QUICK START GUIDE
D
CARE AND WARNING
WARNING: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
QUICK START GUIDE
Quick Start Guide
This quick guide will help you go through installation quickly
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/panel PC technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,including interference that may
cause undesired operation.
Correct Disposal of this product. This marking indicates that this product should
not be disposed with other household wastes throughout the EU. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return your used
device, please use the return and collection systems or contact the retailer where the
product was purchased. They can take this product for environmental safe recycling.
“ FCC & CE RF Radiation Exposure Statement Caution: To maintain compliance with
the FCC & CE’s RF exposure guidelines, place the product at least 20cm from near by
persons. ”
Box PC BXP series
Adaptor with ferrite must be used with this equipment to ensure
compliance with the Class B FCC limits.
Power Adapter information:
Model No.: KSASB0241200150D5
INPUT: 100-240V~50/60Hz 0.6A
OUTPUT: 12V 1.5A
Qbic Technology Co.,Ltd.
11F.-9,No.99.Sec.1, Xintai 5th Rd., Xizhi Dist., New Taipei City 221, Taiwan(R.O.C)
Tel: 886-2-2697-2000 FAX: 886-2-2697-2868
The colour and the appearance may differ depending on the
product, and the specifications are subject to change without
prior notice to improve the performance.
QUICK START GUIDEQUICK START GUIDE
A
Contents
Box PC
HDMI Cable
(BXP-300 with 1pcs
BXP-301&202 with 2pcs)
DC & Micro SD
Card Cover
B
Indication
1
2
3
4
Quick Start Guide
Velcro Strip
HDMI Cover
（BXP-300 with 1pcs
BXP-301&202 with 2pcs)
DC Power Adapter
External Antenna
Setscrew M2
（BXP-300 with 2pcs
BXP-301&202 with 3pcs)
for EUfor US
for UK
Power Plug
( Provided by regions）
for AU
Air Mouse
(Optional)
4K
IN
+
DUAL
C
Installation
1. Cables Connection
Audio Cable
RS-232 Terminal
S/PDIF
LAN Cable
HDMI
HDMI
HDMI
Fix DC jack with DC
cover and M2 screw
Fix HDMI connector with
HDMI cover and M2 screw
（BXP-300 )
DC IN
Fix HDMI connector with
HDMI cover and M2 screw
（BXP-301 )
External WiFi Antenna
USB
USB
ADB
Fix HDMI connector with
HDMI cover and M2 screw
（BXP-202 )
2. Surface Mount
Step 1
5
6
7
Surface
Step 2
mm100.00
100.00
mm
Surface
1
2
Audio Out
3
RS-232(Male)
4
S/PDIF
BXP-300
BXP-301
BXP-202
8 9 10 11
5
USB
6
USB
7
ADB
8
LAN
9
ResetWiFi Antenna
10
Micro SDHC
11
DC 12V
12
HDMI OUT
BXP-300 BXP-301
12
13 14
15 16
13
14
15
16
BXP-202
HDMI OUT
HDMI IN
HDMI OUT
HDMI OUT
Mark the screw hole
location on the surface
Fix Box PC with screws
* Recommand to mount
Box PC with four M4
screws according to the
3. Velcro Mount
above illustration.
Step 1 Step 2 Step 3
Metal(AI&SS)
Galss
Plastics(Acrylic, PC, ABS)
Surface
* Please ensure the mounting surface is clean and smooth before using the Velcro strip.
Please visit this link for software user manual.
http://www.qbictechnology.com/suppor t
Loading...