Pyronix XDL12TT-AM Installation Manual

 [phone] (UK)  [e-mail] (UK)  www.pyronix.com Pyronix Limited, Pyronix House, Braithwell Way, Hellaby, Rotherham, S66 8QY, UK

Tri-detection method

2 digital dual-element passive IR & 1 microwave
doppler unit

Sensitivity

AUTO or HIGH

Temperature compensation

Digital

Pet immunity

Up to 24kg, 1m high

Detection speed

0.25 - 2.5m/s

Tri-masking

Adjustable from 0m to 1m, covers all 3
technologies

Casing

3mm polycarbonate, 0.4mm HDPE in Lens Area.
IP Rating: IP55

Lenses

UV compensated

Operating voltage & current

9 - 16V DC, (24mA @ 13.8V DC quiescent)

Relay output

3 x SELV limits, 60V DC 50mA (42.4V AC peak)

Mounting height & range

1m - 1.5m = 12m range

Tamper switches

12V DC 50mA both front and rear

Temperature

Storage: -40°C to 80°C
Operating: -30°C to 70°C

Dimensions & weight

188 x 77 x 84mm, 0.3kg

Product information

Applies to electrical products sold within the European community. At the end of the electrical product’s life,
do not dispose of it with household waste. Where possible, recycle the product. Check with your Local
Authority or retailer for recycling advice in your country.

Warranty

This product is sold subject to our standard warranty conditions and is warranted again defects in
workmanship for a period of five years (excluding lens). In the interest of continuing care and design, Pyronix
Ltd reserves the right to amend specifications without giving prior notice.

Environmental Class (EC) IV

9.9GHz: AT, BE, CH, CY, CZ, DK, EE, FI,
FR, GR, HR, HU, IE, IS, IT, LT, MT, NL,
PL, PT, SI, TR, UAE

10.525GHz: BE, CH, CY, DK, ES, HU, IE,
IS, IT, MT, MY, NL, NO, SE, SI, UAE, USA

10.587GHz: GB, MY

EN

XDL12TT-AM

RINS1900-1

1. Installation

Scan the QR code for fixing instructions and adapter information. Ensure that the detector is
installed away from reflected sunlight and large objects.

2. Switches

If you disable the detector’s LEDs, you can remotely enable them in walk tests. Connect the
detector’s LED terminal to a control panel PGM output that switches to 0V to enable the LEDs.

3. Microwave range and angle of detection

Use the highlighted dials to change the microwave range and angle of detection.

4. LEDs

Four LEDs show the status of the detector.

5. Lens inserts

Use lens inserts to control coverage.

6. Header pins

Place two-pin jumpers onto header pins to adjust resistance for alarm, masking/fault and tamper.

7. Anti-masking

Anti-masking triggers an alarm when part or all of the sensor is masked by an intruder. Use the
highlighted dial to change the masking area range. When an intruder enters the masking area,
LED2 pulses. When the intruder moves out of the masking area, if the detector does not see
activation on all 3 sensors within 1 min, the mask/fault relay opens and LED1 and LED3 turn on.
To reset, remove the obstruction and perform a walk test for 1 min.

8. Blocking

Blocking detects intruders behind objects when the panel is disarmed. To use blocking, move
switches 3 and 4 down, and connect the R1 input to a panel output that is negative when
disarmed. When blocking is active, the alarm relay opens and LED1 and LED3 turn on. To reset,
perform a walk test.

9. Connecting to CCTV and lights

To connect the detector to CCTV and lights, refer to the wiring diagram.

Specifications

4m 8m 12m

1-1.5m

1-1.5m

< 24kg

1m

4m 8m 12m

1-1.5m

< 10m

4m 8m 12m

1-1.5m

> 10m

4m 8m 12m

ON

LED 1 LED 2 LED 3

LED 4

Top PIR activated

Bottom PIR activated

Microwave activated

Alarm

Powering up

Low voltage

Top PIR failed self-test

Bottom PIR failed self-test

Microwave failed self-test

Masked / blocked

Mask processing

12m

1.3m

1.3m

~8m

0m

12m

12m

12m

1-1.5m

1

2

3

2

4

5

1-1.5m

4m 8m 12m

Switch

1
2
3
4
5
6
7
8

Up (ON position)

AC 230V, 50 Hz
Anti-masking always on
Blocking off
R1 off
Auto sensitivity
Open mask & alarm relays
Buzzer on
LEDs on

Down

AC 110V, 60 Hz
Anti-masking on when disarmed
Blocking on when disarmed
R1 on
High sensitivity
Open mask relay only
Buzzer off
LEDs off

2

2

 [phone] (UK)  [e-mail] (UK)  www.pyronix.com Pyronix Limited, Pyronix House, Braithwell Way, Hellaby, Rotherham, S66 8QY, UK

+ -

TAMPER ALARM N / C

XDL12TT-AM

MASK / FAULT

PCX

+12V 0V

EOL EOL EOL

R1 LED ALARM N / O

1

6

8

9

10K
6K8
5K6
4K7
3K9
2K7
2K2
1K5
1K
820R

3K
15K
12K
8K2
6K8
5K6
4K7
2K2
1K

10K
5K6
4K7
3K9
2K7
2K2
1K5
1K

<1m

30%

0%

7

+ -

TAMPER ALARM N / C

XDL12TT-AM

MASK / FAULT

2K2
1K5
1K
820R

T

PCX

+12V 0V A

T

COM

A

EOL

EOL EOL EOL

R1 LED ALARM N / O

ALARM N/C

5K6
4K7
3K9
2K7

10K
6K8

5K6
4K7
2K2
1K

MASK / FAULT

15K
12K
8K2
6K8

10K
3K

2K2
1K5
1K

TAMPER N/C

5K6
4K7
3K9
2K7

10K

DEOL

+ -

TAMPER ALARM N / C

XDL12TT-AM

MASK / FAULT

2K2
1K5
1K
820R

T

PCX

+12V 0V A

T

COM

A

EOL

EOL EOL EOL

R1 LED ALARM N / O

ALARM N/C

5K6
4K7
3K9
2K7

10K
6K8

5K6
4K7
2K2
1K

MASK / FAULT

15K
12K
8K2
6K8

10K
3K

2K2
1K5
1K

TAMPER N/C

5K6
4K7
3K9
2K7

10K

3EOL

+ -

TAMPER ALARM N / C

XDL12TT-AM

MASK / FAULT

2K2
1K5
1K
820R

T

PCX

+12V 0V A

T

COM

A

EOL

EOL EOL EOL

R1 LED ALARM N / O

ALARM N/C

5K6
4K7
3K9
2K7

10K
6K8

5K6
4K7
2K2
1K

MASK / FAULT

15K
12K
8K2
6K8

10K
3K

2K2
1K5
1K

TAMPER N/C

5K6
4K7
3K9
2K7

10K

N/C

DEOL

N/C

+ -

TAMPER ALARM N / C

XDL12TT-AM

MASK / FAULT

T

PCX

+12V 0V A

T

COM

A

EOL

EOL EOL EOL

R1 LED ALARM N/O

NO C NC

PGM

0V

= 0V

PROGRAM OUTPUTS?

PGM [0000]
Not Used

Endstation PGMs?

PGM [0022]
Final Arm Any

PCX