Technical Support Line: (952) 985-5675 Email: Sales@QA1.net
21730 Hanover Ave.
Lakeville, MN 55044
www.QA1.net
ASSEMBLY INSTRUCTIONS
P/N CK1950, CK1951C, CK1955C
Coil-Over Hardware Kit for QA1 75 Series & Streeters Shocks
READ ALL INSTRUCTIONS CAREFULLY AND THOROUGHLY PRIOR TO STARTING INSTALLATION. PRODUCTS THAT HAVE BEEN INSTALLED ARE NOT ELIGIBLE FOR
RETURN. USE THE PROPER JACKING LOCATIONS. DEATH OR SERIOUS INJURY CAN RESULT IF INSTRUCTIONS ARE NOT CORRECTLY FOLLOWED. A GOOD CHASSIS
MANUAL, AVAILABLE AT YOUR LOCAL PARTS STORE, MAY ALSO AID IN YOUR INSTALLATION.
QA1 WARRANTS THAT THE PRODUCTS WILL BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP FOR ONE YEAR FROM DATE OF SALE TO THE ORIGINAL
PURCHASER. QA1 MAKES NO OTHER WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. QA1 SHALL HAVE NO OBLIGATION UNDER THE FOREGOING WARRANTY
WHERE THE DEFECT IS THE RESULT OF IMPROPER OR ABNORMAL USE, YOUR NEGLIGENCE, VEHICLE ACCIDENT, IMPROPER OR INCORRECT INSTALLATION OR
MAINTENANCE, NOR WHEN THE PRODUCT HAS BEEN REPAIRED OR ALTERED IN ANY WAY. QA1’S LIABILITY IN THE CASE OF DEFECTIVE PRODUCTS SUBJECT TO
THE FOREGOING WARRANTY SHALL BE LIMITED TO THE REPAIR OR REPLACEMENT, AT QA1’S OPTION, OF THE DEFECTIVE PRODUCTS.
THE USER UNDERSTANDS AND RECOGNIZES THAT RACING PARTS, SPECIALIZED STREET ROD EQUIPMENT, AND ALL PARTS AND SERVICES SOLD BY QA1 ARE
EXPOSED TO MANY AND VARIED CONDITIONS DUE TO THE MANNER IN WHICH THEY ARE INSTALLED AND USED. QA1 SHALL BEAR NO LIABILITY FOR ANY LOSS,
DAMAGE OR INJURY, EITHER TO A PERSON OR TO PROPERTY, RESULTING FROM THE INSTALLATION, DIRECT OR INDIRECT USE OF ANY QA1 PRODUCTS OR
INABILITY BY THE BUYER TO DETERMINE PROPER USE OR APPLICATION OF QA1 PRODUCTS. WITH THE EXCEPTION OF THE LIMITED LIABILITY WARRANTY SET
FORTH ABOVE, QA1 SHALL NOT BE LIABLE FOR ANY CLAIMS, DEMANDS, INJURIES, DAMAGES, ACTIONS, OR CAUSES OF ACTION WHATSOEVER TO BUYER
ARISING OUT OF OR CONNECTED WITH THE USE OF ANY QA1 PRODUCTS. MOTORSPORTS ARE DANGEROUS; AS SUCH, NO WARRANTY OR REPRESENTATION IS
MADEAS TO THE PRODUCT’S ABILITY TO PROTECT THE USER FROM INJURY OR DEATH. THE USER ASSUMES THAT RISK!
• DISCLAIMER / WARRANTY •
TOOLS NEEDED
• Spanner Wrench, QA1 P/N T120W • Permatex® Anti-Seize Lubricant • Lock Ring Pliers
Assembly Instructions
1. Place locking ring on grooved portion of shock body. 6” and 7” stroke shocks will have two grooves that will accept
the lock ring. Use ring groove closest to eyelet on 6” and 7” shocks using 12” & 14” springs.
2. Place threaded sleeve over shock body. One end of the inner sleeve is beveled. Install beveled end FACING
LOCK RING over the lock ring, locking the sleeve into place.
9919-214 1 Rev. 07252017
3. Lightly coat the coil-over threads with anti-seize before threading
collars down the body. Thread locking collar onto the coil-over
sleeve with shouldered side facing up. Place O-ring on top of locking
collar. Thread the spring seat collar on top of the locking collar/Oring. These collars should be threaded down to the bottom of the
threaded sleeve to make room for the spring/spring cap.
4. Place spring over coil-over sleeve.
5. Place spring cap on top of spring and install pin to secure. Zip ties
are also included for circle track use.
9919-214 2 Rev. 07252017
Loading...