USE AND CARE GUIDE
®
QBD
VISI COOLER
MODELS: DC3H, DC4H, DC6H, DC6HG, DC7H, DC7HG DC10HB, DC12HB
|
CONTENT |
PAGE# |
|
|
|
Introduction |
|
2 |
|
|
|
Important Use and Safety Instructions |
3 |
|
|
|
|
Operating Your Visi Cooler |
4 |
|
|
|
|
Preparation, Care and Cleaning |
5 |
|
|
|
|
Installation Requirements |
6 |
|
|
|
|
Wiring Diagrams |
7-8 |
|
|
|
|
Reversing the Door Swing |
9 |
|
|
|
|
Shelf Stopper Clip Mounting Instruction |
10 |
|
|
|
|
Pallet Removal Instruction |
10 |
|
|
|
|
Door Handle Installation Instruction |
11 |
|
|
|
|
Questions? |
Problem Solver |
12 |
|
|
|
Questions? |
Service Providers, Warranty |
12 |
|
|
|
®
QBD Cooling Systems Inc.
31 Bramsteele Rd.,Brampton, Ontario, Canada L6W 3K6 Tel: (905) 459-0709 Fax: (905) 459-1478
NOVEMBER 2007 |
PUBLICATION 47-0480-109C |
INTRODUCTION
Read this book carefully....
It is intended to help you operate and maintain your new cooler properly. Always keep it handy.
If you don’t understand something or need more help, please write or phone to:
Manager, Customer Service, |
|
QBD Cooling Systems Inc. |
Tel. 1(905) 459 0709 |
31 Bramsteele Road, |
1(800) 663 3005 |
Brampton, Ontario, |
Fax. 1(905) 459 1478 |
Canada L6W 3K6 |
Web Pagehttp://www.qbd.com |
We are proud of our service and want you to be pleased. If for some reason you are not happy with the service you receive, here are two steps to follow for further help.
FIRST , contact the people who serviced your cooler. Explain why you are not pleased. In most cases this will solve the problem.
NEXT, if you are still not pleased, write all the details - including your phone number to QBD`s above address or fax. at: 1(905) 459 1478 or call : 1(905) 459 0709 ; 1(800) 663 3005.
E-Mail- info@qbd.com
If you received a damaged cooler . . .
Immediately contact the carrier that delivered you the cooler for all your claims.
All goods are shipped at the customers risk.
Return of goods to the factory must have the authorized approval of QBD.
No returns will be accepted after 10 days.
Any shortage claims must be made within 5 days of receiving the goods.
How to unpack your cooler. . .
DC3, DC4, DC6 and DC7 - First remove all the outer packing material on the cooler. Then dismantle the skids at the base by tilting the cooler to one side [right]. Use a Philips screwdriver to remove the two screws on the wooden base. Repeat the same operation by tilting the cooler to the left hand side . Push the wooden blocks away and your unpacked cooler is on its feet....
DC10, DC12 - For pellet removal instructions, see page 8
Save time and money. Before you request service. . .
Check the Problem Solver in the back of this book. It lists the minor operating problems that you can solve yourselves.
Write down the model and serial numbers.
You will see them on a label in the cooler. Please write these numbers and the purchase date here:
Model Number: __________ Serial Number: _________________ Purchase Date: ______
Please use these numbers and the date in any correspondence or service calls concerning your cooler.
2
IMPORTANT USE AND SAFETY INSTRUCTIONS
Read all instructions before using this appliance.
∙This cooler must not be stored outdoor or in ambient conditions where the temperature may exceed 105º F (41ºC), or in direct sunlight.
∙This cooler is designed to be used indoor only, in ambient conditions of 65º-90º F ( 18º-32ºC) with 60% relative humidity.
∙Use this cooler only for its intended purpose as described in this Use and Care Guide.
This equipment is intended for the storage and display of non-potentially hazardous, bottled or canned products only.
∙For trouble free operation, it is recommended that the condenser be cleaned every 1 to 2 month. Failure to clean condenser can cause compressor malfunction and VOID WARRANTY.
∙For compliance to the NSF sanitation requirements DC7 cooler must be mounted in one of the fol-
lowing ways:
1. Sealed to the counter top.
The lower perimeter of the cooler cabinet must be sealed to the counter top using flexible PVC baseboard trim.
This baseboard trim is available from your local lumber –hardware supplier or from QBD’s order desk. A PVC baseboard trim with a self-adhesive back is ideal for this application.
The baseboard trim will be applied to the complete perimeter of the cooler except for the area around the lower door hinge. The hinge is not sealed to the counter top to facilitate maintenance and servicing.
The baseboard is pressed tightly against the vertical wall of the cooler while the lower edge of the baseboard trim is pressed downward against the counter top and thereby providing a tight seal around the base of the cooler.
Because of the flexibility of the PVC baseboard trim a good seal is achievable on counter tops that are curved or bowed.
OR
2. Elevated on legs that provide a minimum clearance of 10cm (4 in) beneath the unit.
*Optional NSF Certified legs are available from QBD’s order desk. Ask for QBD part number 47-0530-204. Four (4) legs per cooler are required.
WARNING ! When using this appliance, always exercise basic safety precautions, including the following:
∙This cooler must be properly installed in accordance with the Installation Instructions before it is used. See grounding instructions and the Installation Sections.
∙Never unplug your cooler by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.
∙Repair or replace immediately all electric service cords that become frayed or otherwise damaged.
Do not use a cord that shows cracks or abrasion along its length or at either the plug or connector end.
∙Unplug the cooler before cleaning and making repairs.
Note: We strongly recommend that any servicing be performed by a qualified Technician.
∙Before replacing a burnt out lamp, the cooler should be unplugged in order to avoid contact with a live wire filament. [A burned out lamp may break when being replaced.]
Note: Turning the control to the OFF position does not remove power to the light circuit.
∙Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
3
OPERATING YOUR VISI COOLER
Energy - Saving Tips. . .
Location of your cooler is important. Avoid locating it next to a vent or where the sun will shine directly on the appliance.
Close the door as soon as possible, particularly in a hot and humid weather.
Keep back of the cooler minimum 3 in.(76. mm) away from the wall.
Clean Condenser frequently, every 1 to 2 month.
Temperature Control Dial
The temperature control dial has settings from 1 to 9 plus “OFF”. 1 is the warmest setting.
9 is the coldest setting.
Initially set the temperature to the recommended setting shown on the label at the internal cabinet serial-name plate.
After using the cooler for 24 hours, adjust the temperature control to the setting that is best suited for your needs.
NOTE : If the cooler is unplugged or turned off, you must allow 3 minutes before starting it or plugging it back in. If you attempt to restart it in less than 3 minutes, it may not restart and it may damage the compressor and VOID WARRANTY.
Turning the temperature control dial to “OFF” stops cooling but does not shut off power to the cooler.
Shelves
Shelves in DC3H, DC4H, DC6H/DC6HG, DC7H/DC7HG, DC10HB and DC12HB can be moved to different levels to suit your varying storage needs.
See page 8 for shelf stopper clip mounting instructions, specific to DC10HB and DC12HB.
Leveling Legs
Adjustable legs at the front should be set so that the cooler is firmly positioned on the countertop or floor. Turn leveling legs counterclockwise to raise the cooler, clockwise to lower it.
Note :
Do not raise the front wheels of the DC10, DC12 more than 1/16”
4
Loading...