QDI QD6580W V2.0 MTL setting manual edited

Page 1

QDI COMPUTER, INC. QD6580W V2.0(S2.1)

32-bit VL-busData bus: Three-quarter length, half-height cardSize: Four IDE(AT) drivesHard drive supported: Two 360KB, 720KB, 1.2MB, or 1.44MB drivesFloppy drives supported:

CN5

JP3

JP1

JP2

JP4

CN1

JP5

JP6-JP13

CN2

CN8

CONNECTIONS

PARALLEL PORT ADDRESS SELECTION

CN3

CN4

JP14

JP15

JP16

CN6

CN5

JP17

JP19

JP20

JP18

LocationFunction

CN140-pin primary IDE(AT) connector CN240-pin secondary IDE(AT) connector CN334-pin cable connector - floppy drive CN416-pin game port CN59-pin serial port 1 - external, 10-pin serial port 1 internal CN610-pin serial port 2 - internal CN725-pin parallel port - external CN82-pin connector - drive active LED

JP7JP6LPT pins 1 & 2 closedpins 2 & 3 closedí LPT1 (378h) pins 2 & 3 closedpins 1 & 2 closedLPT2 (278h) pins 2 & 3 closedpins 2 & 3 closedLPT3 (3BCh) pins 1 & 2 closedpins 1 & 2 closedDisabled

Continued on next page. . .

CN7

JP21 JP22

C0852

Page 2

Volume 3 - Controller Cards

QDI COMPUTER, INC. QD6580W/757/777/787/797VL

. . .continued from previous page

USER CONFIGURABLE SETTINGS

Function Location Setting í Primary IDE controls disk peripherals only JP1 open

Primary IDE controls disk and non-disk peripherals JP1 closed

í Sense clock frequency from VL slot JP2/pins 2 & 3 closed

Does not sense clock frequency from VL slot JP2/pins 1 & 2 closed

í IDE(AT) interface enabled JP3/pins 2 & 3 closed

IDE(AT) interface disabled JP3/pins 1 & 2 closed

í Primary IDE at 1FXh & secondary IDE at 17Xh enabled JP4 closed

Only primary IDE at 1FX enabled JP4 open

í Chipset register address is 0BXh JP5/pins 2 & 3 closed

Chipset register address is 03Xh JP5/pins 1 & 2 open

í Floppy drive interface enabled JP12/pins 2 & 3 closed

Floppy drive interface disabled JP12/pins 1 & 2 closed

í Floppy drive order is normal (A:, B:) JP13/pins 2 & 3 closed

Floppy drive order is reversed (B:, A:) JP13/pins 1 & 2 closed

í Game port enabled JP14 closed

Game port disabled JP14 open

í Parallel port IRQ 7 select JP15/pins 2 & 3 closed

Parallel port IRQ 5 select JP15/pins 1 & 2 closed

í Parallel port is unidirectional JP16 closed

Parallel port is bi-directional JP16 open

í Factory configured - do not alter JP17 N/A í Factory configured - do not alter JP18 N/A í Factory configured - do not alter JP19 N/A í Factory configured - do not alter JP20 N/A í Factory configured - do not alter JP21 N/A í Factory configured - do not alter JP22 N/A

SERIAL PORT 1 ADDRESS SELECTION

COM JP8 JP9 í COM1 (3F8h) pins 2 & 3 closed pins 1 & 2 closed COM3 (3E8h) pins 1 & 2 closed pins 2 & 3 closed

Disabled pins 1 & 2 closed pins 1 & 2 closed

SERIAL PORT 2 ADDRESS SELECTION

COM JP10 JP11 í COM2 (2F8h) pins 2 & 3 closed pins 1 & 2 closed COM4 (2E8h) pins 1 & 2 closed pins 2 & 3 closed

Disabled pins 1 & 2 closed pins 1 & 2 closed