 Please replace the receiver’s batteries when the Green Indication Light does not

light up on the receiver or receiver stop working.

Important Tips:

(Please Read)

1. The valid distance of remote control means the straight-line distance between

the transmitter and the receiver without obstacles in between. If there are
interference signals or signal screening around, the actual remote control
distance may vary.

2. The lifetime of the batteries vary according as how often you use the product.

Your first battery may not last as long as you expect.

3. The whistle function design for you to call your pet, this is not a warning beep

function for the receiver.

4. This product is for pet training. Good effect can only be achieved after a period

of training.

5. This product is a wireless transmitting device; you MUST NOT use the remote

control system in places like petrol stations or hospitals where mobile phones
are prohibited. Patients using heart pacemaker are forbidden to use this
product. If some products have the same frequency as this product, the
receiver might not work correctly.

6. The Electrodes have to directly touch pet’s skin as it is very important to

effective training.

7. This product is only for Pet Training, It is not a Regular Pet Collar. Please

remove it from your pet at least 8 hours out of every 24 hours.

8. The Device is not waterproof.

9. Please turn off power for saving battery life when do not use.

5

Customer Support Center

Tel: [phone]
Monday – Friday 8:30AM – 5:00 PM Pacific Time
Email:[e-mail]
Add: LAVA Electronics Inc. 2580 E Philadelphia ST #D, Ontario, CA 91761

This product has a limited Manufacturer Warranty. Details of the warranty can be found
on www.lavasat.com or by calling our Customer Support Center.

Made in China

6

LAVA Electronics Inc

2580 E Philadelphia St #D

Ontario, CA 91761, USA

1-909-923-8743

www.lavasat.com

Email:[e-mail]

Copyright © LAVA Electronics Inc. 2010. All rights reserved.