Qmark FRP, FRS - 2 User Manual [en, es, fr]

MECHANICAL ACCESSORIES

FOR

RP / RS SERIES

INFRARED HEATERS

Dear Owner,
Congratulations! Thank you for purchasing this new heater manufactured by a division of Marley

Engineered Products. You have made a wise investment selecting the highest quality product in the heat­ing industry. Please carefully read the installation and maintenance instructions shown in this manual.
You should enjoy years of efficient heating comfort with this product from Marley Engineered Products...
the industry’s leader in design, manufacturing, quality and service.

... The Employees of Marley Engineereed Products

Read Carefully - These instructions are intended to sup-

plement and be used in conjunction with the instructions pro­vided with the heater. Failure to adhere to the instructions
could result in in death, serious personal injury, fire, or per­manent damage to heater.

To prevent a possible electric shock, always disconnect
power to heater at main service panel, breaker, or fuse box
before attempting to install or service the heater, or install
these accessories.

.

Installation & Maintenance Instructions

SAVE THESE INSTRUCTIONS

WARNING

!

WIRE GUARD

Reference Figure 1.

1. Drill

5

/32” diameter holes at the

dimple locations shown.

2. Install heating elements in
accordance with the instruc­tions provided with the ele­ments.

3. Position wire guard onto heater
as shown and attach to heater
(into the

5

/

32

” holes drilled in

step 1) using the #10 scews
provided.

4. Secure wire guard to heater
using #10 screws provided.

RED VYCOR SLEEVE

Note: To be used on Quartz
Lamp elements only.

Do NOT handle Quartz lamp
elements with bare hands, as
salt in perspiration may deterio­rate the quartz and result in a
premature failure.

1. Attach one end of quartz lamp
element as indicated by instruc­tions supplied with elements.

2. Carefully slide Red Vycor
Sleeve over element.

3. Position element in reflector
and continue with element

installation, as indicated by
instructions supplied with ele­ments.

ADJUSTABLE TILT

MOUNTING BRACKET

Adjustable Tilt Mounting
Brackets replace the mounting
brackets supplied with the
heater enclosure.

Reference Figure 2.

1. Determine mounting location
as indicated by instructions
supplied with heater enclosure.

2. Do

NOT attach originally sup-

plied mounting brackets.

3. On a workbench or other flat
surface, attach Adjustable Tilt
Mounting Brackets to ends of
wireway cover using bolts, star
washers and nuts supplied with
heater enclosure.

4. Remove wireway cover/mount­ing brackets from wireway
base, as indicated by instruc­tions supplied with heater
enclosure.

5. Mount wireway cover/mounting
brackets to ceiling and secure
using fasteners sized to suffi­ciently support heater and any
optional accessories used.

6. Proceed with heater installation
as indicated by instructions
supplied with heater enclosure.

GOLD ANODIZED

REFLECTORS

Reference Figure 3.

1. Place the heater enclosure on
a workbench or other flat sur­face.

2. If elements are installed,
remove them at this point.
Reflector can not be replaced
with elements installed.

3. Remove the reflector attach­ment screws and keep for
reuse.

4. Applying light pressure, push
down on the bottom of one side
reflector until reflector end is
free from enclosure.

5. Rotate reflector away from
enclosure.

6. Install replacement reflector in
opposite sequence.

2

Drill Dimple Location
Typical

Reflector Attachment Screw
Typical (2 on 2 element heaters)

(4 on 3 element heaters)

Figure 1

Figure 3

Figure 2

Figure 4A

(Typical 4 Locations)

WALL MOUNTING

BRACKET

Reference Figure 4.

1. Determine mounting location per instruc­tions supplied with heater enclosure.

2. Attach heater mounting brackets (sup­plied with heater) to wireway cover per
instructions included with heater enclo­sure.

3. Secure wall angle brackets to wall using
fasteners (by others) sized to sufficiently
support heater and any optional acces­sories used.

4. Attach bracket extension arm to wall
angle bracket using screws, nuts, and
washers provided.

5.Attach heater mounting brackets to Wall
Mounting Bracket extension arm using
screws, nuts, and washers provided.

3

LIMITED WARRANTY

All products manufactured by Marley Engineered Products are war­ranted against defects in workmanship and materials for one year
from date of installation, except heating elements which are warrant­ed against defects in workmanship and materials for five years from
date of installation. This warranty does not apply to damage from
accident, misuse, or alteration; nor where the connected voltage is
more than 5% above the nameplate voltage; nor to equipment
improperly installed or wired or maintained in violation of the prod­uct’s installation instructions. All claims for warranty work must be
accompanied by proof of the date of installation.

The customer shall be responsible for all costs incurred in the
removal or reinstallation of products, including labor costs, and ship­ping costs incurred to return products to Marley Engineered Products
Service Center. Within the limitations of this warranty, inoperative
units should be returned to the nearest Marley authorized service
center or the Marley Engineered Products Service Center, and we
will repair or replace, at our option, at no charge to you with return
freight paid by Marley. It is agreed that such repair or replacement is
the exclusive remedy available from Marley Engineered Products.

THE ABOVE WARRANTIES ARE IN LIEU OF ALL OTHER WAR­RANTIES EXPRESSED OR IMPLIED, AND ALL IMPLIED WAR­RANTIES OF MERCHANTABILITYAND FITNESS FOR A PARTIC­ULAR PURPOSE WHICH EXCEED THE AFORESAID EXPRESSED
WARRANTIES ARE HEREBY DISCLAIMED AND EXCLUDED
FROM THIS AGREEMENT. MARLEY ENGINEERED PRODUCTS
SHALL NOT BE LIABLE FOR CONSEQUENTIAL DAMAGES ARIS­ING WITH RESPECT TO THE PRODUCT, WHETHER BASED
UPON NEGLIGENCE, TORT, STRICT LIABILITY, OR CONTRACT.

Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above exclusion or limitation may not
apply to you. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.

For the address of your nearest authorized service center, contact
Marley Engineered Products in Bennettsville, SC, at 1-800-642-

4328. Merchandise returned to the factory must be accompanied by
a return authorization and service identification tag, both available
from Marley Engineered Products. When requesting return autho­rization, include all catalog numbers shown on the products.

HOW TO ORDER REPAIR PARTS

In order to obtain any needed repair or replacement parts, warranty
service or technical information, please contact Marley Engineered
Products Service Center toll-free by calling 1-800-642-HEAT.

Part No. 5200-2475-000

12/99

PPD 024

Wall Mounting Bracket
(Typical For 2)

MODEL “A” in. (mm)

RP32 / RS32 24.625 (625)
RP33 / RS33 33.625 (854)
RP34 / RS34 46.625 (1184)

Figure 4

2.25”(57mm)

9.5”(241mm)

SPX Corporation
470 Beauty Spot Rd. East
Bennettsville, SC 29512 USA

“A”