QFX SB-2032BT User Manual

SOUND BAR WITH BLUETOOTH RECEIVER

MODEL NO.: SB-2032BT

1

CONTENTS

Safety information-------------------------------------------------------------------------------------------------2,3

Welcome ---------------------------------------------------------------------------------------------------------------4

Set up--------------------------------------------------------------------------------------------------------------------5

Your 2.0 Speaker Bar-------------------------------------------------------------------------------------------------6

Remote Control--------------------------------------------------------------------------------------------------------7

USB,Bluetooth---------------------------------------------------------------------------------------------------------8

FM Radio----------------------------------------------------------------------------------------------------------------9

Clock and Sleep Timer / Alarm------------------------------------------------------------------------------------10

-----------------------------------------------------------------11

---------------------------------------------------------------------- 12,13

Troubleshooting / Maintenance / T echnical specifications------------------------------------------------- 14

Operating and connecting an external device

Mounting the Speaker Bar onto a wall

14

1.Do not use harsh or abrasive cleaning agents or solvents.

2.Do not attempt to disassemble your product.

3.Do not paint your product.

4.Do not drop, throw or try to bend your product.

5.Do not expose your product to open flames.

Maintenance

Troubleshooting

Check that it is NOT set to mute.

Problem

No power

No sound
from bluetooth
first connection

Function
disturbed

The remote
control won' t
work

No sound

What to do

Check that the power is switched on at the wall.
Check if the power cord is properly connected to the power outlet.
Check that the volume control is NOT at minimum setting.

Check if you have entered password or not. It needs to start with
password 0000"".

If none of the above solutions work ,then switch off and
unplug your Speaker system ,leaving it for 2 minutes and
then switching it back on again.

Inspect or replace the battery.
Make sure there are no obstacles obscuring the front of the

Speaker.

Technical specifications

Size
Output power
Standby power consumption
Input sensitivity
S/N(A weight)
Frequency Response
L/ R seperation (1khz)
L/ R balance (stereo)
Supported file formats

20W+20W

810(L)x113.5(H)x61(D)mm

1W

800mV

60dB

50Hz~20KHz

40dB

1.5dB

MP3.WMA

*Specifications are subject to change without prior notice.

FM

87.5-108MHz

2

SAFETY INFORMATION

IMPORTANT SAFETY INSTRUCTIONS - READ CAREFULLY BEFORE USE.

!!

Keep these instructions

Do not use this unit near water.
Clean only with as lightly damp cloth.
Do not block any ventilation openings.
Install in accordance with the supplied instruction manual.
Protect the power cord from being walked on or pinched, particularly at plugs,

and the point where it exits from the unit.

Do not allow the power cord to overhang the edge of a table.
Unplug this unit when unused for long periods of time.

This symbol indicates that there are important operating maintenance
instructions in the literature accompanying this unit.

This symbol indicates that dangerous voltage constituting a risk
of electric shock is present within this unit.

WARNING! TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. THE UNIT
MUST NOT BE EXPOSED TO DRIPPING AND SPLASHING AND NO
OBJECTS FILLED WITH LIQUIDS SHOULD BE PLACED ON TOP OF IT.

!!

NOTE: No naked flames such as candles should be placed near or
underneath the unit.

IMPORTANT SAFETY INSTRUCTION(Continued)

This unit has been produced according to all current safety regulations.
The following safety tips should safeguard users against careless use and the
dangers connected with such use.

Although this appliance has been carefully manufactured and rigorously
checked priorleavingthefactory, as with all electrical appliancesitis
possible forproblemstodevelop. Ifyou notice smoke, anexcessive build up
of heat or any other unexpected phenomena, youshould disconnect the
plug from the mains powersocket immediately.
Ensure that the unit is sufficientlyventilated! Never place next to or

underneath curtains!

You should use

2 pieces of short screws 2 pcs plastic tubes

2/. Mounting on the dry wall

1. Use the TAPE MEASURE to decide how high you'd like to hang the Speaker Bar
on the wall. The SOUND Bar must be hung within 5 feet of an AC power outlet
for the attached AC power cord to reach.

2. Mark the position of the mounting screws on the wall using a pencil.

3. Line the LEVEL up on both of your mark sure they are level.
If they're not, adjust the marks as needed to make them level.

4. Drill a hole by a powerful electric drill.

5. Use a hammer gently nail 2 plastic tubs into the holes.

6. Drill through the screws directly into the holes.

7. Use the LEVEL to check that the mounting screws are level.

8. Put the SOUND Bar onto the mounting brackets, and make sure there is a firm
and stable connection before letting go of the Sound Bar.

9. Finally, use the LEVEL to confirm that the Sound Bar is level.

(1)

(2)

13

The mains plug or appliance coupler is used as the disconnect device,

the disconnect device shall remain readily operable.

This set should only be connected to a mains power supply which matches

that stated on the label on the rear of it-do not attempt to connect it to any
other type of supply.

The socket-outlet must be installed near the equipment and easily accessible.

'

Toprevent overload, dont share the same mains supply socket with too

many other items of equipment.

Apparatus with Class 1 construction shall be connected to a mains socket

outlet with a protective earthing connection.

Keep away from rodents. Rodents enjoy biting into electric flexes.

Always hold the plug when pulling out the plug from the mains supply socket.
Do not pull on the flex, the flex can become overloaded and cause a short
circuit.

Set up the unit so that no one is able to trip over the flex.

Do not place heavy items on the flex, which may damage it.

Take note that the flex cannot be reached and pulled by young children,
avoiding injury.

Do not set up the unit near to heat sources. The casing and the flex could be
damaged by the impact of heat.

Avoid placing the unit on any surfaces that may be subject to vibrations or
shocks.

When you leave your home for long periods of time, unplug the AC power
cable for safety reasons.

The unit becomes warm when in operation. Do not place any covers or
blankets on the unit in order to prevent overheating. The ventilation holes
are not to be blocked. Do not set up near radiators. Do not place in direct
sunshine. When placing on a shelf leave 5cm(2 )free space around the
whole unit.

Do not allow water or moisture to enter the unit. Do NOT use in wet or moist
areas such as Bathrooms, steamy kitchens or near swimming pools.

Do not use this unit when moisture condensation may occur.

Any repairs must be carried out by qualified personnel only.

Liquids spilt into the unit can cause serious damage. Switch the set OFF and
disconnect the mains power supply, then consult a qualified service person
before attempting to use the unit again.

Do NOT remove the safety covers. There are no useable or serviceable parts
inside. You may invalidate the warranty. Qualified personnel must only service
this apperatus.

Take good care of the remote control, do not drop.

Never place hot objects or open flame sources on or close to the unit.

High temperatures can melt plastic and lead to fires.

To clean use a soft dry cloth. Do NOT use solvents or petrol based fluids.
For stubborn stains, you may use a damp cloth with dilute detergent.

3

12

We recommend having this speaker professionally mounted. By using the included wall
mounting accessories, the sound bar can be mounted onto a wall.

Mounting the Speaker Bar onto a wall

You will need

Level
Manual or Electric drill

Distance Between Two Brackets

1/. Mounting on the wooden wall

You should use

600mm

Pencil
Tape Measure

1. Use the TAPE MEASURE to decide how high you'd
like to hang the SOUND Bar on the
wall. The SOUND Bar must be hung within 5 feet of
an AC power outlet for the attached AC power cord
to reach.

2. Mark the position of the mounting screws on the wall
using a pencil.

3. Line the LEVEL up on both of your mark sure they are
level. If they're not, adjust the marks as needed to
make them level.

4. After you've double checked your marks, drill through the screws directly
into the marks that you have made on the wall.

5. Use the LEVEL to check that the mounting screws are level.

6. Put the Sound Bar onto the mounting brackets, and make sure there is a firm and
stable connection before letting go of the Sound Bar.

7. Finally, use the LEVEL to confirm that the Sound Bar is level.

2 pcs short screws

4

2-3 inches

Welcome

Congratulations on purchasing this bluetooth sound bar. The Speaker Bar
allows you to play TV audio content from an attached television, and from
your bluetooth enabled mobile phone, PC or Tablet.
Please read the warning section carefully before using your Speaker Bar.

You should have

Ventilation
When placing the Speaker Bar on an entertainment center,
bookshelf,or any type of enclosed space, be sure to allow at
least 2-3 inches of space around the Speaker Bar for
ventilation. If the Speaker Bar is enclosed in a tight space,
without ventilation, heat generated from the Speaker Bar
could produce a potential heat hazard.

Note:

11

Make sure you match up the Red (R)and White (L)Audio connectors,either RCA cable or
line in/out cable only.

Operating and connecting an external device

You can also connect an external device to your Speaker Bar through the AUX/LINE in
jack in the rear panel of the sound bar To play the external device you will need to select
AUX SOURCE using the SOURCE button.

Once the device is connected you can control playback as you would usually.

Press the VOLUME + and - buttons on the sound bar to increase or reduce the volume.
Press the MUTE button to turn the sound off, press it again to return to the previous
volume level.

You can connect external devices (MP3 player ,CD player ,TV etc) to the Speaker Bar in
several ways.

Using a RCA audio cable

Using a 3.5mm line-in cable

1

TV

Audio output

Left(white)

Right(red)

MEMUMEMU

Headphone

BLUETOOTH

2

2.0CH Speaker Bar

RCA CABLE 1
LINE in Cable 1
AC/DC adapter 1

2

1

3

Remote control

Wall mount fittings
screw 2pcs

plastic tubes x 2pcs

VOL+

STANDBY

3D

SOURCE

MUTE

EQ

SLEEP

ALARMCLOCK

MEMUPREPEAT

DOWN

VOL

5

Setting up your Speaker Bar

Insert the AC adapter plug into a appropriate wall socket
and turn on power to the out let.

The remote control battery

1. It includes one piece of 2025 battery.

2. Remove the transparent sheet.

3. Replace the remote control battery when it no longer operates or
the range is reduced considerably .

Set up

VOL+

STANDBY

3D

SOURCE

MUTE

EQ

SLEEP

ALARMCLOCK

MEM

UP

REPEAT

DOWN

VOL

10

Clock and Sleep Timer

Setting the Sleep Timer

1. Press the STANDBY button to turn the power on.

2. Press the SLEEP button repeatedly to set the sleep timer.

3. After the set sleep time has expired, the sound bar will automatically power off.

Setting the Clock

1. Press the STANDBY button to turn the power off.

2. Press the CLOCK button on the remote control.

3. The time on the display will begin blinking.

4. Press the and buttons on the remote control to adjust the hour.

5. Press the CLOCK button again on the remote control to go to minute adjustment.

6. Press the and buttons on the remote control to adjust the minute.

7. Press CLOCK button again to confirm the setting.

Alarm

Setting the Alarm

1. Press the STANDBY button to turn the power on.

2. Press SOURCE button twice on the remote control and select the FM Mode.
Press or buttons to select the desired radio frequency .

3. Adjust the volume to the desired level .

4. Press the STANDBY button on the remote control to switch off the power.

5. Press the ALARM button on the remote control.

6. The time on the display will begin blinking.

7. Press the and
8

11.After the set time has expired the ALARM will ring the preset radio station.

buttons on the remote control to adjust the hour.

. Press the ALARM button again on the remote control to go to minute adjustment.

9. Press the and buttons on the remote control to adjust the minute.

10. Press ALARM button again to confirm the setting.

Your 2.0 Speaker Bar

Features Defined

10

6

STANDBY

PLAY

MODE VOL+VOL

1
2

3
4

5

7

8
9

AUX IN

DC 18V

FM

11 12 13

1. LCD display

2. STANDBY button : Press to turn the speaker bar off or on.

3. USB jack : To insert memory sticker

4. PLAY button : Press to play music.

5. MODE button : Press to select the input source.Each press
will source through the following selection AUX-FM-BT-USB.

6. REMOTE SENSOR : Ensure this area is not covered or blocked
by any object.

7. Bluetooth LED indicator : It is lighting when BT mode is selected.

8. VOL + : Press to increase the volume.

9. VOL - : Press to reduce the volume

10. Mounting bracket.

11.

12. AUX/LINE in jack : To insert either RCA cable or LINE in cable

13. DC jack in.

FM antenna port.

FM Radio

Adjust the FM Wire Antenna (included) to get the best reception signal.

1. Press the STANDBY button to turn the bar speaker on.

2. Press the SOURCE button to switch to FM radio mode.

3. Press the or buttons on the remote to tune the FM radio.

Listening to a Saved Radio Station

1. Press the STANDBY button to turn the bar speaker on.

2. Press the SOURCE button to switch to FM radio mode.

3. Press the MEM buttons on the remote to cycle through saved radio stations.

Saving a Radio Station

1. Follow the instructions for tuning the FM radio.

2. After tuning to the desired station, press the MEM button.

3. Press the UP or DOWN buttons on the remote to select a preset.

4. Press the MEM button to save the current radio station to the selected preset.
Up to 20 stations can be saved to the bar speaker s memory.

FM Antenna

Tuning the FM Radio

69

10

USB

7

8

1. Playing the files form the connected USB device. Connect a USB flash or other USB
storage device (up to 16GB) to the USB jack or insert desired media (up to 16GB)
Memory stick with adaptor/SD and MMC card). You can play music in MP3 format.

2. Press the STANDBY button.

3. Press the SOURCE button on the remote control or on the unit to select USB function.
NOTE : The time taken for thecontents of the desired media to be read varies
according to the memory size.

4. Play and Pause the desired song track using the navigation on the remote
control. Press go back to pervious . Press to jump to next track. Press
to repeat the track.

REPEAT

USB OPERATION

VOL+

STANDBY

3D

SOURCE

MUTE

EQ

SLEEP

ALARMCLOCK

MEM

UP

REPEAT

DOWN

VOL

1

4

7

10

13
14
16

2

3
5

6
8

9
11

12

15

17

Remote Control

1. STANDBY button: Press to turn the speaker bar off or on.

2. EQ button: Press to select FLAT, ROCK, JAZZ, POP and
CLASSIC.

3. MUTE button: Press to mute the volume.

4. CLOCK: Press to set the time.

5. ALARM: Press to set the alarm.

6. SLEEP: Press repeatedly to set the sleep timer.

7. MEM: Press to cycle through saved radio stations

8. UP: Press to navigate up radio stations.

9. REPEAT: Press to repeat a single or all track.

10. : Press to go to previous track.

11. : Press to play or pause music.

12. : Press to go to next track.

13. SOURCE: Press to select the input source.Each press will
source through the following selection AUX-FM-BT-USB.

14. DOWN: Press to navigate down radio stations.

15. 3D: Press to switch on or off 3D effect.

16. VOL-: Press to reduce the volume.

17. VOL +: Press to increase the volume.

1. Switch on the sound bar. Press the SOURCE button and select BT function.

2. The BT blue LED will flash 3 seconds and then stop for 30 seconds. It is now searching
for the last paired device.

3. If there is no device searched, blue LED will flash again. At this time, you can pair with
other new device you prefer. Turn on a device such as an iPod, iPhone, Tablets or
Mobiles etc with bluetooth transmitters. When a device is connected and paired with
the sound bar , it will show the name of SB-2032BT . Enter password 0000 to
connect or pair with.

4. If the initial set up connection is succesful ,the next time the speaker is turned on , the
speaker will automatically pair to the last device it was connected with .

5. If there is no bluetooth transmitter device found, the BT blue LED will continue to flash
non stop.Press SOURCE button on remote control to select USB,AUX or FM.

"" ""

Bluetooth SET UP

NOTE:

1. The Bluetooth speaker only connects to device at a time. Turn off the Bluetooth
speaker in order to pair the device with another Bluetooth device.

2. The maximum transmission between the Bluetooth speaker and a device is 10 meters
or 32 feet.

3. Interferece may occur during playback when using the Bluetooth funtion near other
wireless devices. If playback through Bluetooth is problematic, move the Bluetooth
speaker and the playback device to a different location, or use the 3.5mm audio cable
jack instead of the Bluetooth function.

For an NFC-enabled Bluetooth product, you can achieve rapid pairing connectivity.
With an NFC-enabled device, please open the NFC function and touch NFC sensitive
region of the sound bar, you can quickly connect Bluetooth pairing;
In the connected state, use NFC- enabled device near the NFC sensitive area of sound
bar, you can disconnect Bluetooth.
In the off state, use device near NFC sensitive area of sound bar, you can connect
Bluetooth again.

NFC OPERA

TION