Qmark 202SL User Manual [en, es, fr]
202SLB
Radiant Desk Heater
E152700
Installation, Operation & Maintenance Instructions
IMPORTANT INSTRUCTIONS
GENERAL
This radiant heater is designed to provide supplemental heat in small areas such as offices and may be used as an
under desk heater. However, care must be taken to avoid blocking heater or covering it with any thing that could allow
it to build up heat – See warnings.
WARNING
When using electrical appliances, basic precautions should
always be followed to reduce the risk of fire, electric shock,
and injury to persons, including the following:
1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid burns, do not let
bare skin touch hot surfaces.
3. Keep combustible materials such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet away from
front of heater and keep them away from the sides and rear.
4. Extreme caution is necessary when any heater is used by or
near children or invalids and whenever the heater is left
operating and unattended.
5. Always turn heater off at switch and unplug heater from outlet when not in use.
6. Do not operate any heater with a damaged cord or plug or
after the heater malfunctions, has been dropped or damaged in any manner. Discard heater, or return to authorized
service facility for examination and/or repair.
7. Do not use this heater outdoors.
8. This heater is not intended for use in bathrooms, laundry
areas and similar indoor locations. Never locate heater
where it may fall into a bathtub or other water container.
9. Do not run cord under carpeting. Do not cover cord with
throw rugs, runners, or similar coverings. Do not route cord
under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
10. Some models are provided with a three blade grounded
plug (see Figure 1). If provided with a grounded plug,
always connect to a properly grounded outlet only.
!
11. A heater has hot and arcing or sparking parts inside. Do not
use it in areas where gasoline, paint, or flammable liquids
are used or stored.
12. Check heater cord and plug connections. Faulty wall outlet
connections or loose plugs can cause the outlet or plug to
overheat. Be sure the plug fits tight in the outlet. Heaters
draw more current than small appliances, therefore overheating of the outlet may occur even if it has not occurred
with the use of other appliances. If plug outlet or faceplate
is HOT, discontinue use and have qualified electrician
check/replace the faulty outlet.
13. Always plug heater directly into a wall outlet/receptacle.
Never use with an extension cord or relocatable power tap
(outlet/power strip).
14. If this heater is to be used in damp areas such as basements or garages, a ground fault circuit must be provided.
15. Do not make holes in the heater. Damage to internal electrical components or electric shock hazards may occur and
this will void your warranty.
16. Use this heater only as described in this manual. Any other
use not recommended by the manufacturer may cause fire,
electric shock, or injury to persons.
17. This heater is provided with a tip over switch that will disconnect power to the heater if it is tilted or falls over. The
heater can only be used in the vertical position or tilted back
slightly when used with built in stand.
SAVE THESE INSTRUCTIONS
INSTALLATION INSTRUCTIONS
This heater operates in upright position only. For mounting heater to desk, apply velcro to top of heater back, one
piece near each corner. Remove backing from back of
velcro and press firmly against the desired position on the
desk. Normal position is against the desk knee-well panel
with the top of the heater at knee height. To remove, pull
bottom of heater firmly away from desk. Heater can be
restored to original position by once again attaching to
velcro. The leg on the back swings out to support the
heater when used as a portable heater.
OPERATING INSTRUCTIONS
1. Heaters are provided with flexible cord with a grounded 2
blade plug (as shown in Figure 1) and built-in ON/OFF
switch. This heater is for use at 120 V AC only.
2. An adapter as shown at C in Figure 1 is available for connecting three-blade grounding-type plugs to two-slot receptacles. The green grounding plug extending from the adapter
must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a
three-slot grounded receptacle is available.
3. Occasionally a new heater will emit a slight “new smell” odor
during initial use. This smell should dissipate within the first
hour of use.
4. Always unplug heater when not in use. When heaters are
not to be used for an extended period of time, cord should
be coiled and tied to prevent damage and heater should be
stored in a safe location.
Figure 1
MAINTENANCE INSTRUCTIONS
1. If heater fails to operate or if heater or power cord becomes
damaged, unplug and discontinue use. DO NOT attempt to
repair the heater. There are no user-serviceable parts
inside.
2. If the heater fails during the warranty period, return to place
of purchase or to the factory as outlined in the LIMITED
WARRANTY statement below.
3. Heater may be cleaned using a damp cloth or sponge and a
mild detergent. Never submerge or soak heater in water.
Always turn heater off and unplug before cleaning. Heaters
may be repainted if desired. Use only high temperature
water based acrylic paints.
All products manufactured by Marley Engineered Products are warranted against defects in workmanship and materials for one year from date of installation, except
LIMITED WARRANTY
heating elements which are warranted against defects in workmanship and materials for five years from date of installation. This warranty does not apply to damage from
accident, misuse, or alteration; nor where the connected voltage is more than 5% above the nameplate voltage; nor to equipment improperly installed or wired or
maintained in violation of the product’s installation instructions. All claims for warranty work must be accompanied by proof of the date of installation.
The customer shall be responsible for all costs incurred in the removal or reinstallation of products, including labor costs, and shipping costs incurred to return products
to Marley Engineered Products Service Center. Within the limitations of this warranty, inoperative units should be returned to the nearest Marley authorized service center or the Marley Engineered Products Service Center, and we will repair or replace, at our option, at no charge to you with return freight paid by Marley. It is agreed that
such repair or replacement is the exclusive remedy available from Marley Engineered Products.
THE ABOVE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE AFORESAID EXPRESSED WARRANTIES ARE HEREBY DISCLAIMED AND EXCLUDED FROM
THIS AGREEMENT. MARLEY ENGINEERED PRODUCTS SHALL NOT BE LIABLE FOR CONSEQUENTIAL DAMAGES ARISING WITH RESPECT TO THE
PRODUCT, WHETHER BASED UPON NEGLIGENCE, TORT, STRICT LIABILITY, OR CONTRACT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state.
For the address of your nearest authorized service center, contact Marley Engineered Products in Bennettsville, SC, at 1-800-642-4328. Merchandise returned to the factory must be accompanied by a return authorization and service identification tag, both available from Marley Engineered Products. When requesting return authorization,
include all catalog numbers shown on the products.
HOW TO OBTAIN WARRANTY SERVICE AND
WARRANTY PARTS PLUS GENERAL INFORMATION
1. Warranty Service or Parts
2. Purchase Replacement Parts
3. General Product Information
Note:
When obtaining service always have the following:
1. Model number of the product
2. Date of manufacture
3. Part number or description
1-800-642-4328
1-800-654-3545
www.marleymep.com
470 Beauty Spot Rd. East
Bennettsville, SC 29512 USA
Part No. 5200-2184-005
ECR 38730
01/11
2
Loading...