QED Systemline User Manual

Systemline

USER GUIDE

ZINS519

Systemline

USER GUIDE

QED Audio Products Ltd,

Ridgeway House, Ridgeway Close,

Lightwater, Surrey GU18 5XU

Tel : [phone]
Fax: [phone]

Email:[e-mail]

Internet:http://www.qed.co.uk

CONTENTS PAGE

Component Overview 1
KMS in Detail 2
DMS in Detail 3-4
RHS in Detail 5

How to use this guide

Because Systemline offers many variations this guide has tick boxes to show which
variation is applicable to your installation. Your installer will fill these in for you.

INSTALLATION DETAILS

Systemline Controller Serial Number: ___________________________________

Installer details:

Installer contact name: _______________________________________________
Installer contact tel no: _______________________________________________

Source Equipment Details:

Source 1: _______________________________________________
Source 2: _______________________________________________
Source 3: _______________________________________________
Source 4: _______________________________________________

USER GUIDE 5

RHS

INSTALLED?

√

Select and Play CD Stop CD Skip up track Skip down track

Select Random Play Skip up disc

Select and Play Tape Stop Tape Wind reverse Wind forward

Select Satellite receiver Down one channel Up one channel

Select and Play Video Stop Tape Wind reverse Wind forward

Pause Tape Down one channel Up one channel

Select and Play CD2 Stop CD Skip up track Skip down track

No function Select Random Play Skip up disc

Select Tuner2 Returns to favourite station Move up one Pre-set station Move down one Pre-set station

No function No function No function

Select Tuner Returns to favourite station Move up one Pre-set station Move down one Pre-set station

√

If Mini Disc is installed, Random and Disc Skip will have no function

Select and Play DVD Stop DVD Scan reverse Scan forward

Pause DVD Track back Track forward

INSTALLED?

√

Systemline

USER GUIDE

KMS - Source Selection & Volume

*ENGAGED display is a courtesy notice to indicate that the source chosen
is being played in another zone already. It is still possible to change the
source but it may effect the listening pleasure of another zone.

Volume is displayed from 0-63 (0=OFF). ie Vol 34
Time is displayed whilst system is in Stand-by. ie 13:21

(()) indicates that the paging has been activated
Mute indicates volume at zero (zone is still ON)
Stby indicates Stand-by mode (zone is OFF), this display is then followed

by the time display. ie 13:21

Source Selection Keys

Press one of these

buttons to get sound

Volume

+ Increase volume

- Decrease volume

DMS

KMS - Source Control Options

NORMAL ENGAGED*

SOURCE 1 Tunr tunr

SOURCE 2 Cdcd

SOURCE 3 Tape tape

or Sat sa t

SOURCE 4 Dvd dvd

or Tun2 tun2

or Vcr vc r

or Cd2 cd2

TUNER Pre-set down Pre-set up Pre-set 1

CD Track up Track down Stop Disc up

MD Track up Track down Stop

TAPE Back wind Forward wind Stop

SATELLITE Channel up Channel down

VCR Back wind Forward wind Stop Pause

DVD Track up Track down Stop

TUNER2 Pre-set down Pre-set up Pre-set 1

CD2 Track up Track down Stop Disc up

Source

Control

<>

INSTALLED?

√

INSTALLED?

√
√

USER GUIDE 2

USER GUIDE 3

Mute speakers
Stand-by (zone only)
5 second push = Power down (OFF)

2

2

SYSTEM OVERVIEW

Your Systemline installation will include some, if not all, of the following items:

To program alarm or change time* (assuming DMS is in Stand-by mode)

If a zone splitter is installed within a zone to allow you to switch between a 2nd set of speakers
in a different room there will be an illuminated LED below the one or both of the two buttons
marked "A" and "B".

The illuminated LED indicates that the speakers are active. It is possible to have pair "A" active
or pair "B" active or both. Note it is not possible to turn both pairs OFF so if you wish to switch
from pair "A" to pair "B" you must first activate pair "B" before being able to deactivate pair "A".

Systemline

USER GUIDE

Systemline Controller S4.3

Nerve centre of the system. The
Controller should be left switched
on permanently, and once set up
by your installer it should need
no further adjustment.

Display Module (DMS)

Displays information about the
status of Systemline and also
receives commands from RHS

Remote Handset (RHS)

Issues commands to select
and control sources from the
comfort of your armchair.

Keypad Module (KMS)

Used to select source and issue
commands to that source.

USER GUIDE 1

USER GUIDE 4

Prime Zone (A)

Selected

(B) Sub Zone
Selected

*Clocks on dms displays will synchronise with the clock on zone a dms at 12:00

Press

Alarm button

Press

Alarm button

Press

Alarm button

Press

Alarm button

Press

Alarm button

Alarm ON

Advances

hours

Use Tuner

Advances

hours

Alarm OFF

Advances

minutes

Use CD

Advances

minutes

Enters alarm On/Off mode

Enters alarm setting mode

Enters source selection mode

Enters clock setting mode

Exits set up mode

DISPLAY BUTTON A BUTTON B