QFX TV-LED1911 Instruction Manual
19” Full Color LED TV
MODEL NO.: TV-LED1911
INSTRUCTION MANUAL
BEFORE USING THIS PRODUCT, READ, UNDERSTAND
AND FOLLOW THESE INSTRUCTIONS.
Save this booklet for future reference.
1
SAFETY INSTRUCTIONS
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
SERIOUS PERSONAL INJURY:
● This product shall not be exposed to dripping or splashing and that no objects filled
with liquids, such as vases, shall be placed on the apparatus.
● Situate this product away from heat sources such as radiators, heat registers,
stoves, or other appliances (including amplifiers) that produce heat.
● Clean the product only as recommended by the manufacturer (see “Maintenance”)
section for details). Unplug the power cord from the wall outlet before cleaning,
● Unplug the power cord from the wall outlet when left unused for an extended
period.
● Prevent objects/liquids from falling or spilled on the product.
● Operate the product only with the supplied power adapter. Route power cords so
they are not likely to be walked on or pinched by items placed upon or against them,
paying particular attention to plugs, convenience receptacles, and the point where they
exit from the product.
● Where the MAINS plug or an appliance coupler is used as the disconnect device,
the disconnect device shall remain readily operable.
● Do not operate this product under the following conditions.
- When the power-supply cord or plug is damaged.
- If liquid has been spilled into or objects have fallen into the product.
- If the product has been exposed to rain or water.
- If the product does not operate when used according to the operating instructions.
- If the product has been dropped or damaged in any way.
● Do not attempt to service the product; take it to the electronics repair shop of your
choice for any servicing or repair.
● Do not overload wall outlets, extension cords, or integral convenience receptacles.
IMPORTANT INSTRUCTIONS
2
CAUTION- TO REDUCE THE RISK OR PERSONAL INJURY OR
PRODUCT/PROPERTY DAMAGE:
● This product is intended solely for non-commercial, non-industrial, personal use as a
portable television. Do not use this product for any other purpose.
● Do not subject the product to violent shocks, extreme temperatures, or lengthy periods
or direct sunlight.
● Keep the product away from magnetic objects, motors, and transformers.
● Do not use outdoors in inclement weather.
● Do not use the TV while driving; this is dangerous and is illegal in some areas.
BATTERY HANDLING AND USAGE:
● KEEP BATTERIES AWAY FROM CHILDREN AND PENTS. ONLY ADULTS
SHOULD HANDLE BATTERIES.
● NEVER THROW BATTERIES INTO A FIRE OR EXPOSE THEM TO FIRE OR OTHER
HEAT SOURCES.
● FOLLOW THE BATTERY MANUFATURES’S SATIETY AND USAGE INSTRUCTIONS.
3
All the pictures in this instruction manual are just for your reference, specification
should refer to actual accessories.
ACCESSORIES
Instruction
manual
………………….....1
Remote control with
battery ……………..1
Car cord
…………
1
Desktop AC adaptor
and power cord
………
…………
……
1
4
TABLE OF CONTENTS
GETTING STARTED
IMPORTANT INSTRUCTIONS...................................................................................1-2
ACCESSORIES……….......................................................................................................3
FEATURES....................................................................................................................5
GENERAL PARTS.................................................................................................................6
REMOTE CONTROL..........................................................................................................7-8
REMOTE CONTROL PREPARATION...................................................................................9
BASIC CONNECTION....................................................................................................10-12
OPERATIONS
BASIC OPERATIONS.............................................................................................13-17
MAIN MENU...........................................................................................................18-28
TV MODE....................................................................................................................18-27
PC MODE………........................................................................................................27-28
FOR REFERENCE
MAINTENANCE...........................................................................................................29
SPECIFICATIONS...............................................................................................................29
TROUBLESHOOTING.........................................................................................................30
5
19" TFT DISPLAY
This player has a built-in 19” TFT display window to provide clear vision and low
radiation.
SUPPORT AUTO TV SCANNING
SUPPORT DIGITAL BROADCASTING RECEPTION
SUPPORT ELECTRONIC PROGRAM GUIDE
SUPPORT USB MULTIMEDIA PLAYBACK
SUPPORT MULTI-LANGUAGES ON SCREEN DISPLAY
SUPPORT FULL FUNCTION REMOTE CONTROL
SUPPORT PC AUDIO, ANT, VGA, VIDEO, AUDIO R/L, HDMI AND YPBPR INPUT
WITH HEADPHONES AND COAXIAL OUTPUT JACK
WITH EXTERNAL ANTENNA JACK
WITH BUILT-IN SPEAKERS
WITH WEAK SIGNAL ENHANCEMENT FUNCTION
WITH NOISE REDUCTION FUNCTION
FEATURES
6
MAIN UNIT
1. TFT display screen
2. Remote control sensor
3. Power indicator- In standby mode the
indicator light will display red color; when
switching on the unit the indicator light will
display blue color.
4. Stand holder
5. SOURCE button- To select the input source.
6. MENU button- To enter menu setting page.
7. CH- button- To select previous channel or
move down.
8. CH+ button- To select next channel or move
up.
9. VOL- button- To decrease the volume level
or move left.
10. VOL+ button- To increase the volume level
or move right.
11. POWER button- To switch ON/OFF the TV.
12. USB slot- For software updating and
music/photo playback.
13. Y Pb Pr input jack
14. COAX OUT jack
15. HEADPHONE output jack
16. PC AUDIO input jack
17. ANT input jack- To connect the antenna.
18. VGA input jack
19. VIDEO input jack
20. AUDIO L/R- To connect the audio output
jack of DVD or VCR.
21. HDMI input jack
22. POWER input
GENERAL PARTS
7
REMOTE CONTROL
1. POWER: To set the unit in standby mode;
press it again to switch it on.
2. NUMBERIC BUTTONS (0-9): To input the
number information, such as channel number and
so on.
3. -/--: To select additional channels (digital) being
broadcast by the same station. For example, to
select channel “15-3”, press “1” and “5”, then
press “-/--” and “3”.
4. GREEN button
5. RED button
6. VOL +/-: Press VOL+ button to increase the
volume, or press VOL- button to decrease the
volume.
7. EPG: To display electronic program guide
information.
8. PICTURE: To switch the picture mode.
9. CC: To set CC function On or Off in TV mode.
10. Navigation buttons: Press ▲/▼/◄/►
buttons to move up/down/left/right.
11. MENU: To display the main menu. Press it
again to return to previous menu page.
12. SLEEP: To select desired Sleep Timer.
13. MTS/AUDIO: To select desired soundtrack in
TV mode.
14. F.LIST: To display the favorite channels list
page in TV mode.
15. C.LIST: To display available channels list page in TV mode.
8
16. MUTE: To mute the sound.
17. : To return to previous channel or input
source.
18. YELLOW button
19. BLUE button
20. CH+/-: Press CH+ button to play next channel,
or press CH- button to play previous channel.
21. INFO: To display current program information.
22. SOURCE: To switch the input source.
23. SOUND: To switch the sound mode in TV
mode.
24. ENTER: To confirm a selection.
25. EXIT: To exit menu page.
26. AUTO: To adjust the screen automatically (in
PC mode).
27. ASPECT: To select desired displaying mode.
28. FREEZE: To hold the picture during normal
playing.
29. FAV: To label current program as a favorite
one or not.
9
REMOTE CONTROL PREPARATION
BATTERY INSTALLATION
Install the batteries as the following pictures. Be sure + and – terminals are positioned as
indicated in the battery compartment (Fig1).
SERVICE LIFE OF BATTERIES
- The batteries normally last for one year although this depends on how often the remote
control is used.
- If the remote control fails to work even when it is operated near the player, replace the
batteries.
- Use two size AAA dry batteries.
NOTE:
● Do not drop, step on or otherwise impact the remote control. This may damage the
parts or lead to malfunction.
● If the remote control is not going to be used for a long time, remove the batteries.
REMOTE CONTROL
OPERATION
Point the remote control from no more
than about 6m from the remote control
sensor and within about 60°of the
front of the player(Fig2).
NOTES:
- The operating distance may vary
according to the brightness of the
room.
- Do not point bright light at remote
control sensor.
- Do not place objects between the
Remote control and the remote control
sensor.
- Do not use this remote control while
simultaneously operating the remote
control of any other equipments.
Fig1 Fig2
Push
Open
Press
Remote Control
Sensor
10
● Ensure all the cables are disconnected from the main unit before connecting to AC
power source by AC power adaptor.
● Read through the instructions before connecting other equipments.
CONNECTING TO AC POWER SOURCE
CONNECT EXTERNAL ANTENNA TO UNIT
Install external antenna into antenna jack for best picture.
BASIC CONNECTION
Main unit
To DC 12V jack
AC adaptor
To power outlet
Outdoor
antenna
amplifier
Indoor
antenna
amplifier
Power plug
of antenna
amplifier
75 OHM
antenna
plug
Antenna
11
PC/VGA CONNECTION
COMPOSITE AV CONNECTION
COAXIAL OUT CONNECTION
Back of DVD/VCR
Headphones
(Optional)
AV cable
(Optional)
Back of PC
VGA cable
(Optional)
Audio cable
(Optional)
Use VGA cable and Audio
cable to connect the unit
with TV or PC, and use this
product as a monitor.
Use coaxial cable to connect the unit with amplifier or other audio
decoding devices for coaxial audio signal output.
12
HDMI CONNECTION
YPbPr CONNECTION
CONNECTING TO USB MEMORY DEVICE
Back of DVD/VCR
HDMI cable
(Optional)
Use HDMI cable to connect the
unit with other devices to receive
high-definition multimedia signal.
F
or software updating
and music/photo
p
layback
.
Back of DVD/VCR
YPbPr cable
(Optional)
13
MAKE SURE ALL THE EQUIPMENTS AND AC ADAPTOR ARE
CONNECTED PROPERLY AND THE UNIT IS SET IN CORRECT MODE
BEFORE KINDS OF OPERATIONS.
- Press POWER button on the top of this unit to POWER ON the unit (indicator light
displays in blue), press it again to POWER OFF the unit (indicator light displays in
red). Or press POWER button on remote control to POWER ON the unit (indicator
light displays in blue), press it again to STANDBY mode (indicator light displays in
red).
- Press SOURCE button on unit top or remote control to set the unit in TV mode.
SELECT WANTED PROGRAM
1. Press CH+ button to play next channel.
2. Press CH- button to play previous channel.
3. Press numeric buttons on the remote control directly to select wanted program.
Example : Track 9, press ＂9＂, three seconds later it will turn to track 9 automatically, or
press ENTER button to confirm directly.
Track 12, press ＂1＂ and ＂2＂, three seconds later it will turn to track 12 automatically,
or press ENTER button to confirm directly.
NOTE : If one frequency dot has more than one channel, for example, track 15-3,
press ＂1＂ and ＂5＂, then press ＂-/--＂ and ＂3＂, three seconds later it will turn to
track 15-3 automatically, or press ENTER button to confirm directly.
VOLUME CONTROL
- Press VOL+ or VOL- to adjust the level of current volume.
Available range: 0-100.
MUTE CONTROL
- Press MUTE button to mute the sound, press it again to turn on the sound.
SOURCE SETTING
- Press SOURCE button on remote control to display the sources list.
- Press UP or DOWN navigation button to select desired input source, then press ENTER
button to confirm selection.
- Or press SOURCE button on unit top repeatedly to select desired input source.
Available options: TV, AV, YPbPr, HDMI, PC, Media.
BASIC OPERATIONS
14
PICTURE MODE
- Press PICTURE button on remote control repeatedly to select desired picture mode.
Available options: User, Dynamic, Standard, Movie.
SOUND MODE
- Press SOUND button on remote control repeatedly to select desired sound mode.
Available options: User, Dynamic, Standard, Soft.
CLOSED CAPTION
- Press CC button on remote control repeatedly to set the CLOSED CAPTION function On
or Off.
SLEEP TIME SETTING
- Press SLEEP button on remote control repeatedly to select desired sleep time.
Available options: Off, 15min, 30min, 60min, 90min, 120min.
VIDEO SIZE SETTING
- Press ASPECT button on remote control repeatedly to select desired video size
Available options: Normal, Wide, Cinema, Zoom.
MTS/AUDIO SETTING
- Press MTS/AUDIO button on remote control to enter Sound menu page, then use UP or
DOWN navigation button to select desired option. Options: Mono, Stereo, SAP.
(Not available in all channels)
- Or press MTS/AUDIO button on remote control to display Digital Sound language.
(Not available in all channels)
INFORMATION DISPLAY
- Press INFO button on remote control to display information of current program.
EPG(ELECTRONIC PROGRAM GUIDE)
- Press EPG button on remote control to enter into Electronic Program Guide menu page.
(Not available in all channels)
- Press LEFT or RIGHT navigation button to view previous or next page.
15
FAVOURITE LIST
- Press F.LIST button on remote control to enter FAVORITE LIST menu page.
- Press navigation buttons to select desired channel.
- Press ENTER button to confirm selection.
NOTE: During normal playing, press FAV button on remote control to label current program
as a favorite one or not.
CHANNEL LIST
- Press C.LIST button on remote control to enter CHANNEL LIST menu page.
- Press navigation buttons to select desired channel.
- Press ENTER button to confirm selection.
FREEZE FUNCTION
- During normal playing, press FREEZE button on remote control to hold the picture, and
press it again to resume normal playing.
MUSIC PLAYBACK
- Before following operations, insert a USB memory device first.
- Press SOURCE button on unit top or remote control to set the unit in Media mode.
16
1. Press LEFT or RIGHT navigation button to select Music item.
2. Press ENTER button to enter it, then use navigation buttons to select the music file that
want to play.
3. Use navigation buttons to select which song to play, then repeat the second step to play
desired song.
4. Press EXIT button to return to previous menu.
PHOTO PLAYBACK
1. Press LEFT or RIGHT navigation button to select Photo item.
2. Press ENTER button to enter it, then use navigation buttons to select the photo file that
want to play.
3. Press ENTER button and below icon will appear on the screen.
3.1 Open
- Select this item, then press ENTER button to open selected file.
- Press navigation buttons to select which photo to play.
- Press ENTER button to play the selected photo, then press UP/DOWN navigation buttons
to rotate the photo clockwise/counterclockwise 90, 180, 270 degrees; press LEFT/RIGHT
navigation buttons to play previous/next photo.
- Press ENTER button to view the photo in full screen.
- Press navigation buttons to move up/down/left/right.
3.2 Thumbnail
- Select this item, then press ENTER button to play all the photos in thumbnail mode.
- Press UP or DOWN navigation button to view previous or next page.
- Press ENTER button, and a yellow frame will appear on the first photo, then press
navigation buttons to select which photo to play.
3.3 Slideshow
- Select this item, then press ENTER button to play the photos in slide show mode.
Media Setting
- Press LEFT or RIGHT navigation button to select Media Setting item.
1. Slideshow Interval
Available options: 1s, 5s, 10s.
17
2. Slideshow Effect
Available options: Off, Wipe Right, Wipe Left, Wipe Up, Wipe Down, Comb Side, Comb
UpDown, Checker, Mosaic, Fade, Blind Right, Blind Left, Blind Up, Blind Down, Box In, Box
Out, Slide in Right, Slide in Left, Slide in Up, Slide in Down.
3. Slideshow Repeat
Available options: On, Off.
4. Music Play Mode
Available options: Once, Play All, Random.
5. Music Play Repeat
Available options: On, Off.
6. Music Auto Play
Available options: On, Off.
NowPlaying
- Press LEFT or RIGHT navigation button to select NowPlaying item.
- Press ENTER button to enter below menu page.
- Press LEFT or RIGHT navigation button to select wanted option.
18
● The unit contains different setting menus. Once the initial programming is entered, it will
be remain in the memory until change, and the unit can always be operated under the same
conditions.
● The settings will be remained in the memory until the settings are changed, even after
setting the player to standby mode.
Common procedure for initial settings
- Press MENU button on unit top or remote control to display the main menu.
- Press LEFT or RIGHT navigation button to select wanted item.
- Press ENTER or RIGHT navigation button to enter submenu page.
- Press UP or DOWN navigation button to select the option that want to adjust.
- Press LEFT or RIGHT navigation button to adjust selected option to desired value. Then
press ENTER button to confirm the selection.
- Press MENU button to return to previous menu page.
- Press EXIT button to exit menu page.
TV MODE
- Press SOURCE button on unit top or remote control to set the unit in TV mode. Then the
screen will display below menu page, if first time using:
● Menu Language
- Press UP or DOWN navigation button to select Menu Language item.
- Press LEFT or RIGHT navigation button to select wanted language.
● Signal Type
- Press UP or DOWN navigation button to select Signal Type item.
- Press LEFT or RIGHT navigation button to select wanted Signal Type.
● Auto Channel Search
- Press UP or DOWN navigation button to select Auto Channel Search item.
- Press ENTER button to start channel searching.
MAIN MENU
19
1. PICTURE
1.1 Picture Settings
1.11 Picture Mode
Available options: User, Dynamic, Standard, Movie.
1.12 Brightness
The value of Brightness can be adjusted from 0-100.
1.13 Contrast
The value of Contrast can be adjusted from 0-100.
1.14 Color
The value of Color can be adjusted from 0-100.
1.15 Tint
The value of Tint can be adjusted from -50 to 50.
(Only available for certain TV system)
1.16 Sharpness
The value of Sharpness can be adjusted from 0-100.
NOTE: If the value of Brightness, Contrast, Color, Tint, and Sharpness is adjustable only
when the Picture Mode is set as User.
1.2 Screen Size
Available options: Normal, Wide, Cinema, Zoom.
1.3 PC Settings
NOTE: This item is available only in PC mode.
1.4 Color Temperature
Available options: Normal, Warm, Cool.
Loading...