Q3 Innovations UV HAWK 2 User Manual

1. Press the “SPF/SKIN” button. The SPF icon should now be flashing.

INDEX SENSOR

LCD DISPLAY

Owner’s Manual

v030110

Introduction

Overview

The UV HAWK™ 2 is a device that measures the intensity of ultraviolet (UV) light and displays the results in
the UV Index Scale. The higher the UV Index the greater the amount of potentially skin damaging UV light.
The UV HAWK™ 2 operates on a single CR2032 cell battery.

Features

 UV index display
 Ambient temperature display
 Waterproof exterior
 Sleek design
 Compact size
 Overexposure alarm

Operating Instructions

Power On and Measurement

1. Always make sure the sensor lens is clean without any damage before measurement.

2. Press the “ON/OFF” button to power ON.

3. Position the UV HAWK™ 2 under sunshine and make sure that the U V In de x S enso r is directly facing the light source.

4. Press and hold the “Meas./Adj.” button for about two seconds until the UV Index and Temperatur e rea din gs are flashing.

5. Wait 3 seconds until the sun icon disappears and Temperature reading stops flashing and THEN read the UV Index and Temperature
readings.

Changing SPF and Selecting Skin Type

UV

2. Press the “Meas./Adj.” button to adjust the SPF value (from 0 - 100).

3. Press the “SPF/SKIN” again. The SKIN icon should now be flashing.

4. Press the “Meas. /Adj. button to select the skin type (from 1 to 4). Refer to
following table for choosing the correct skin type.

5. Press the “SPF/SKIN” button again to set the above values again.

Recommended Skin Type Selection and Skin Sensitivity Value (SSV)

Skin Category Unexposed Skin Color Tanning History Skin Type

Never tans, always bu rns Pale or milky, white alabaster Develops red sunburn, painful swelling, skin peels 1

Sometimes tans, usual l y burn s Very little brown, sometimes freck l es

Usually tans, sometimes burns Light tan, brown or olive, distinctly pigmented Rarely burns, moderately rapid tanning response 3

Always tans, rarely burns Brown, dark brown or black Rarely burns, ver y ra pid tanning response 4

Reading the Results and Overexposure Alarm

1. The reading at the top of the screen changes from “Sun Exposure %” to “Time
Left before Overexposure” every 6 seconds.

a. Sun Exposure % - Percentage of total recommended exposure volume,

calculated by UV index, SPF and skin type.

b. Time Left for Safety Exposure - Time left to reach the total recommended

exposure volume, calculated by UV index, SPF and skin type.

2. When the Sun Exposure % reaches 100% or Time Left before
Overexposure reaches 0 the Overexposure Alarm will be activated.

3. Press and hold the ON/OFF button for two seconds to turn off the Overexposure
Alarm.

4. Press and hold the ON/OFF button for two seconds to power off the device.

Usually burns, pink or red coloring appears,

2

can gradually develop light brown tan

Changing the Temperature Scale

Storage Conditions: 0-50°C (32-122°F)

Dimensions: 2.3” x 1.3” x 0.5” (59mm x 32mm x 14 mm)

1. Press and hold the “Meas./Adj.” button for about two seconds until the UV Index
and Temperature readings are flashing.

2. Press the “SPF/Skin” button to toggle between °C and °F.

Battery Replacement

Follow these instructions to change the batt ery when the low battery icon on the unit is displa yed:

1. Remove the screw located on the top backside of the unit and pull the shell apart gently.

2. The battery will be located on the bottom portion of the interior of the unit. Slide the old battery out of the holder.

3. Replace with a new CR2032 battery with the positive side facing up and negative side facing down.

4. Snap the shell gently back in place and tighten the screw.

Specifications

 UV Index Range: 0 to 15
 Temperature Scale: °C/°F
 SPF Range: 1-99


 Power Source: CR2032 Battery (included)
 Power Voltage: 3 Voltage
 Power Consumption: standby 10uA, testing: 1mA


Important Notes

1. Keep the lens clean for accurate measurement.

2. Gently wipe lens surface with a cotton sw ab or soft clo th moistened with water or medical alcohol.

3. Keep the unit dry and away from any liquids, sunlight and wind.

Disclaimer

Manufacturer and Q3I expressly disclaim any liability for incidental, special, or consequential damages of any nature when using this device. This device should only be used
for gauging ultraviolet light intensity. This device is NOT designed for any clinical or medical applications. This device should only be used in accordance with the
instructions and when ob e yin g all precautions and warnings.

Limited Warra n ty

Manufacturer and Q3I warrant this device to be free from defects in workmanship or material under normal use for one year from the date of purchase. Manufacturer’s
obligations under this lim ited w ar ra nt y are lim it ed to repl acing, adjusting, or repairing the unit if returned along with the proof of purchase. This warranty is void if the unit has
been tampered with, maliciously damaged, or physically abused.

The enforceability of this warranty is limited to the original consumer purchaser and is not transfer able to, or enforceable by, any subsequent owner. In the event of a defect,
malfunction or other failure to conform to this warranty, Q3I will, at its sole discretion, repair or replace the unit at no charge. You are responsible for all shipping cost in
connection with warranty service. This warranty commences on the date of retail purchase and shall be effective for a period of one year.

THERE ARE NO EXPRESS WARRANTI ES COVERING THE UNIT OTHER THAN THOSE SET F OR TH IN THIS WARRANTY. ALL IMPLIED WARRANTIES ARE LIMITED TO
THE PERIOD OF THIS WARRANTY AND NO WARRANTIES, EXPRESS OR IMPLIED, EXTEND BEYOND THIS PERIOD. SOME STATES DO NOT ALLOW LIMITATIONS
ON HOW LONG AN IMPLIED WARRAN TY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

Manufacturer and Q3I will in no event be liable for any consequential, incidental, indirect or special damages (including, but not limited to, lost profits) arising out of or in
connection with the use, misuse or function of the unit. Some states do not allow exclusion of limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

If you feel the device is not functioning properly, please review this manual, particularly the instructions. If you still feel warranty service is required, please follow
the below instructions:

1. To obtain service during the warranty period, please call 888.399.1687 or email [e-mail] to obtain a Return Authorization number and shipping instructions.
Remember to return the device postage paid, insured and in suitable packaging.

2. For your own protection, obtain a proof of deliv e r y recei pt. Ship pi n g costs ar e your responsibility.

3. You must enclose with the unit the following information:

a. Your name, complete return address and written description of the problem (No PO Box please.)
b. A telephone number where you can be reached during normal business hours.
c. A copy of your dated sales receipt or invoice.

Q3 Innovations

2349 Jamestown Avenue, Suite #4, Independence, IA 50644

Tel: [phone] Fax: [phone] E-mail: [e-mail]

www.q3i.com