QFX 3011BT User manual

www.qfxusa.com

PBX-3011BT
120V-240V
80W RMS

User Manual for PBX-3011BT Portable Speaker

WARNING!

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER ON
THIS SPEAKER.
THERE ARE NO USER-SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO A QUALIFIED
TECHNICIAN.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user
to the presence of dangerous voltage within the product's enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to humans.Users should exhibit extra safety when this
symbol appears in this instruction manual and follow all precautions as they are stated.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in this manual.

1- Read these instructions.
2- Keep these instructions.
3- Heed all warnings.
4- Follow all instructions.
5- WARNING: To prevent fire or electric shock, do not expose this equipment to rain or moisture.
Do not store or operate this product near any liquids.
6- Clean only with a dry cloth.
7- Do not store or operate this product near any heat sources such as radiators, heat registers,
stoves, or other apparatuses (including amplifiers) that produce heat. Keep this product in a well
ventilated area.
8- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding plug has two blades and a round grounding
prong. The wide blade or third prong is provided for your safety. If the provided plug does not fit your
outlet, consult an electrician for the replacement of the ob solete outlet.
9- Protect all the wires connected to this unit from being walked on or pinched, particularly plugs
and the point where they exit from the unit. When removing the cord from the poweroutlet, remove
it by holding the plug, not by pulling the cord.
10- Unplug the unit during lightning storms or when unused for long periods of time.
11- When wiring this unit and all other equipment used in connection to this unit make sure that all
of your equipment is turned OFF.
12- Once installation and wiring is complete power on all your equipment with the volume and level
controls turned DOWN. Once all the equipment in ON slowly raise the volume or level controls to
their proper positions.
13- Before Placing, Installing, rigging, or suspending any product, inspect all hardware, suspension,
cabinets, transducers, brackets and associate equipment for damage. Any missing, corroded,
deformed, or non-load rated component could significantly reduce the strength of the installation,
placement or array. Any such condition severely reduces the safety of the installation and should
be immediately corrected. Use only hardware which is rated for the loading conditions of the
installation and any possible short-term, unexpected overloading, Never exceed the rating of the
hardware or equipment.
14- Consult a licensed, Professional Engineer regarding physical equipment installation,Ensure
that all local, state and national regulations regarding the safety and operation of equipment are
understood and adhered to.
15- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.

Introduction

Congratulations and thank you for your purchase of this QFX Powered Portable PA System with
wired microphone, USB & SD Card ,Bluetooth inputs . To get the most from your system, we
recommend you review all the information provided in this instruction Manual.

BE SURE THAT YOU HAVE COMPLETELY CHARGED THE BATTERY PRIOR TO FIRST USE
TO MAXIMIZE THE BATTERY'S LIFESPAN.

-1-

PBX-3011BT REAR PANEL

PBX-3011BT

8

7

6

5

4

1

2

3

-2-

PBX-3011BT

PBX-3011BT REAR PANEL

1. Antenna is for receiving the FM signal. Before use, pull up the telescopic FM antenna. After
use,pack up the FM antenna to better protect it.

2. DC 12V IN is for connecting to 12V external battery if needed.

3. 12V FUSE: Provided battery is damaged or internal short circuit, the fuse will be burnt in order
to protect the machine & battery. The unit can work well after replace a n ew fuse.

4. Power Supply: The power switch should be set to the off posi ti on before the power supply is
connected.

5. Voltage Selector 120V-240V. Be sure the unit's voltag e in the outlet you are using.

6. Power Button: Press this button to power the unit on, off or to charge the unit. If the battery
needs to be charged, set the unit to AC and connect the power cable to the rear of the unit.
When set to AC, the unit can also be powered by an external power supply (electrical outlet) even
if the battery is dead. In this case you need to have the unit set to the voltage corresponding to
the voltage of the outlet. To turn the unit off set the power button to OFF. It is recommen de d to
fully charge the battery prior to using the unit for the first time. It is also recommended to charge
the battery at least every 2-3 months to keep the battery operating to it highest capacity.

7. AUX2 Input(1/8"): The 1/8” AUX Input is designed to connect directly to a mp3 player or any
other stereo level audio device. Please note that there are two AUX Inputs, RCA and 1/8”. If
both the RCA and 1/8”inputs are connected the unit is automatically play from the 1/8” AUX input.

8. AUX1 Input (RCA): The RCA Input is designed to connect directly to a CD/DVD/TV or any
other stereo level audio device.
Please note that there are two AUX Inputs, RCA and 1/8”. If both the RCA and 1/8”inputs are
connected the unit is automatically play from the 1/8” AUX input. To play from the RCA AUX
input, please disconnect the 1/8” connection from the 1/8” AUX Input.

-3-

PBX-3011BT

PBX-3011BT FRONT PANEL

5

1

3

6

4

2

21

20

19

18

16

17

111213141 5

1. Previous Folder Button: Press this button to move to the previous folder on USB flash drive or

SD card.

2. Previous Track Button: When on USB/SD mode, short press this button to move to the previous
track for USB/SD. Long press this button to reduce the volume for USB/SD.
When on FM mode, short press this button to move to the previous channel. Long press this button
to reduce the volume for FM.

3. Next Folder Button: Press this button to move to the next folder on USB flash drive or SD card.

4. Next Track Button: When on USB/SD mode, short press this button to move to the next track
for USB/SD. Long press this button to increase the volume for USB/SD.When on FM mode, short
press this button to move to the next channel. Long press this button to increase the volume for FM.

5. Repeat Button: Repeat button will only control the USB/SD card inputs. Press this button to
select the repeat mode for USB/SD.

6. Play/Pause Button: The play /pause button will only control the USB flash drive/SD card and
FM inputs.
When on the mode of USB/SD, Press this button to play or pause the track for USB/SD.
When on the mode of FM, press this button to auto scan all channels.

7. EQ Mode Button: Press this button to select between the 5 built-in EQ modes. This will only
work for USB flash drive or SD card inputs.

8. Input Mode Button: Press this button to toggle between the various inputs (AUX, USB, SD, FM, ).

9. Microphone Input(1/4"): Connect a microphone to this microphone input terminal.

10. Microphone Input(1/4"): Connect a microphone to this microphone input terminal.

11.Mode selector:Press the button down to enter the Bluetooth mode,press again to enter the
mode for (AUX, USB, SD, FM,).

12. Master Level Control: Turn this knob to adjust the master volume.

13. Treble adjustment: Turn this knob to increase the treble on the LINE/USB/SD/FM inputs

14. Bass adjustment: Turn this knob to increase the bass on the LINE/USB/SD/FM inputs

15. Microphone Echo Knob: Use this knob to adjust the echo for the microphone input (Mic1&
Mic2).

16. Microphone Volume Knob: Turn this knob to adjust the microphone volume level of the
microphone input (Mic1& Mic2)

17. Guitar Volume Control: Turn this knob to adjust the volume for the guitar.

18. Guitar Input (1/4"): Connect a guitar cable to this input terminal.

19. SD/MMC card slot: Connect your SD/MMC card memory storage (flash drive) device here.
The maximum size of the SD/MMC card can not exceed 16GB. The speaker will only play .mp3
& .wma files from the SD/MMC card input. Do not connect your computer to this input as it will
not play files directly from a computer.

20. Guitar Input (1/4"): Connect a guitar cable to this input terminal.

21.USB slot: Connect your USB memory storage (flash drive) device here. The maximum size
of the USB can not exceed 16GB. The speaker will only play .mp3 &.wma files from USB input.
Do not connect your computer to this input as it will not play files directly from a computer.

-4-

7

8

9

10

PBX-3011BT

PBX-3011BT DISPLAY MENU

1 2 3 4 5 6

7

When the unit is ON, connect the USB flash drive or SD Card to the unit.
Press and hold down the Input Mode button on the rear panel, the unit will go to the main menu.
Press next track button or previous track button to move left or right.
Press PLAY button to enter the menu.

"MSC" is the mode of USB flash and SD card.
"FM" is the model of FM radio.
"SYS" is the mode of system settings for the unit.
"AUX" is the mode of RCA input.

When playing the MP3,Press and hold down the Play button,the unit will go to the menu that shows
"Repeat,Music volume control,File browser and Exit.
When enter the Repeat menu,you can choose Repeat All,Repeat Folder,Repeat One or Ramdon.
When playing the MP3,Press pause, and then long press the play button.the unit will go to the
menu that shows "File browser,Delete file and Delete all"
Press next track button or previous track button to move up or down.
Press PLAY button to enter the menu.

PBX-3011BT DISPLAY USB/SD MODE

1. Input Mode: The input mode will display here. When a USB flash drive / SD Card is inserted
into the USB/SD input, the unit will automatically switch to USB/SD mode and begin playing .mp3
or .wma audio files from the USB flash drive / SD Card.

2. Elapsed Time: The elapsed time on the track currently playing from the USB flash drive / SD
Card will display here.

3. EQ Mode: All EQ modes will display here.

4. Repeat Mode: Repeat mode will display here. When the USB flash or SD card mode is selected,
press the REP button on the remote control to select the repeat mode of USB/SD.
When "A" appears on the display screen: All tracks on USB flash /SD card will be repeated.
When "D" appears on the display screen: All of the tracks from the folder currently being played
will be repeated.
When " 1" appears on the display screen: The track currently playing will be repeated.

5. Track Number / Total Tracks: The track number currently playin g from the USB/SD will display
on top. The total tracks on USB flash drive / SD Card will display on the bottom.

6. The Information of Track: Here display the file type and capacity of the playing track from USB/
SD. If the audio on your USB flash drive/ SD Card is organized into folders, the "FOL-" and "FOL+"
can be an quick way to move from one folder to the next.

7. The name of track will display here.

-5-