QOMO 75I8 User Manual

Interactive Touch Screen

User Manual

Please properly keep the manual for further reference. This is the general user manual for all interactive touch screens. Therefore, it may be different from the actual product.

Welcome:

Thanks for purchasing this product. Please read the instructions carefully before using this product.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiver.

● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

● Consult the dealer or an experienced radio/ TV technician for help.

The symbol of the crossed out wheeled bin indicates this product should not be placed in municipal waste. Instead, you need to dispose of the waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.

Content

Safety Instruction .................................................................................................................... 1

Installation Requirement ......................................................................................................... 3

Introduction ............................................................................................................................. 6

Basic Operation ...................................................................................................................... 7

Power on ............................................................................................................................. 7

Power off ............................................................................................................................. 7

Functions of the remote control ............................................................................................... 8

Panel Buttons & Ports ............................................................................................................. 9

Operation Interface Introduction ............................................................................................ 11

Android home page ........................................................................................................... 11

Android settings ................................................................................................................ 12

Built-in PC interface .......................................................................................................... 15

Toolbar .............................................................................................................................. 16

Whiteboard software - Magicboard ....................................................................................... 17

Configuration Parameters .................................................................................................... 19

Included Accessories ........................................................................................................... 20

Troubleshooting ................................................................................................................... 21

WARNING

Disconnect the product from power supply immediately if major failures occur.

The major failures include the following:

 Smoke, peculiar smell or abnormal sound is discharged from the product.  No image or sound is displayed, or the image error occurs.  Where the mains plug or an appliance coupler is used as the disconnect device,

such disconnect device shall remain readily operable. In the preceding scenarios, do not continue to use the product, disconnect power supply immediately and contact professional staff for troubleshooting.

Do not drop liquid, metal or combustible into the product.  If any liquid or metal is dropped into the product, power off the product and disconnect power supply, then contact professional staff for solutions.  Pay attention to the children when they are close to the product.

Do not damage the power cable.

● Do not damage, change, wind, bend, heat or drag the power cable forcibly.

● Do not put weights (such as the product itself) on the power cable.

● Do not drag the cable forcibly when you pull out the power plug. If the power cable is

damaged, please contact the local distributor to repair or replace it.

Put the product on a stable surface. An unstable surface includes and does not limit to an inclined plane, a shaky stand, desk or platform, which might cause the turnover and damage.

Use the battery correctly.  Galvanic corrosion, electric leakage and even fire may be caused by improper battery usage.  It is recommended to use the designated type of battery and install the battery by correct electrodes (positive and negative electrodes).

 Do not install and use new battery with the used one.  Take out the battery if the remote control is not used for a long period.  Do not expose the battery under overheated environments such as sunlight and

firing.  Dump the used battery based on local regulations.

WARNING

Do not open the cover or change the product by your own.

High voltage components are installed in the product. When you open the cover, high voltage, electric shock or other dangerous situations may occur. If inspection, adjustment or maintenance is required, contact the local distributor for help.

Safety Instruction

For your safety, please read the following instruction before you use the product. Serious injury or

property loss may be caused by improper operations. Do not try to repair the product by your own.

1

Use the specified power supply.

● Do not use any types of power cables other than the one provided with the product to

prevent the product from being damaged.

● Use a three-wire socket and ensure that it is properly grounded.

● Pull out the power plug from the socket if the product is not used for a long period.

Before you move the product, disconnect all external connections and separate all toppling preventing devices.

Move the product carefully to prevent it from being hit or squeezed, especially the screen, which may cause injury if broken.

Clean the dust and metal on the power plug regularly.

● When you are cleaning, fire or electric shock may be caused if the product is

powered on.

● Keep in mind to pull out the power plug before cleaning it by using a dried cloth.

Do not put items on the top of the product.

● Do not put items, such as a container for liquid (a vase, flowerpot, cosmetics or liquid

medicine), on the top of the product.

● If any water or liquid is spilled on the product, short circuit may occur and cause fire

or electric shock.

● Do not tread on the product or hang any items on the product.

Do not install the product in an improper place.

● Do not install the product in humid places, such as the bathroom, the shower room,

the place near windows or outdoor environments where experience rain, snow or other harsh weather. The product installation is also required to avoid a place around by hot spring vapor. The preceding environments may cause faults or electric shock under extreme conditions.

● Do not put exposed fire source, such as an ignited candle, on the product.

Pull out the power plug during thunderstorms.

● Do not touch the product when lighting to avoid electric shock.

● Install or place components which power supply voltage is high enough to cause

personal injury in places out of the reach of children.

WARNING

Do not cover or block up any vents on the product.

● The overheated components may cause fire, damage the product and shorten the

service life.

● Do not put the venting surface of the product facedown.

● Do not use a cloth such as table cloth to cover the product.

Do not touch the power cable with wet hands to avoid electric shock.

CAUTION

Do not install the product in high temperature environments.

● Do not install the product near heat source, such as the radiator, the heat reservoir,

the stove or other heating devices.

● Do not expose the product under sunlight, which may cause high temperature and

subsequent faults in the product.

2

For transport:

● Pack the product for mobility or maintenance by using the cartons and cushioning

material provided with the product.

● Vertically move the product during transport. The screen or other components are

easily broken if the product is moved by an improper way.

Keep away from the product when you use a radio. The product design to prevent radio interference complies with the international EMI standard. However, the interference still exists and causes noise in the radio.

● If noise occurs in the radio, try the following solutions.

● Adjust the direction of the radio antenna to avoid the interference from the product.

● Keep the radio away from the product.

Advice for watching:

● Use the product in an environment with comfortable light. It is harmful to your eyes to

watch in a too bright or too dark environment.

● Relax your eyes after a period of time for watching.

● When you are watching, the distance which is 3 to 7 times of the screen height

should be kept, and it is the best distance to protect eyes and prevent eyestrain.

● Adjust the volume to an appropriate level, especially at night.

Ventilation

requirements

Distance to the surface for installation (cm)

Nominal power

Greater than 100 W

Left and right sides

Top

Bottom

Back

10

20

10

Installation Requirement

Bearing

You can install the product in an unfixed or a wall-mounted way based on your needs. The wall-

mounted way can save a large amount of space.

If the product is installed in an unfixed way, use the designated hanger or holder. If you want to

use a self-made hanger or holder, ensure that the bearing capacity of it is at least four times of the weight of the product, and the product is installed stably on it.

If the product is installed in a wall-mounted way, the bearing capacity of the surface for

installation must be at least four times of the weight of the product. If the surface for installation is the wall or the ceiling of a building, the surface must be made of solid bricks, concrete or other materials with equal intensity. If the product is installed on a surface made of loose material such as an old brick wall, wood plank wall, solid brick wall, or a metal or non-metal structure surface, or a surface with a thick decoration layer, take necessary consolidating measures to ensure that the product is stably installed.

Ventilation

If the product is installed inside a wall or a cabinet, in addition to the preceding requirements, the ventilation area around the bottom, top and two sides must be at least 50% of the sealing surface to ensure proper ventilation.

3

Note: 1. When the product is installed in a wall-mounted way, the screws need to be installed

deeper than 10 mm in the way.

2. Do not block ventilation vents.

4

Use a level to locate the holes in horizontal line and mark with pencil where the holes will be located. Then drill holes in the wall.

Insert wall plugs into the mounting holes. Push the self-tapping screws through the bracket into the wall plugs and tighten the screws.

Attach the mounting arms to the back of screen with the screws.

Hang the screen and let it settle into the bracket. Ensure that it is firmly in place.

Level

Installation diagram

Note: The horizontal and vertical distance of mounting holes on the back of screen must be within the required distance of bracket.

5

Introduction

As our latest independently developed and produced human-machine interactive product, the

Journey 13 series interactive touch screen is a multi-functional display for interactive teaching, digital demonstration, multi-media presentation, touch operations and handwriting. They are well designed and produced to meet the needs of education and corporate applications, and provide a user-friendly experience, digital intelligent control as an ideal equipment for schools and companies. You can use your fingers or opaque objects to write, edit and delete any things on the screen.

The product features are as follows:

• Specially designed for teaching and meeting systems.

• With high brightness and high contrast, the display is visible under strong sunlight or in outdoor

environments.

• Enter into Eco mode with one-touch button to reduce the power consumption.

• Adopt advanced infrared array scanning and sensing technology, HID driver-free, meaning the

product is activated soon after it is powered on.

• Multi-signal sources can be previewed in the window and be switched by touching the screen.

• Vector-based image-editing software with features like high compression and distortion free.

• Multiple pen tools, line styles and colors selections.

• Support real time on-screen editing.

• Shape recognition turns hand-drawn shapes into perfect versions.

• Save files in various formats, including PDF, JPEG, PNG, BMP and etc.

• Multi-touch screen enables several users use the screen together.

• User management enables you to add a new user, delete a user, switch a user and edit user

information etc.

• Support handwriting recognition including English, Chinese, numbers and special characters.

6

Power Indicator

Status

No light

Power off

Red

Standby

Green

Power on

Basic Operation

Power on

 Power the interactive touch screen with the 100V-240V 50Hz/60Hz AC power supply.  Connect the panel to the power supply. Switch on the rocker switch (on the left bottom of the

rear of the panel, next to the power port) to enter the standby status. The power indicator turns red.

 Press power switch on the control panel or Power on the remote control to turn on the display

and built-in PC simultaneously. The power indicator turns green.

Power off

 Press ECO on the control panel to temporarily turn off the display.  Press power switch on the control panel or Power on the remote control to enter the standby

status. The power indicator turns red.

 In the standby status, switch off the rocker switch to turn off the touch screen.

1. Disconnect the touch screen from power after the touch screen enters standby status. Otherwise, the screen may be damaged. A sudden power failure may damage the touch screen.

2. Frequent power on and off in a short time may cause faults.

Status of the power indicator is as follows:

7

1. Power on or standby

2. Mute

3. Change channels or enter numbers

4. Return

5. P. MODE: Picture mode SMODE: Sound mode

6. Signal source selection

7. Show the current signal source

8. VOL+/ VOL-: Increase/decrease volume

9. CH+/ CH-: Change channel

10. Sleep mode NICAM: Select the sound tracks ASPECT: Selects picture aspect EPG: Electronic program guide

11. Up/down/right/left direction buttons OK: Confirm

12. Show or hide menu

13. Quit the current interface

14. Play/Pause

15. Rewind or replay certain scenes

16. Buttons for image & text editing

17. Buttons for channel editing

Functions of the remote control

8

Android USB port

Built-in PC USB port

HDMI port used to connect an external display device

Power indicator:

 Press power switch on the control panel. The power indicator turns green.  Press power switch on the control panel to enter the standby status. The power indicator turns red.

Enter/Return to Android home page

Front ports:

Decrease volume OSD button:

Return to previous interface

Increase volume OSD button:

Enter ECO mode to turn off the display

Enter/Exit the OSD menu

Enter/Exit signal source menu

Power switch: on or standby

Panel Buttons & Ports

Buttons & ports on the front panel

9

Ports on the rear panel

Ports on bottom of motherboard

Ports on right side of motherboard

10

Setting

Click the icon to enter the Android setting interface.

Applications

LocalMM

Browser

Click the icon to enter the Android application interface.

Built-in browser

Copy and play local files on Android.

Operation Interface Introduction

Android home page

Interface Introduction

1. Click the signal source in part ① and its thumbnail will be shown in part ②. Then click part ② to enter its corresponding signal source.

2. Part ③ includes four icons Settings, Browser, Applications and LocalMM.

11

Network and equipment (Figure 2)

Common function (Figure 1)

Figure 1

Press on the remote control or click the item directly to select the one you want to change its setting.

Press on the remote control or click the item directly to select the one you want to change its setting. Connect the network with WIFI, Ethernet or hotspot. Click WLAN to connect it with WIFI, choose a network and enter WIFI password.

Android settings

Sound setting Click Sound and the icon pops up. Slide right or left to increase or decrease the

volume.

Brightness adjustment Click Brightness level and the icon pops up. Slide left or right to adjust the

brightness.

Font size

Click Font size and a window pops up. Then set your desired font size.

Wallpaper setting Click Wallpaper to set dynamic or static wallpaper.

12

Storage (Figure 3)

Figure 3

Press on the remote control or click the item directly to select the one you want to change its setting.

Language & input (Figure 4)

Press on the remote control or click the item directly to select the one you want to change its setting.

Use storage for more detailed information about its usage.

Figure 2

Change system language and keyboard input language.

13

Figure 4

Date & Time (Figure 5)

Press on the remote control or click the item directly to select the one you want to change its setting.

About machine (Figure 6)

Press on the remote control or click the item directly to select the one you want to change its setting.

Figure 5

Figure 6

Change time format, time zone and etc.

Click About machine to check date of production, network, model and etc.

14

Built-in PC interface

1. Select PC signal source to enter the PC interface. The following three ways are used to select a

signal source channel.

 Swipe your finger up from the bottom edge to bring up a toolbar then click input.  Press SOURCE button on the remote control.

 Press button on the front control panel.

In the signal source page, select a channel and press OK or click the channel icon directly to enter it.

2. Operate the built-in PC just like operating an ordinary computer.

3. Shutdown the PC before you press power switch on the front control panel. Do not power off a

running PC suddenly to avoid data lose.

Input operation

1. Click anywhere on the screen;

2. A floating keyboard appears on the left;

3. Drag the keyboard to the middle and release it until the keyboard is invoked.

15

Click task to view and manage the recently-opened programs ②

Press buttons on the remote control and press OK or click the window to enter the

program. In the task, you can view current running programs, switch and end programs.

Vol +: Increase the volume

Menu: Open settings menu

Task: Switch running programs

Home: Return to Android home page

Back: Return to previous interface

Input: Change signal resource channel

Vol - : Decrease the volume

Light +: Increase the brightness

Light - : Decrease the brightness

S-shot: Take a screenshot and

automatically save it

Click input and get the pop-up signal resource channels ①

Press buttons on the remote control and press OK or click the channel icon

directly to enter it. Channel icon is highlighted when selected.

Toolbar

This toolbar can be invoked in any system interface. Swipe from the bottom of screen and this toolbar appears.

16

Set background color

Select pen color

Delete the slide

Add a new slide

Drag the page to reveal more of the page

Rectangular selection

Undo

Redo

Eraser

Unfold/fold the toolbar

Text

Save

Open local file

Whiteboard software - Magicboard

The whiteboard provides the writing function. In the whiteboard program, you can use a pen and select its color to write and use an eraser to erase contents on the whiteboard. You can also save the content on the whiteboard.

1. Click the icon on the Android application interface to go into the whiteboard mode. Click the

floating icon to unfold the toolbar.

Tools on the toolbar are listed as follows:

17

2. Rectangular selection: select rectangular regions of the contents to zoom in/out, move, delete and etc as shown in ②.

3. Text: Click Text and a box pops up. You can enter the text and change font size and color as shown in ③.

4. Save & open files: Save a file with a default name or you can type a new file name. Click “open local file”， you can select your desired file from a pop-up window as shown in ④.

.

18

Model

QIT1355

QIT1365

QIT1375

QIT1385

Backlight

LED

Active/Display Size

55"

(1209.6 * 680.4 mm)

65"

(1430.5 * 805.5mm)

75"

(1651.3 * 928.6 mm)

85"

(1874.6*1055.6 mm)

Display Ratio

16:9

Resolution

1920 *1080px

1920*1080px

3840*2160px

Display Colors

10bit

Brightness

350cd/m2

350cd/m²

400cd/m²

Contrast

4000:1

5000:1

4000:1

Response Time

6ms

6.5ms

Refresh Frequency

120Hz

Speaker Output Power

15W*2

Working Voltage

100-240V，50/60Hz

Power Consumption

Maximum:130W

Standby mode:≤1W

Maximum: 160W

Standby mode:≤1W

Maximum: 230W

Standby mode:≤1W

Maximum: 400W

Standby mode:≤1W

Inputs / Outputs

Input: AV *1; YPBPR *1; MIC*1; VGA(15 pin D-Sub)*1; HDMI 1080P *2; ( Only QIT1385 has HDMI 4K2K*1; ) Output: AV*1; HDMI 1080P*1;Audio Output Earphone*1; Port: RS232*1; SD CARD*1; PC-Audio*1; SPDIF*1; WIFI; RJ45*1; USB2.0*2; USB3.0*1; USB touch* 1; Front

HDMI*1; Front USB-PC*1; Front USB-Android*1; TV*1;

Multimedia File Formats Support

MPEG1，MPEG2，MPEG4，H264，RM，RMVB，MOV，MJPEG

Touch

Touch Size

1209.6 *680.4mm

1443.5 * 818.5mm

1720 * 942mm

1874.5 * 1056mm

Touch Resolution

4096*4096

Touch Surface

Anti- Glare Glass

Touch Sensor

IR

HID Support

HID

Touch Points

10 points

Writing Tools

Pen or Finger

Scan Speed

15ms

Cursor Speed

125 dots/s

Response Time

<8ms

＜8ms

Positioning Accuracy

1mm

Communication Interface

USB

Transportation/Storage

Storage Temperature/Humidity

-20℃~60℃/10%～90%

Working Temperature/Humidity

0℃~50℃/10%～90%

0℃~40℃/10%～90%

0℃~50℃/10%～90%

Mount ( optional )

Wall-mounted/Stand

Outline Dimension

1262.2*776.3*78.8mm

1488.9*912.2*119.7 mm

1763.4*1066.7*114.4mm

1980 *1185*107.4mm

Packing Dimension

1466.8*900.6*230mm

1710*1160*320 mm

1935*1225*280 mm

2130*1355*350 mm

Net Weight

46kg

50kg

78kg

112kg

Gross Weight

52kg

66kg

102kg

144kg

OPS Slot

Yes

Android System

Cortex A7 Quad Core CPU

Cortex A7 Quad Core

CPU

Built-in Wifi

Yes

Speaker Position

Forward-facing

Configuration Parameters

19

Picture

Name

Quantity

Remote control

*1 Pen

*2 Pointer

*1

1.8m power cable

*1

5m HDMI cable

*1

5m USB cable

*1 Bracket

*1

Antenna sticks for PC and

Android

*2

Included Accessories

20

Problem

Cause

Solution

The service program fails to be connected.

The driver program isn't properly installed.

Install the driver program properly.

The USB port (lead) is not connected or is faulty.

Change the USB lead or check if the USB port is faulty.

Infrared tube is obscured.

Make sure infrared tubes have not been obscured.

Repositioning is required every time the panel is switched on.

The computer is equipped with a recovery card.

Disable computer protection and perform the positioning again.

The positioning is inaccurate.

The positioning is not performed properly.

Press Auto on the remote control to show the full screen, and use the pen provided with the panel to perform positioning again.

The cursor of the pen is unstable when the pen is used.

The writing method is incorrect.

You are advised to use the pen rather than a finger to write. Hold the pen as far to the nib as possible. The angle between the pen and display needs to be greater than 60 degrees. Do not touch the display with your sleeve or wrist.

Strong light or infrared interference exists.

Remove the interference source or change the using environment.

The handwriting is discontinuous. (Part of the handwriting cannot be displayed.)

The writing method is incorrect.

You are advised to use the pen rather than a finger to write. Hold the pen as far to the nib as possible. The angle between the pen and display needs to be greater than 60 degrees. Do not touch the display with your sleeve or wrist.

The covering area of the nib does not meet the requirement or the nib is too small.

Change the nib or use a pen with larger covering area.

Infrared tube is obscured.

Check if infrared tubes are obscured.

Strong light or infrared interference exists.

Remove the interference source or change the using environment.

The handwriting can’t be displayed.

The color of the pen is the same as or similar to the background color.

Change the color of the pen.

Your hand or other objects are on the display when you are writing.

You are advised to use the pen rather than a finger to write. Hold the pen as far to the nib as possible. The angle between the pen and display needs to be greater than 60 degrees. Do not touch the display with

Troubleshooting

21

your sleeve or wrist.

Strong light or infrared interference

Remove the interference source or change the using environment.

The writing method is incorrect.

You are advised to use the pen rather than a finger to write. Hold the pen as far to the nib as possible. The angle between the pen and display needs to be greater than 60 degrees. Do not touch the display with your sleeve or wrist.

No sound is played and no image is displayed.

● Check whether the power plug is inserted into the power socket and whether the panel is powered on.

● Check whether the rocker switch on the interactive panel is switched on.

● Check whether the Standby button on the panel is pressed.

● Check whether the video and audio input cables are connected

correctly.

● Check whether the panel is switched to the right signal source.

● Check the settings on image brightness and contrast.

● Check the volume.

Image is displayed properly, but no sound is played.

● Check the volume.

● Check whether the Mute button on the remote control is pressed.

● Check whether the audio cable between the PC and interactive

panel is connected correctly.

No image is displayed or the image is black and white.

● Modify the color settings.

● Check the color system.

The PC cannot be started. (This scenario is applicable only to panel models operating with the PC.)

● Check whether the PC adapter is correctly connected and whether the PC is powered on.

● Check whether the PC is connected correctly to the interactive panel.

866-990-QOMO | 46950 Magelan Dr, Wixom, MI 48393 | info@qomo.com /qomosolutions Copyright ©2016 Qomo. All rights reserved. This document may not be copied in any form without permission from Qomo. Information in this document is subject to change without notice.

QOMO may modify the user manual without prior notice. If you discover any unclear presentation, mistake or omission in this manual, please contact us immediately. QOMO is not liable for any loss or damage if you fail to contact us.

22

§ 15.19 Labelling requirements.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

§ 15.21 Information to user.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

§ 15.105 Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

*RF warning for Mobile device:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

QOMO 75I8 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual